TABLE OF CONTENTS 1 Before driving Adjusting and operating features such as door locks, mirrors, and steering column. 2 When driving Driving, stopping and safe-driving information. 3 Interior features Air conditioning and audio systems, as well as other interior features for a comfortable driving experience. 4 Maintenance and care Cleaning and protecting your vehicle, performing do-ityourself maintenance, and maintenance information.
TABLE OF CONTENTS 1 Index 1-6. Theft deterrent system Before driving Engine immobilizer system................................ 85 Double locking system ......... 92 1-1. Key information Keys...................................... 28 1-7. Safety information Correct driving posture......... 94 SRS airbag (Supplemental Restraint System airbag) ... 96 Child restraint systems....... 125 Installing child restraints..... 133 Airbag manual on-off system.............................. 148 1-2.
2-2. Instrument cluster Gauges and meters ............ 190 Indicators and warning lights ................................. 195 Multi-information display ..... 200 2-3. Operating the lights and windshield wipers Headlight switch.................. 205 Fog light switch ................... 212 Windshield wipers and washer .............................. 214 2-4. Using other driving systems Cruise control...................... 217 Driving assist systems ........ 222 2-5. Driving information Cargo and luggage ....
TABLE OF CONTENTS 4 Index Maintenance and care 5 4-1. Maintenance and care When trouble arises 5-1. Essential information Cleaning and protecting the vehicle exterior ........... 278 Cleaning and protecting the vehicle interior ............ 282 Cleaning and protecting the Alcantara® area .......... 286 Emergency flashers ........... If your vehicle needs to be towed ............................... If you think something is wrong ............................... Fuel pump shut off system.............
If your vehicle has to be stopped in an emergency ........................ 413 6 Vehicle specifications 1 6-1. Specifications Maintenance data (fuel, oil level, etc.)............ 416 Fuel information .................. 428 2 6-2. Customization Customizable features ........ 430 3 Index 4 Abbreviation list ........................ 434 Alphabetical index..................... 435 5 What to do if... ...........................
Pictorial index Exterior Daytime running lights (vehicle with discharge headlights) P. 205 Headlights (high beam) P. 205 Front position lights P. 205 Headlights (low beam) P. 205 Windshield wipers P. 214 Outside rear view mirrors P. 75 Hood P. 294 Turn signal lights P. 187 Turn signal lights P. 187 Front fog lights P. 212 Daytime running lights (vehicles with halogen headlights) P.
Trunk P. 53 Rear window defogger P. 252 Turn signal lights P. 187 Fuel filler door Doors P. 81 P. 50 Tail lights P. 205 Rear fog light P. 212 License plate lights P. 205 Tires Rotation Replacement Temporary repair Inflation pressure P. 311 P. 371 P. 379 P.
Pictorial index Head restraints Seat belts Interior (Left-hand drive vehicles) P. 64 P. 66 Child restraint anchor brackets SRS curtain shield airbags P. 96 P. 133 SRS front passenger airbag P. 96 Power outlet Cup holders P. 260 Console tray P. 260 SRS side airbags P. 267 P. 96 Front seats P. 58 Glove box P.
A Sun visors P. 262 Interior light P. 256 Vanity mirrors P. 263 Anti-glare inside rear view mirror B P. 74 Inside door lock buttons P. 51 Outside rear view mirror switches P. 75 Door lock switch P. 51 Power window switches Window lock switch P. 78 P.
Pictorial index Interior (Left-hand drive vehicles) C Shift lever P. 177, 184 Shift lock override button P. 397 Parking brake lever P. 188 Seat heater switches P. 269 Power outlet P. 267 “VSC SPORT” switch P. 223 Driving pattern selector switch P. 179 VSC/TRC off switch P.
Instrument panel (Left-hand drive vehicles) Pictorial index Gauges and meters P. 190 Multi-information display P. 200 Headlight switch P. 205 Turn signal lever P. 187 Fog light switch P. 212 Windshield wiper and washer switch P. 214 Clock P. 264 Emergency flasher switch P. 352 Tilt and telescopic steering lock release lever P. 73 Floor mat P. 271 Hood lock release lever P. 294 AUX/USB port P. 254 Fuel filler door opener SRS driver knee airbag P. 96 P.
Pictorial index Instrument panel (Left-hand drive vehicles) A Vehicles with a manual air conditioning system Air conditioning system P. 236 Rear window and outside rear view mirror defoggers switch /rear window defogger switch P. 252 Vehicles with an automatic air conditioning system Air conditioning system P. 244 12 FT86_EE Rear window and outside rear view mirror defoggers switch P.
B Paddle shift switches P. 180, 182 Engine (ignition) switch (vehicles without a smart entry & start system) P. 174 Horn P. 189 SRS driver airbag C Cruise control switch P. 217 P. 96 Instrument panel light control dial P. 193 Manual headlight leveling dial P. 207 Trunk opener P.
Pictorial index Interior (Right-hand drive vehicles) Head restraints SRS front passenger airbag P. 96 P. 64 Child restraint anchor brackets SRS curtain shield airbags P. 96 P. 133 Seat belts Power outlet P. 66 Cup holders P. 260 Console tray P. 260 P. 267 Glove box SRS side airbags P. 258 Front seats 14 FT86_EE P. 58 P.
A Interior light P. 256 Sun visors P. 262 Anti-glare inside rear view mirror P. 74 Vanity mirrors P. 263 B Inside door lock buttons P. 51 Outside rear view mirror switches P. 75 Window lock switch P. 78 Power window switches P. 78 Door lock switch P.
Pictorial index Interior (Right-hand drive vehicles) C Shift lever P. 177, 184 Shift lock override button P. 397 Parking brake lever P. 188 Seat heater switches P. 269 Power outlet P. 267 VSC/TRC off switch P. 223 Driving pattern selector switch P. 179 “VSC SPORT” switch P.
Pictorial index Instrument panel (Right-hand drive vehicles) Gauges and meters P. 190 Multi-information display P. 200 Headlight switch P. 205 Turn signal lever P. 187 Fog light switch P. 212 Windshield wiper and washer switch P. 214 Emergency flasher switch P. 352 Clock P. 264 Tilt and telescopic steering lock release lever P. 73 AUX/USB port P. 254 Floor mat P. 271 Hood lock release lever P. 294 Fuel filler door opener Engine (ignition) switch (vehicles with a smart entry & start system) P.
Pictorial index Instrument panel (Right-hand drive vehicles) A Vehicles with a manual air conditioning system Air conditioning system P. 236 Rear window and outside rear view mirror defoggers switch /rear window defogger switch P. 252 Vehicles with an automatic air conditioning system Rear window and outside rear view mirror defoggers switch P. 252 18 FT86_EE Air conditioning system P.
B Paddle shift switches P. 180, 182 Engine (ignition) switch (vehicles without a smart entry & start system) P. 174 Horn P. 189 SRS driver airbag C Cruise control switch P. 217 P. 96 Trunk opener P. 53 Instrument panel light control dial P. 193 Manual headlight leveling dial P.
For your information Main Owner’s Manual Please note that this manual covers all models and all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle. All specifications provided in this manual are current at the time of printing. However, because of the Toyota policy of continual product improvement, we reserve the right to make changes at any time without notice.
Installation of an RF-transmitter system The installation of an RF-transmitter system in your vehicle could affect electronic systems such as: Multiport fuel injection system/sequential multiport fuel injection system Cruise control system Anti-lock brake system SRS airbag system Seat belt pretensioner system Be sure to check with any authorized Toyota dealer or repairer, or another duly qualified and equipped professional for precautionary measures or special instructions regarding installation o
Event data recorder This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
Scrapping your Toyota The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and seat belt pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional, before you scrap your vehicle.
Your vehicle contains batteries and/or accumulators. Do not discard them into the environment but cooperate with separate collection (Directive 2006/66/ EC).
Symbols used throughout this manual Cautions & Notices CAUTION This is a warning against something which, if ignored, may cause death or serious injury to people. You are informed about what you must or must not do in order to reduce the risk of death or serious injury to yourself and others. NOTICE This is a warning against something which, if ignored, may cause damage to the vehicle or its equipment.
FT86_EE
Before driving 1-1. Key information Keys.................................... 28 1 1-4. Opening and closing the windows Power windows................... 78 1-2. Opening, closing and locking the doors and trunk Smart entry & start system .............................. Wireless remote control ...... Doors .................................. Trunk .................................. 1-5. Refueling Opening the fuel tank cap.................................... 81 31 47 50 53 1-3.
1-1. Key information Keys The following keys are provided with the vehicle. Vehicles without a smart entry & start system Keys (with a wireless remote control function) Operating the wireless remote control function (P. 47) Key (without a wireless remote control function) Key number plate Vehicles with a smart entry & start system Electronic keys • Operating the smart entry & start system (P. 31) • Operating the wireless remote control function (P.
1-1. Key information Using the mechanical key (vehicles with a smart entry & start system) To take out the mechanical key, slide the release lever and take the key out. 1 Before driving After using the mechanical key, store it in the electronic key. Carry the mechanical key together with the electronic key. If the electronic key battery is depleted or entry function does not operate properly, you will need the mechanical key. (P.
1-1. Key information NOTICE To prevent key damage Observe the following: Do not drop the keys, subject them to strong shocks or bend them. Do not expose the keys to high temperatures for a long period of time. Do not get the keys wet or wash them in an ultrasonic washer etc. Do not attach metallic or magnetic materials to the keys or place the keys close to such materials. Do not disassemble the keys. Do not attach a sticker or anything else to the surface of the key.
1-2. Opening, closing and locking the doors and trunk Smart entry & start system The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) 1 Before driving Electronic key Electronic key Electronic key Unlocks and locks the doors (P. 32) Unlocks the trunk (P. 33) Starts the engine (P.
1-2. Opening, closing and locking the doors and trunk Unlocking and locking the doors Vehicles without double locking system Grip the handle to unlock the doors. Vehicles with double locking system Grip the driver’s door handle to unlock the door. Grip the passenger’s door handle to unlock all the doors. Make sure to touch the sensor on the back of the handle. The door cannot be unlocked for 3 seconds after the door is locked.
1-2. Opening, closing and locking the doors and trunk Unlocking the trunk Press the button to unlock the trunk.
1-2. Opening, closing and locking the doors and trunk Effective range (areas within which the electronic key is detected) When locking or unlocking the doors The system can be operated when the electronic key is within about 0.4 - 0.8 m (1.3 2.6 ft.) of either of the outside door handles. (Only the doors detecting the key can be operated.) When unlocking the trunk The system can be operated when the electronic key is within about 0.4 - 0.8 m (1.3 2.6 ft.) of the trunk release button.
1-2. Opening, closing and locking the doors and trunk Operation signals The emergency flashers flash to indicate that the doors have been locked/ unlocked. (Locked: once; Unlocked: twice) When the door cannot be locked by the lock sensor 1 Use your palm to touch the lock sensor. Before driving Door lock buzzer If an attempt to lock the doors is made when a door is not fully closed, a buzzer sounds continuously. Fully close the door to stop the buzzer, and lock the vehicle once more.
1-2. Opening, closing and locking the doors and trunk Alarm Situation Correction procedure An attempt was made to lock the doors using the smart entry & start system while the electronic key was still inside the vehicle. Retrieve the electronic key from the vehicle and lock the doors again. An attempt was made to lock the vehicle while a door was open. Close all of the doors and lock the doors again.
1-2. Opening, closing and locking the doors and trunk Battery-saving function The battery-saving function will be activated in order to prevent the electronic key battery and the vehicle battery from being discharged while the vehicle is not in operation for a long time. In the following situations, the smart entry & start system may take some time to unlock the doors. 1 Before driving • The electronic key has been left in an area of approximately 2 m (6 ft.
1-2. Opening, closing and locking the doors and trunk Conditions affecting operation The smart entry & start system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart entry & start system, wireless remote control and engine immobilizer system from operating properly. (Way of coping P.
1-2. Opening, closing and locking the doors and trunk Notes for the entry function Even when the electronic key is within the effective range (detection areas), the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked. • The electronic key is near the ground or in a high place, or too close to the rear bumper center when the trunk is unlocked.
1-2. Opening, closing and locking the doors and trunk Notes for locking the doors Touching the door lock sensor while wearing gloves may delay or prevent lock operation. Remove the gloves and touch the lock sensor again. Vehicles without a double locking system: When the lock operation is performed using the lock sensor, recognition signals will be shown up to two consecutive times. After this, no recognition signals will be given.
1-2. Opening, closing and locking the doors and trunk When the vehicle is not driven for extended periods To prevent theft of the vehicle, do not leave the electronic key within 2 m (6 ft.) of the vehicle. The smart entry & start system can be deactivated in advance. (P. 430) To operate the system properly 1 Before driving Make sure to carry the electronic key when operating the system.
1-2. Opening, closing and locking the doors and trunk Electronic key battery depletion The standard battery life is 1 to 2 years. If the battery becomes low, an alarm will sound in the cabin when the engine stops. (P. 367) As the electronic key always receives radio waves, the battery will become depleted even if the electronic key is not used. The following symptoms indicate that the electronic key battery may be depleted. Replace the battery when necessary. (P.
1-2.
1-2.
1-2. Opening, closing and locking the doors and trunk 1 Before driving -Replace only with the same or equivalent type recommended by the manufacturer. -Dispose of used batterites according to the local laws. Hereby, DENSO CORPORATION declares that this 13CZY/14AER is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
1-2. Opening, closing and locking the doors and trunk CAUTION Caution regarding interference with electronic devices People with implanted pacemakers or cardiac defibrillators should maintain a reasonable distance between themselves and the smart entry & start system antennas. (P. 33) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled.
1-2. Opening, closing and locking the doors and trunk Wireless remote control The wireless remote control can be used to lock and unlock the vehicle. Vehicles without a smart entry & start system Locks both side doors*1 Locks driver’s door*2 1 Before driving Unlocks both side doors*1 Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors.
1-2. Opening, closing and locking the doors and trunk Operation signals The emergency flashers flash to indicate that the doors have been locked/ unlocked. (Locked: Once; Unlocked: Twice) Door lock buzzer (vehicles with a smart entry & start system) If an attempt to lock the doors is made when a door is not fully closed, a buzzer sounds continuously. Fully close the door to stop the buzzer, and lock the vehicle once more.
1-2. Opening, closing and locking the doors and trunk If the wireless remote control does not operate properly (vehicles with a smart entry & start system) Locking and unlocking the doors, unlocking the trunk: Use the mechanical key. (P. 399) Key battery depletion 1 Before driving Vehicles without a smart entry & start system If the wireless remote control function does not operate, the battery may be depleted. Replace the battery when necessary. (P.
1-2. Opening, closing and locking the doors and trunk Doors The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. Entry function (vehicles with a smart entry & start system) P. 32 Wireless remote control P. 47 Key Turning the key operates the doors as follows: Vehicles without a smart entry & start system Locks both side doors*1 Locks driver’s door*2 Unlocks both side doors*1 Turning the key unlocks the driver’s door.
1-2. Opening, closing and locking the doors and trunk Door lock switch Locks both side doors Unlocks both side doors 1 Before driving Inside lock button Locks the door Unlocks the door Locking the doors from the outside without a key STEP 1 Move the inside lock button to the lock position. STEP 2 Close the door while pulling the door handle.
1-2. Opening, closing and locking the doors and trunk Window open/close function linked to door operation In order to make opening and closing the doors easier, completely closed windows are linked to door operations. Therefore, when a door is opened, its window opens slightly. When a door is closed, its window closes completely. However, if the battery has discharged or is disconnected, this function will not operate. (P.
1-2. Opening, closing and locking the doors and trunk Trunk The trunk can be opened using the key, trunk opener, entry function or wireless remote control. Opening the trunk from inside the vehicle Press and hold the opener switch to release the trunk lid. 1 Before driving Opening the trunk from outside the vehicle Key (vehicles without a smart entry & start system and the double locking system) Turn the master key clockwise to release the trunk lid.
1-2. Opening, closing and locking the doors and trunk Function to prevent the trunk being locked with the electronic key inside (vehicles with a smart entry & start system) When all doors are being locked, closing the trunk lid with the electronic key left inside the trunk will sound an alarm. In this case, the trunk lid can be opened using the entry function.
1-2. Opening, closing and locking the doors and trunk CAUTION Caution while driving Keep the trunk lid closed while driving. If the trunk lid is left open, it may hit near-by objects while driving or luggage in the trunk may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a serious health hazard. Make sure to close the trunk lid before driving.
1-2. Opening, closing and locking the doors and trunk CAUTION Using the trunk Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in serious injury. Remove any heavy loads, such as snow and ice, from the trunk lid before opening it. Failure to do so may cause the trunk lid to fall closed again after it is opened. When opening or closing the trunk lid, thoroughly check to make sure the surrounding area is safe.
1-2. Opening, closing and locking the doors and trunk NOTICE Trunk damper stays The trunk lid is equipped with damper stays that hold the trunk lid in place. Observe the following precautions. Failure to do so may cause damage to trunk damper stays, resulting in a malfunction. 1 Before driving Do not attach any foreign objects such as stickers, plastic sheets and adhesives to damper stay rods. Do not touch damper stay rods with gloves or other fabric items.
1-3.
1-3. Adjustable components (seats, mirrors, steering wheel) Getting in and out of the rear seats To get in and out of the rear seats, use the seatback angle adjustment lever or seatback fold strap. 1 Before getting in or out of the rear seats Release the seat belt from the seat belt guide. (P. 67) Before driving Getting in the rear seats Driver’s side (if equipped) Lift the seatback angle adjustment lever. The seatback will fold forward. Passenger’s side Lift the seatback angle adjustment lever.
1-3. Adjustable components (seats, mirrors, steering wheel) Getting out of the rear seats Driver’s side (if equipped) Pull the seatback fold strap. The seatback will fold forward. Passenger’s side Pull the seatback fold strap. The seatback will fold forward. The seat can be slid forward and backward. After getting in or out of the rear seats Return the seatback to the upright position until the seat locks.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Seat adjustment To reduce the risk of sliding under the lap belt during a collision, do not recline the seat more than necessary. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen, or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident.
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats The seatbacks of the rear seats can be folded down. Press the seatback lock release buttons and fold the seatback down. Press the button until the lock is released. To return the seatbacks to its original position, lift it up until it locks. Seat dust cover Always remove the seat dust cover that may be attached at the time of purchase before using the seat.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION After returning the rear seatback to the upright position Observe the following precautions. Failure to do so may result in death or serious injury. 1 Before driving Make sure that the seatback is securely locked in position by lightly pushing it back and forth. If the seatback is not securely locked, the red portion behind the seatback lock release button will be visible. Make sure that the red portion is not visible.
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Up Pull the head restraints up. Down Push the head restraint down while pushing the lock release button. Lock release button Removing the head restraints Pull the head restraint up while pushing the lock release button. Installing the head restraints Align the head restraint with the installation holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.
1-3. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. 1 Before driving CAUTION Head restraint precautions Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. Use head restraints designed for each respective seat.
1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driving the vehicle. Correct use of the seat belts Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoulder. Position the lap belt as low as possible over the hips. Adjust the position of the seatback. Sit up straight and well back in the seat. Do not twist the seat belt.
1-3. Adjustable components (seats, mirrors, steering wheel) Front seat belt guide To enable the seat belt to be easily extended, pass the seat belt through the guide. 1 Before driving When getting in or out of the rear seats, release the seat belt from the guide. Seat belt pretensioners (front seats) The pretensioner helps the seat belt to quickly restrain the occupant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal collision.
1-3. Adjustable components (seats, mirrors, steering wheel) Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully. Child seat belt usage The seat belts of your vehicle are principally designed for persons of adult size.
1-3. Adjustable components (seats, mirrors, steering wheel) Replacing the belt after the pretensioner has been activated If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent collisions.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Pregnant women Obtain medical advice and wear the seat belt in the proper way. (P. 66) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occupants. Extend the shoulder belt completely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Seat belt pretensioners If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. 1 Before driving To obtain maximum protection, the occupants should sit in an upright position with their seat belts properly fastened.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. Inappropriate handling of the pretensioner may prevent it from operating properly, resulting in death or serious injury.
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. STEP 1 Hold the steering wheel and push the lever down. 1 Before driving STEP 2 Adjust to the ideal position by moving the steering wheel horizontally and vertically. After adjustment, pull the lever up to secure the steering wheel. CAUTION Caution while driving Do not adjust the steering wheel while driving.
1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror The rear view mirror’s position can be adjusted to enable sufficient confirmation of the rear view in accordance with the driver's seating posture. Adjusting the height of rear view mirror Adjust the height of the rear view mirror by moving it up and down. Anti-glare function Reflected light from the headlights of vehicles behind can be reduced by operating the lever.
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted using the switch. STEP 1 Select a mirror to adjust. Left 1 Right Before driving STEP 2 Adjust the mirror.
1-3. Adjustable components (seats, mirrors, steering wheel) Folding the mirrors Manual operation Push the mirror back in the direction of the vehicle’s rear. Power operation (if equipped) Press the switch to fold the mirrors. Press it again to extend them to the original position. The mirrors can be adjusted when Vehicles without a smart entry & start system The engine switch is in the “ACC” or “ON” position.
1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION When driving the vehicle Observe the following precautions while driving. Failure to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury. 1 Do not adjust the mirrors while driving. Before driving Do not drive with the mirrors folded. Both the driver and passenger side mirrors must be extended and properly adjusted before driving.
1-4. Opening and closing the windows Power windows The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows: Closing One-touch closing* Opening One-touch opening* *: Pushing the switch in the opposite direction will stop window travel partway. Window lock switch Press the switch down to lock the passenger window glasses. Use this switch to prevent children from accidentally opening or closing a passenger window.
1-4. Opening and closing the windows The power windows can be operated when Vehicles without a smart entry & start system The engine switch is in the “ON” position. Vehicles with a smart entry & start system The “ENGINE START STOP” switch is in IGNITION ON mode.
1-4. Opening and closing the windows When the power window does not close normally If the jam protection function is operating abnormally and a window cannot be closed, close all the doors and perform the following operations using the power window switch on the relevant door. STEP 1 Vehicles without a smart entry & start system: After stopping the vehicle, the engine switch is turned to the “ON” position.
1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap: Before refueling the vehicle Vehicles without a smart entry & start system: Turn the engine switch off and ensure that all the doors and windows are closed. 1 Before driving Vehicles with a smart entry & start system: Turn the “ENGINE START STOP” switch off and ensure that all the doors and windows are closed. Confirm the type of fuel. (P.
1-5. Refueling STEP 3 Hang the fuel tank cap on the back of the fuel filler door. Closing the fuel tank cap After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.
1-5. Refueling CAUTION Refueling the vehicle Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. 1 Do not handle fuel indoors. Before driving After exiting the vehicle and before opening the fuel door, touch an unpainted metal surface to discharge any static electricity. It is important to discharge static electricity before refueling because sparks resulting from static electricity can cause fuel vapors to ignite while refueling.
1-5. Refueling CAUTION When refueling Observe the following precautions to prevent fuel overflowing from the fuel tank: Securely insert the fuel nozzle into the fuel filler neck. Stop filling the tank after the fuel nozzle automatically clicks off. Do not top off the fuel tank. Observe other precautions that are posted at the service station. Turn the cap to the right until it clicks to ensure that it is fully tightened.
1-6. Theft deterrent system Engine immobilizer system The vehicle's keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle's on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. 1 Before driving Vehicles without a smart entry & start system The indicator light flashes after the key has been removed from the engine switch to indicate that the system is operating.
1-6. Theft deterrent system When the vehicle cannot be started with the registered key (vehicles without a smart entry & start system) Remove the key and try again. System maintenance The vehicle has a maintenance-free type engine immobilizer system.
1-6.
1-6.
1-6.
1-6. Theft deterrent system Hereby, Tokai Rika Co., Ltd., declares that this RI-38BFH is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
1-6. Theft deterrent system NOTICE To ensure the system operates correctly Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
1-6. Theft deterrent system Double locking system Unauthorized access to the vehicle is prevented by disabling the door unlocking function from both the interior and exterior of the vehicle. Vehicles employing this system have labels on the window glass of both front doors. Setting the double locking system Vehicles without a smart entry & start system: Turn the engine switch off, have all the passengers exit the vehicle and ensure that all the doors are closed.
1-6. Theft deterrent system CAUTION Double locking system precaution Never activate the double locking system when there are people in the vehicle because all the doors cannot be opened from inside the vehicle.
1-7. Safety information Correct driving posture Drive with a good posture as follows: Sit upright and well back in the seat. (P. 58) Adjust the position of the seat forward or backward to ensure the pedals can be reached and easily depressed to the extent required. (P. 58) Adjust the seatback so that the controls are easily operable. (P. 58) Adjust the tilt and telescopic positions of the steering wheel to allow easy operation and to ensure the airbag is facing your chest. (P.
1-7. Safety information CAUTION While driving Do not adjust the position of the driver's seat. Doing so could cause the driver to lose control of the vehicle. 1 Before driving Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger. Do not place anything under the front seats.
1-7. Safety information SRS airbag (Supplemental Restraint System airbag) The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. SRS: This stands for supplemental restraint system. This name is used because the airbag system supplements the vehicle’s seat belts.
1-7. Safety information Front airbags for driver and front passenger Knee airbag for driver Side airbags for driver and front passenger Curtain shield airbags for driver, front passenger and windowside rear passengers 1 Before driving These SRS airbags are designed only as a supplement to the primary protection provided by the seat belt. The system also controls front seat belt pretensioners.
1-7. Safety information CAUTION SRS airbag To obtain maximum protection in the event of an accident, the driver and all passengers in the vehicle should always wear seat belts when the vehicle is moving. The SRS airbag is designed only to be a supplement to the primary protection provided by the seat belt. It does not eliminate the need to fasten seat belts. In combination with the seat belts, it offers the best combined protection in case of a serious accident.
1-7. Safety information CAUTION SRS airbag Put children in the REAR seat properly restrained at all times in a child restraint device or in a seat belt, whichever is appropriate for the child’s age, height and weight. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are not restrained or improperly restrained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater.
1-7. Safety information NOTICE When the SRS airbag deploys When the SRS airbag deploys, some smoke will be released. This smoke could cause breathing problems for people with a history of asthma or other breathing trouble. If you or your passengers have breathing problems after SRS airbag deploys, get fresh air promptly.
1-7.
1-7. Safety information Door impact sensor (lefthand side) Front sub sensor (left-hand side) Driver’s knee airbag module Curtain shield airbag module (left-hand side) Airbag control module (including impact sensors) The main SRS airbag system components are shown above. The SRS airbag system is controlled by the airbag control module. The airbag control module consists of an airbag sensor. In certain types of severe front or side impacts, the SRS airbag system triggers the airbag inflators.
1-7. Safety information SRS front airbag The driver’s SRS front airbag is stowed in the center portion of the steering wheel. The driver’s knee airbag is stowed under the steering column. The passenger’s SRS front airbag is stowed near the top of the dashboard under an “SRS AIRBAG” mark. 1 In a moderate to severe front collision, the following components deploy.
1-7.
1-7. Safety information Operation Driver's side SRS AIRBAGs deploy as soon as a collision occurs. After deployment, SRS AIRBAGs start to deflate immediately so that the driver’s vision is not obstructed. 1 Before driving *: Models with knee airbag Passenger’s side SRS AIRBAGs deploy as soon as a collision occurs. After deployment, SRS AIRBAGs start to deflate immediately so that the driver's vision is not obstructed.
1-7. Safety information The SRS airbag can function only when the engine switch is in the “ON” position (vehicles without a smart entry & start system) or when the “ENGINE START STOP” switch is in IGNITION ON mode (vehicles with a smart entry & start system).
1-7. Safety information The SRS front airbag (and also the knee airbag) is designed to deploy in the event of an accident involving a moderate to severe front collision. It is not designed to deploy in most lesser front impacts because the necessary protection can be achieved by the seat belt alone. Also, it is not designed to deploy in most side or rear impacts or in most roll-over accidents because deployment of the SRS front airbag would not help the occupant in those situations.
1-7. Safety information When is the SRS front airbag unlikely to deploy? The vehicle strikes an object, such as a telephone pole or sign pole. The vehicle slides under the load bed of a truck. The vehicle sustains an oblique offset front impact. The vehicle sustains an offset front collision.
1-7. Safety information The vehicle strikes an object that can move or deform, such as a parked vehicle. 1 Before driving There are many types of collisions which might not necessarily require SRS front airbag deployment. In the event of accidents like those illustrated, the SRS front airbag may not deploy depending on the level of accident forces involved.
1-7. Safety information First impact Second impact In an accident where the vehicle is impacted more than once, the SRS front airbag deploys only once on the first impact. Example: In the case of a double collision, first with another vehicle, then against a concrete wall in immediate succession, once the SRS front airbag is activated on the first impact, it will not be activated on the second. CAUTION A warning label A warning label as shown above is attached to the sun visor.
1-7. Safety information SRS side airbag and SRS curtain shield airbag The SRS side airbag is stored in the door side of each front seat seatback, which bears an “SRS AIRBAG” label. The curtain shield airbag on each side of the cabin is stored in the roof side (between the front pillar and a point over the rear seat). An “SRS AIRBAG” mark is located at the top of each center pillar.
1-7. Safety information The driver’s and front passenger’s SRS side airbags and SRS curtain shield airbags deploy independently of each other since each has its own impact sensor. Therefore, they may not both deploy in the same accident. Also, the SRS side airbag and SRS curtain shield airbag deploy independently of the driver’s and front passenger’s SRS front airbags in the steering wheel and instrument panel.
1-7. Safety information When the SRS side airbag and SRS curtain shield airbag deploy, a sudden, fairly loud inflation noise will be heard and some smoke will be released. These occurrences are a normal result of the deployment. This smoke does not indicate a fire in the vehicle. The SRS side airbag and SRS curtain shield airbag are designed to deploy in the event of an accident involving a moderate to severe side impact collision. They are not designed to deploy in most lesser side impact.
1-7. Safety information The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment. The vehicle strikes a telephone pole or similar object. The vehicle is involved in a side-on impact from a motorcycle. The vehicle rolls onto its side or roof. There are many types of collisions which might not necessarily require SRS side airbag and SRS curtain shield airbag deployment.
1-7. Safety information When will the SRS side airbag and SRS curtain shield airbag not deploy? The vehicle is involved in front collision with another vehicle (moving or stationary). 1 Before driving The vehicle is struck from behind. The SRS side airbag and SRS curtain shield airbag are not designed to deploy in most cases if the vehicle is involved in a front collision or is struck from behind. Examples of such accidents are illustrated.
1-7. Safety information When to contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional In the following cases, the vehicle will require inspection and/or repair. Contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional as soon as possible. Any of the SRS airbags have been inflated.
1-7. Safety information The portion of the front pillars, rear pillars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked or otherwise damaged. 1 Before driving CAUTION If the SRS airbags deploy Do not touch the SRS side airbag system components around the front seat seatback with bare hands right after deployment. Doing so can cause burns because the components can be very hot as a result of deployment.
1-7. Safety information CAUTION SRS airbag precautions • Slightly recline the back of the seat. Although vehicle designs vary, many drivers can achieve the 250 mm (10 in.) distance, even with the driver seat all the way forward, simply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that feature. • If your steering wheel is adjustable, tilt it downward.
1-7. Safety information CAUTION SRS airbag precautions Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger. 1 Before driving Do not allow the front seat occupants to hold items on their knees. Do not lean against the door, the roof side rail or the front, side and rear pillars. Do not allow anyone to kneel on the passenger seat toward the door or put their head or hands outside the vehicle.
1-7. Safety information CAUTION SRS airbag precautions Do not attach anything to areas such as a door, windshield glass, side door glass, rear quarter glass, front or rear pillar, roof side rail and assist grip. (Except for the speed limit label P. 383) Vehicles without a smart entry & start system only: Do not attach any heavy, sharp or hard objects such as keys and accessories to the key.
1-7. Safety information CAUTION SRS airbag precautions If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. 1 Before driving The SRS side airbag and SRS curtain shield airbag are designed only to be a supplement to the primary protection provided by the seat belt.
1-7. Safety information SRS airbag system monitor SRS warning light A diagnostic system continually monitors the readiness of the SRS airbag system (including front seat belt pretensioners) while the vehicle is being driven.
1-7.
1-7. Safety information CAUTION SRS warning light If the warning light exhibits any of the following conditions, there may be a malfunction in the seat belt pretensioners and/or SRS airbag system. We recommend that you have the system checked immediately by your nearest any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. Unless checked and properly repaired, the seat belt pretensioners and/or SRS airbags will operate improperly (e.g.
1-7. Safety information Child restraint systems Toyota strongly urges the use of child restraint systems. Points to remember 1 Before driving Studies have shown that installing a child restraint on a rear seat is safer than installing one to the front passenger seat. Choose a child restraint system appropriate to the age and size of the child. For installation details, follow the instructions provided with the child restraint system. General installation instructions are provided in this manual.
1-7. Safety information Baby seat Equal to Group 0 and 0+ of ECE No.44 Child seat Equal to Group 0+ and I of ECE No.44 Junior seat Equal to Group II and III of ECE No.
1-7. Safety information Child restraint system suitability for various seating positions Provided information in the table shows your child restraint system suitability for various seating positions. 1 Seating position Front passenger seat Mass groups Rear seat ON OFF 0 (up to 10 kg [22 lb.]) X Never put L3, L4 X 0+ (up to 13 kg [28 lb.]) X Never put L3, L4 X L1 U L2, L5 U, L2 I (9 to 18 kg [20 to 39 lb.]) II, III (15 to 36 kg [34 to 79 lb.
1-7. Safety information Note When you use child restraint system on the front passenger seat, you must turn off the airbag manual on-off switch. Key of letters inserted in the above table: U: Suitable for “universal” category child restraint system approved for the use in this mass group. L1: Suitable for “TOYOTA DUO+” (9 to 18 kg [20 to 39 lb.]) approved for the use in this mass group. L2: Suitable for “TOYOTA KID FIX” (15 to 36 kg [34 to 79 lb.]) approved for the use in this mass group.
1-7. Safety information Child restraint system suitability for various seating positions (with ISOFIX rigid anchors) Provided information in the table shows your child restraint system suitability for various seating positions. Vehicle ISOFIX positions Fixture F ISO/L1 X G ISO/L2 X (1) X ISO/R1 X (1) X E ISO/R1 X D ISO/R2 X C ISO/R3 X (1) X D ISO/R2 X C ISO/R3 X B ISO/F2 IUF B1 ISO/F2X IUF A ISO/F3 X (1) X II (15 to 25 kg [34 to 55 lb.
1-7. Safety information (1) For the CRS which do not carry the ISO/XX size class identification (A to G), for the applicable mass group, the car manufacturer shall indicate the vehicle specific ISOFIX child restraint system(s) recommended for each position. Key of letters inserted in the above table: IUF: Suitable for ISOFIX forward child restraint systems of universal category approved for use in this mass group.
1-7. Safety information When installing the child restraint system on the front passenger seat When you have to use a child restraint system on the front passenger seat, adjust the following: 1 The seat cushion to the fully rearward position Before driving The seatback to the most upright position Selecting an appropriate child restraint system Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the vehicle’s seat belt.
1-7. Safety information CAUTION Child restraint precautions Never use a rear-facing child restraint system on the front passenger seat when the airbag manual on-off switch is on. (P. 148) In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child. A forward-facing child restraint system should be allowed to be installed on the front passenger seat only when it is unavoidable.
1-7. Safety information Installing child restraints Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the rear seats using a seat belt or a ISOFIX rigid anchors. Attach the top strap when installing a child restraint. Installation with a seat belt (P. 134) 1 Before driving ISOFIX rigid anchors (ISOFIX child restraint system) Lower anchors are provided for the both rear seats. (Buttons displaying the location of the anchors are attached to the seats.
1-7. Safety information Installing child restraints using a seat belt Rear facing Baby seat/child seat STEP 1 Place the child restraint system on the rear seat facing the rear of the vehicle. STEP 2 Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted. Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place.
1-7. Safety information Forward facing Child seat STEP 1 Place the child restraint system on the seat facing the front of the vehicle. 1 Before driving STEP 2 Run the seat belt through the child restraint system and insert the plate into the buckle. Make sure that the belt is not twisted. Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place.
1-7. Safety information Junior seat STEP 1 Place the child restraint system on the seat facing the front of the vehicle. STEP 2 Sit the child in the child restraint system. Fit the seat belt to the child restraint system according to the manufacturer's instructions and insert the plate into the buckle. Make sure that the belt is not twisted. Check that the shoulder belt is correctly positioned over the child's shoulder and that the lap belt is as low as possible. (P.
1-7. Safety information Removing a child restraint installed with a seat belt Push the buckle release button and fully retract the seat belt. 1 Before driving Installation with ISOFIX rigid anchor (ISOFIX child restraint system) Latch the buckles onto the exclusive fixing bars. If the child restraint has a top strap, the top strap should be latched onto the anchor bracket.
1-7. Safety information Child restraint systems with a top strap STEP 1 STEP 2 Secure the child restraint using a seat belt or ISOFIX rigid anchor. Remove cover. the anchor bracket Store the removed cover in a safe place. STEP 3 Latch the hook onto the anchor bracket and tighten the top strap. Make sure the top strap is securely latched.
1-7. Safety information When installing a child restraint system (without a lock-off) using a seat belt You need a locking clip to install the child restraint system using a seat belt. Follow the instructions provided by the manufacturer of the system. If your child restraint system does not provide a locking clip, you can purchase the following item from any authorized Toyota dealer or repairer, or another duly qualified and equipped professional.
1-7. Safety information CAUTION When installing a child restraint system Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be injured or even killed in the event of sudden braking, sudden swerving or an accident.
1-7. Safety information CAUTION When installing a child restraint system Never use a rear-facing child restraint system on the front passenger seat when the airbag manual on-off switch is on. (P. 148) 1 Before driving The force of the rapid inflation of the front passenger airbag can cause death or serious injury to children in the event of an accident.
1-7.
1-7.
1-7.
1-7.
1-7.
1-7. Safety information CAUTION When installing a child restraint system If child restraint system regulations exist in the country where you reside, please contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional for the child restraint system installation. 1 Before driving When a junior seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder.
1-7. Safety information Airbag manual on-off system This system deactivates the front passenger airbag and front passenger side airbag. Only deactivate the airbags when using a child restraint system on the front passenger seat. Airbag manual on-off indicator Vehicles without a smart entry & start system This indicator light turns on when the airbag system is on (only when the engine switch is in the “ON” position).
1-7. Safety information Deactivating the front seat passenger airbag and front passenger side airbag Vehicles without a smart entry & start system 1 Before driving Insert the key into the cylinder and turn to the “OFF” position. The “OFF” indicator light turns on (only when the engine switch is in the “ON” position). Vehicles with a smart entry & start system Insert the mechanical key into the cylinder and rotate to the “OFF” position.
1-7. Safety information CAUTION When installing a child restraint system For safety reasons, always install a child restraint system in a rear seat. In the event that the rear seat cannot be used, the front seat can be used as long as the airbag manual on-off system is set to “OFF”. If the airbag manual on-off system is left on, the strong impact of the airbag deployment (inflation) may cause serious injury or even death.
When driving 2-1. Driving procedures Driving the vehicle ............ Engine (ignition) switch (vehicles with a smart entry & start system)....... Engine (ignition) switch (vehicles without a smart entry & start system)....... Automatic transmission .... Manual Transmission ....... Turn signal lever ............... Parking brake ................... Horn.................................. 152 165 2 2-4. Using other driving systems Cruise control.................... 217 Driving assist systems ......
2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driving: Starting the engine P. 165, 174 Driving Vehicles with an automatic transmission STEP 1 With the brake pedal depressed, shift the shift lever to D. (P. 177) STEP 2 Release the parking brake. (P. 188) STEP 3 Gradually release the brake pedal and gently depress the accelerator pedal to accelerate the vehicle.
2-1. Driving procedures Parking the vehicle Vehicles with an automatic transmission STEP 1 With the shift lever in D, depress the brake pedal. STEP 2 Shift the shift lever to P. (P. 177) STEP 3 Set the parking brake. (P. 188) STEP 4 Vehicles without a smart entry & start system: Turn the engine switch to the “LOCK” position to stop the engine. 2 STEP 5 When driving Vehicles with a smart entry & start system: Press the “ENGINE START STOP” switch to stop the engine.
2-1. Driving procedures Starting off on a steep uphill Vehicles with an automatic transmission STEP 1 Make sure that the parking brake is set and shift the shift lever to D. STEP 2 Gently depress the accelerator pedal. STEP 3 Release the parking brake. Vehicles with a manual transmission STEP 1 With the parking brake firmly set and the clutch pedal fully depressed, shift the shift lever to 1. STEP 2 Lightly depress the accelerator pedal at the same time as gradually releasing the clutch pedal.
2-1. Driving procedures New vehicle break-in driving (the first 1600 km [1000 miles]) The performance and long life of your vehicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1600 km (1000 miles): Do not allow the engine speed to exceed 4000 rpm except in an emergency. Do not drive at one constant engine or vehicle speed for a long time, either fast or slow.
2-1. Driving procedures REV indicator (if equipped) When the set engine speed is reached the REV indicator comes on and a buzzer sounds to inform the driver. (P. 202) (When the engine speed enters the red zone, the REV indicator flashes regardless of settings.) CAUTION When starting the vehicle (vehicles with an automatic transmission) Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.
2-1. Driving procedures CAUTION On vehicles with an automatic transmission, do not let the vehicle roll backward while the shift lever is in a driving position, or roll forward while the shift lever is in R. Doing so may cause the engine to stall or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle. If the smell of exhaust is noticed inside the vehicle, open the windows and check that the trunk is closed.
2-1. Driving procedures CAUTION Use engine braking (downshift) to maintain a safe speed when driving down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (P. 178, 184) Do not adjust the position of the steering wheel, the seat, or the inside or outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents, resulting in death or serious injury.
2-1. Driving procedures CAUTION If you hear a squealing or scraping noise (brake pad wear indicators) Have the brake pads checked and replaced by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional as soon as possible. Rotor damage may result if the pads are not replaced when needed. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or those of the brake discs are exceeded.
2-1. Driving procedures CAUTION When the vehicle is parked Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in the vehicle when it is in the sun. Doing so may result in the following: • Gas may leak from a cigarette lighter or spray can, and may lead to a fire. • The temperature inside the vehicle may cause the plastic lenses and plastic material of glasses to deform or crack.
2-1. Driving procedures CAUTION Exhaust gases Exhaust gases include harmful carbon monoxide (CO), which is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health hazard. If the vehicle is in a poorly ventilated area, stop the engine. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard. 2 When driving The exhaust system should be checked occasionally.
2-1. Driving procedures CAUTION When braking When the brakes are wet, drive more cautiously. Braking distance increases when the brakes are wet, and this may cause one side of the vehicle to brake differently than the other side. Also, the parking brake may not securely hold the vehicle. If the power brake assist function does not operate, do not follow other vehicles closely and avoid hills or sharp turns that require braking.
2-1. Driving procedures NOTICE When driving the vehicle Vehicles with an automatic transmission Do not depress the accelerator and brake pedals at the same time during driving, as this may restrain driving torque. Do not use the accelerator pedal or depress the accelerator and brake pedals at the same time to hold the vehicle on a hill. Vehicles with a manual transmission Do not depress the accelerator and brake pedals at the same time during driving, as this may restrain driving torque.
2-1. Driving procedures NOTICE Avoiding damage to vehicle parts Do not turn the steering wheel fully in either direction and hold it there for an extended period of time. Doing so may damage the power steering motor. When driving over bumps in the road, drive as slowly as possible to avoid damaging the wheels, underside of the vehicle, etc.
2-1. Driving procedures Engine (ignition) switch (vehicles with a smart entry & start system) Performing the following operations when carrying the electronic key on your person starts the engine or changes “ENGINE START STOP” switch modes. Starting the engine Vehicles with an automatic transmission STEP 1 Check that the parking brake is set. STEP 2 Check that the shift lever is set in P. If the shift lever is not set in P, the engine may not be started. (P. 177) Firmly depress the brake pedal.
2-1. Driving procedures Vehicles with a manual transmission STEP 1 Check that the parking brake is set. STEP 2 Check that the shift lever is set in N. STEP 3 Firmly depress the clutch pedal. The smart entry & start system indicator light (green) will turn on. If the indicator light does not turn on, the engine cannot be started. STEP 4 Press the “ENGINE START STOP” switch. The engine will crank until it starts or for up to 10 seconds, whichever is less.
2-1. Driving procedures Stopping the engine Vehicles with an automatic transmission STEP 1 Stop the vehicle. STEP 2 Shift the shift lever to P. STEP 3 Set the parking brake. (P. 188) STEP 4 Release the brake pedal. STEP 5 Press the “ENGINE START STOP” switch. STEP 6 Check that the smart entry & start system indicator light (green) is off. 2 When driving Vehicles with a manual transmission STEP 1 While depressing the clutch pedal, stop the vehicle. STEP 2 Shift the shift lever to N.
2-1. Driving procedures Changing “ENGINE START STOP” switch mode Modes can be changed by pressing the “ENGINE START STOP” switch with the brake pedal (vehicles with an automatic transmission) or clutch pedal (vehicles with a manual transmission) released. (The mode changes each time the switch is pressed.) Off* The emergency flashers can be used. The smart entry & start system indicator light (green) is off. ACCESSORY mode Some electrical components such as the power outlet can be used.
2-1. Driving procedures When stopping the engine with the shift lever in a position other than P (vehicles with an automatic transmission) If the engine is stopped with the shift lever in a position other than P, the “ENGINE START STOP” switch will not be turned off but instead be turned to ACCESSORY mode. Perform the following procedure to turn the switch off: Check that the parking brake is set. STEP 2 Shift the shift lever to P.
2-1. Driving procedures Operation of the “ENGINE START STOP” switch When operating the “ENGINE START STOP” switch, one short, firm press is enough. If the switch is pressed improperly, the engine may not start or the “ENGINE START STOP” switch mode may not change. It is not necessary to press and hold the switch. Electronic key battery depletion P. 42 Conditions affecting operation P. 38 Note for the entry function P.
2-1. Driving procedures When the steering lock cannot be released The smart entry & start system indicator light (green) will flash quickly. Vehicles with an automatic transmission Check that the shift lever is set in P. Press the “ENGINE START STOP” switch while turning the steering wheel left and right. Vehicles with a manual transmission 2 When driving Press the “ENGINE START STOP” switch while turning the steering wheel left and right.
2-1. Driving procedures CAUTION When starting the engine Always start the engine while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury. If the smart entry & start system indicator light flashes in green after the engine has started, never drive the vehicle. The steering wheel is still locked, and it may result in an accident.
2-1. Driving procedures NOTICE To prevent battery discharge Do not leave the “ENGINE START STOP” switch in ACCESSORY or IGNITION ON mode for long periods of time without the engine running. If the smart entry & start system indicator light (green) is illuminated, the “ENGINE START STOP” switch is not off. When exiting the vehicle, always check that the “ENGINE START STOP” switch is off.
2-1. Driving procedures Engine (ignition) switch (vehicles without a smart entry & start system) Starting the engine Vehicles with an automatic transmission STEP 1 Check that the parking brake is set. STEP 2 Check that the shift lever is set in P. STEP 3 Firmly depress the brake pedal. STEP 4 Turn the engine switch to the “START” position to start the engine. Vehicles with a manual transmission STEP 1 Check that the parking brake is set. STEP 2 Check that the shift lever is set in N.
2-1. Driving procedures Turning the key from “ACC” to “LOCK” STEP 1 Shift the shift lever to N (manual transmission) or P (automatic transmission). (P. 177, 184) STEP 2 Push in the key and turn to the “LOCK” position. 2 When driving If the engine does not start The engine immobilizer system may not have been deactivated. (P. 85) Contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional.
2-1. Driving procedures CAUTION When starting the engine Always start the engine while sitting in the driver's seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury. Caution when driving Do not turn the engine switch to the “LOCK” position while driving.
2-1. Driving procedures Automatic transmission Select a shift position appropriate for the driving conditions. Shifting the shift lever 2 When driving Vehicles without a smart entry & start system While the engine switch is in the “ON” position, move the shift lever with the brake pedal depressed. When shifting the shift lever between P and D, make sure that the vehicle is completely stopped.
2-1. Driving procedures Shift position uses Shift position Meter display Function P Parking the vehicle/starting the engine R Reversing N Neutral Normal D position driving* (gears between “1” and “6” are automatically selected) D (paddle shift switches activated) M Temporary manual mode driving (P. 182) Manual mode driving (P. 180) *: Shifting to the D position allows the system to select a gear suitable for the driving conditions.
2-1. Driving procedures Selecting a driving mode By pressing the driving pattern selector switch the following modes can be selected to suit driving and usage conditions: 2 When driving Normal mode Sport mode The “SPORT” indicator comes on. Use sport mode for sporty driving or when driving in mountainous regions with lots of curves. Snow mode The “SNOW” indicator comes on. Use snow mode for accelerating and driving on slippery road surfaces such as snow.
2-1. Driving procedures Manual mode driving To enter manual mode, shift the shift lever to the M position. While the upshift/downshift indicator light is illuminated, gears can be selected by operating the shift lever or paddle shift switches (if equipped), allowing you to drive in the gear of your choosing. Even if upshifting operations are performed, if vehicle speed is too low for the requested gear, the gear will not change.
2-1. Driving procedures When moving the shift lever out of P If the shift lever is pushed sideways before the brake pedal is depressed, shift lever operation may not be possible. Depress the brake pedal before shifting the shift lever out of P.
2-1. Driving procedures Automatic gear selection when the vehicle is stopped When the vehicle is idling at high rpm in order to warm up, and the vehicle is on a slippery road, the transmission may automatically shift to 2nd gear for stopping and starting off. Temporary manual mode driving (vehicles with paddle shift switches) Temporary manual mode driving can be changed to by operating the paddle shift switches while the shift lever is in the D position.
2-1. Driving procedures AI-SHIFT The AI-SHIFT automatically shifts the gear to the suitable position according to the driver performance and driving conditions. The AI-SHIFT automatically operates when the shift lever is in the D position. (Operating the paddle shift switches or shifting the shift lever to the M position cancels the function.
2-1. Driving procedures Manual Transmission Shifting the shift lever Fully depress the clutch pedal before operating the shift lever, and then release it slowly. Shifting the shift lever to R Shift the shift lever to R while lifting up the ring section.
2-1. Driving procedures Shift-up indicator To help enable fuel-efficient driving, the shift-up indicator flashes 3 times to indicate upshift timing. The indicator's default setting is off. The indicator can be turned on/off. (P.
2-1. Driving procedures NOTICE To prevent damage to the transmission Do not shift the shift lever without depressing the clutch pedal. Do not lift up the ring section except when shifting the lever to R. Shift the shift lever to R only when the vehicle is stationary and the clutch pedal is fully depressed.
2-1. Driving procedures Turn signal lever The turn signal lever can be used to show the following intentions of the driver: Right turn Left turn Lane change to the right (push and hold the lever partway) 2 When driving The right hand signals will flash until you release the lever. Lane change to the left (push and hold the lever partway) The left hand signals will flash until you release the lever.
2-1. Driving procedures Parking brake To set the parking brake, fully pull the parking brake lever while depressing the brake pedal. To release the parking brake, slightly raise the lever and lower it completely while pressing the button. Usage in winter time P. 229 NOTICE Before driving Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.
2-1. Driving procedures Horn To sound the horn, press on or close to the mark. 2 When driving After adjusting the steering wheel Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (P.
2-2. Instrument cluster Gauges and meters The illustration below is for left-hand drive vehicles. The switch positions may differ slightly for right-hand drive vehicles. Analog Speedometer Displays the vehicle speed. Tachometer Displays the engine speed in revolutions per minute. Digital Speedometer (if equipped) Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Engine coolant temperature gauge Displays the engine coolant temperature.
2-2. Instrument cluster Odometer, trip meter and multi-information display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently. Multi-information display: Presents the driver with a variety of drivingrelated data. (P. 200) “DISP” switch 2 P. 201 When driving “ODO/TRIP” switch P.
2-2. Instrument cluster Switch the display Each time the “ODO/TRIP” switch is pressed, the display changes as follows. Odometer Trip meter A*1 Trip meter B*1 Setting screen for the shift position indicator and shift-up indicator*2 (vehicles with a manual transmission) *1 : Pressing and holding the “ODO/TRIP” switch will reset the trip meter that is currently displayed.
2-2. Instrument cluster Setting the shift position indicator and shift-up indicator (vehicles with a manual transmission) Displaying of the shift position indicator and shift-up indicator can be turned on/off. STEP 1 Press the “ODO/TRIP” switch repeatedly until the setting screen is displayed. (P. 192) STEP 2 Each time the switch is pressed and held, the display changes between on/off.
2-2. Instrument cluster NOTICE To prevent damage to the engine and its components Do not let the indicator needle of the tachometer enter the red zone, which indicates the maximum engine speed. The engine may be overheating if the temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (P.
2-2. Instrument cluster Indicators and warning lights The indicator and warning lights on the instrument cluster and center panel inform the driver of the status of the vehicle’s various systems. For the purpose of explanation, the following illustration displays all indicators and warning lights illuminated.
2-2. Instrument cluster Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Shift position Indicator (P. 184) Turn signal indicator (P. 187) (Vehicles with a manual transmission) Headlight high beam indicator (P. 206) (If equipped) (If equipped) Shift-up indicator (P. 185) (Vehicles with a manual transmission) Front fog light indicator (P. 212) *1, 2 Rear fog light indicator (P. 212) *1 “TRC OFF” indicator (P.
2-2. Instrument cluster Airbag manual on-off indicator (P. 148) *1: Vehicles without a smart entry & start system These lights turn on when the engine switch is turned to the “ON” position to indicate that a system check is being performed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off.
2-2. Instrument cluster Warning lights Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (P. 362) *1 *1 *1 *2 *3 *1 (If equipped) (If equipped) *1 (for driver) *1 *1 *1 *1 *1 *1 (for front passenger) (If equipped) (If equipped) *1: Vehicles without a smart entry & start system These lights turn on when the engine switch is turned to the “ON” position to indicate that a system check is being performed.
2-2. Instrument cluster CAUTION If a safety system warning light does not come on Should a safety system light such as the ABS and SRS warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional immediately if this occurs.
2-2. Instrument cluster Multi-information display The multi-information display presents the driver with a variety of driving-related data, including the current outside air temperature.
2-2. Instrument cluster Switch the display Each time the “DISP” switch is pressed, the display changes as follows. 2 When driving Outside temperature P. 265 Current fuel consumption Displays the current rate of fuel consumption. Average fuel consumption Displays the average fuel consumption since the function was reset. • The function can be reset by pushing the “DISP” switch for longer than one second when the average fuel consumption is displayed.
2-2. Instrument cluster Setting the REV indicator (if equipped) Changing the REV indicator settings The engine speed at which the REV indicator turns on at and whether a buzzer sounds or not when the light turns on can be set. Engine speed setting range: From 2000 to 7400 rpm (r/min) STEP 1 Press the “DISP” switch repeatedly until the setting screen is displayed. (P. 201) Press and switch. STEP 2 hold the “DISP” “REV.” and the thousandth place flash.
2-2. Instrument cluster Press and switch. STEP 5 hold the “DISP” Each time the “DISP” switch is pressed and held, the buzzer changes between activated and deactivated. “b-on”: Buzzer activated “b-oFF”: Buzzer deactivated When the setting changes from “b-oFF” to “b-on”, the buzzer sounds 3 times. Press the “DISP” switch. When driving STEP 6 2 When the buzzer sounds, all settings have been completed. The settings are displayed.
2-2. Instrument cluster The multi-information display operate when Vehicles without a smart entry & start system The engine switch is in the “ON” position. Vehicles with a smart entry & start system The “ENGINE START STOP” switch is in IGNITION ON mode. CAUTION The information display at low temperatures Allow the interior of the vehicle to warm up before using the liquid crystal information display.
2-3. Operating the lights and windshield wipers Headlight switch The headlights can be operated manually or automatically. Turning the end of the lever turns on the lights as follows: Off The daytime running lights turn on. (if equipped) The headlights, front position, daytime running lights and so on turn on and off automatically.
2-3. Operating the lights and windshield wipers Turning on the high beam headlights With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you and release it to flash the high beams once. You can flash the high beams with the headlights on or off.
2-3. Operating the lights and windshield wipers Manual headlight leveling dial (if equipped) The level of the headlights can be adjusted according to the number of passengers and the loading condition of the vehicle.
2-3. Operating the lights and windshield wipers Daytime running light system Vehicles with halogen headlights Vehicles with an automatic transmission: To make your vehicle more visible to other drivers, the daytime running lights turn on automatically whenever the engine is started, the shift lever is shifted out of P and the parking brake is released. Daytime running lights are not designed for use at night.
2-3. Operating the lights and windshield wipers Automatic light off system (if equipped) Vehicles without a smart entry & start system : The headlights turn off autoWhen the light switch is in or matically if the key is removed from the engine switch. To turn the lights on again, turn the engine switch to the “ON” position, or turn the light switch off once and then back to or .
2-3. Operating the lights and windshield wipers Battery-saving function (if equipped) In the following conditions, the headlights and the other remaining lights will go off automatically after 20 minutes in order to prevent the vehicle battery from being discharged: The headlights and/or tail lights are on. The key is removed from the engine switch (vehicles without a smart entry & start system) or the “ENGINE START STOP” switch is turned off (vehicles with a smart entry & start system).
2-3. Operating the lights and windshield wipers Turning on the low beam headlights when the vehicle is parked in dark areas Turn off the engine with the light switch in or off, and pull the light switch toward you and release it. The low beam headlights will turn on for about 30 seconds to light up the area around the vehicle. The lights are turned off in the following situations. 2 When driving Vehicles without a smart entry & start system: The engine switch is turned to the “ON” position.
2-3. Operating the lights and windshield wipers Fog light switch The fog lights secure excellent visibility in difficult driving conditions, such as in rain and fog. Rear fog light switch Turns the rear fog lights on. Releasing returns it to the switch ring . Operating the switch ring again turns the rear fog lights off.
2-3. Operating the lights and windshield wipers Front and rear fog light switch Turns the front and rear fog lights off Turns the front fog lights on Turns both front and rear fog lights on Releasing returns it to the switch ring 2 . When driving Operating the switch ring again turns only the rear fog lights off. Fog lights can be used when Rear fog light switch The headlights or front position lights are turned on.
2-3. Operating the lights and windshield wipers Windshield wipers and washer When intermittent windshield wiper operation is selected, the wiper interval can be adjusted. The wiper operation is selected by moving the lever as follows.
2-3. Operating the lights and windshield wipers Washer/wiper dual operation The wipers will automatically operate a couple of times after the washer squirts. Vehicles with discharge headlights: When the headlights are on and the lever is pulled and held, the headlight cleaners will operate once. 2 When driving The windshield wipers and washer can be operated when Vehicles without a smart entry & start system The engine switch is in the “ON” position.
2-3. Operating the lights and windshield wipers NOTICE When the windshield is dry Do not use the wipers, as they may damage the windshield. When the washer fluid tank is empty Do not operate the switch continually as the washer fluid pump may overheat. When a nozzle becomes blocked In this case, contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. Do not try to clear it with a pin or other object. The nozzle will be damaged.
2-4. Using other driving systems Cruise control Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicators Cruise control switch 2 When driving Setting the vehicle speed STEP 1 Press the “ON-OFF” button to activate the cruise control. Cruise control indicator (green) will come on. Press the button again to deactivate the cruise control. STEP 2 Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.
2-4. Using other driving systems Adjusting the set speed To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold the lever in the desired direction. The set speed will be increased or decreased as follows: Fine adjustment (vehicles with a km/h odometer display): By approximately 1 km/h (0.6 mph) each time the lever is operated.
2-4. Using other driving systems Canceling and resuming the constant speed control Pulling the lever toward you cancels the constant speed control. The speed setting is also canceled when: • The brakes are applied. • The clutch pedal is depressed (manual transmission only). • The shift lever is shifted to N. 2 When driving Pushing the lever up resumes the constant speed control. Resuming is available when the vehicle speed is more than approximately 32 km/h (20 mph).
2-4. Using other driving systems Accelerating after setting the vehicle speed The vehicle can be accelerated normally. After acceleration, the set speed resumes. Even without canceling the cruise control, the set speed can be increased by first accelerating the vehicle to the desired speed and then pushing the lever down to set the new speed. Automatic cruise control cancelation Cruise control will stop maintaining the vehicle speed in any of the following situations.
2-4. Using other driving systems CAUTION To avoid operating the cruise control by mistake Switch the cruise control off using the “ON-OFF” button when not in use. Situations unsuitable for cruise control Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury.
2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following systems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle.
2-4. Using other driving systems Disabling the TRC system If the vehicle gets stuck in mud, dirt or snow, the TRC system may reduce power from the engine to the wheels. Pressing to turn the system off may make it easier for you to rock the vehicle in order to free it. To turn the TRC system off, quickly press and release the button. 2 When driving The “TRC OFF” indicator light will come on. Press the button again to turn the system back on.
2-4. Using other driving systems Turning off both TRC and VSC systems To turn the TRC and VSC systems off, press and hold seconds while the vehicle is stopped. for more than 3 The “TRC OFF” indicator light and the VSC off indicator light will come on. Press the button again to turn the systems back on.
2-4. Using other driving systems Reduced effectiveness of the EPS system The effectiveness of the EPS system is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the engine off. The EPS system should return to normal after a little while.
2-4. Using other driving systems CAUTION When the VSC is activated The slip indicator light flashes. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes. When the TRC/VSC systems are turned off Be especially careful and drive at a speed appropriate to the road conditions. As these are the systems to ensure vehicle stability and driving force, do not turn the TRC/VSC systems off unless necessary.
2-5. Driving information Cargo and luggage Take notice of the following information about storage precautions, cargo capacity and load: Stow cargo and luggage in the trunk whenever possible. Be sure all items are secured in place. To maintain vehicle balance while driving, position luggage evenly within the luggage compartment. For better fuel economy, do not carry unnecessary weight.
2-5. Driving information CAUTION Storage precautions Observe the following precautions. Failure to do so may result in death or serious injury. Stow cargo and luggage in the trunk whenever possible. To prevent cargo and luggage from sliding forward during braking, do not stack anything in the enlarged trunk. Keep cargo and luggage low, as close to the floor as possible. When you fold down the rear seats, long items should not be placed directly behind the front seats.
2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropriate to the prevailing weather conditions. Pre-winter preparations Use fluids that are appropriate to the prevailing outside temperatures. • Engine oil • Washer fluid 2 Have a service technician inspect the condition of the battery.
2-5. Driving information If a door is opened and closed when its side window is frozen, the window safety device will operate and the side window open/close function linked to door operation may not operate correctly. If this occurs, perform the following after the ice has melted. STEP 1 Open the side window until it is approximately halfway open.
2-5. Driving information Regulations on the use of tire chains Regulations regarding the use of tire chains vary according to location and type of road. Always check local regulations before installing chains. Tire chains Observe the following precautions when installing and removing chains. 2 Install and remove tire chains in a safe location. Install tire chains on the rear tires. Do not install tire chains on front tires. When driving Install tire chains on rear tires as tightly as possible.
2-5. Driving information CAUTION Driving with tire chains Vehicles with an emergency tire puncture repair kit: When any of the tires are punctured, you can seal the tire temporarily. However, do not use the tire chain on a sealed tire. If any of the rear tires are punctured although it is required to use tire chains, contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. Observe the following precautions to reduce the risk of accidents.
2-5. Driving information Trailer towing Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your Toyota is not designed for trailer towing or for the use of tow hitch mounted carriers.
2-5.
Interior features 3-1. Using the air conditioning system and defogger Manual air conditioning system ............................ 236 Automatic air conditioning system ............................ 244 Rear window and outside rear view mirror defoggers ............. 252 3-2. Using the audio system Using the AUX/USB port ................................. 254 3 3-5. Other interior features Sun visors ......................... Vanity mirrors.................... Clock.................................
3-1. Using the air conditioning system and defogger Manual air conditioning system Temperature control dial Air outlet selection dial Outside air or recirculated air mode Fan speed control dial Air conditioning on/off button (if equipped) Adjusting the settings STEP 1 To adjust the fan speed, turn the fan speed control dial clockwise (increase) or counterclockwise (decrease). Turning the dial to “0” turns off the fan.
3-1. Using the air conditioning system and defogger STEP 2 Vehicles with the button: To adjust the temperature setting, turn the temperature control dial clockwise (warm) or counterclockwise (cool). is not pressed, the system will blow ambient temperature air or heated air. STEP 3 To select the air outlets, set the air outlet selection dial to the desired position. The positions between the air outlet selections shown below can also be selected for more delicate adjustment.
3-1. Using the air conditioning system and defogger Defogging the windshield Set the air outlet selection dial to position. STEP 1 If the recirculated air mode is used, it will automatically switch to the outside air mode. STEP 2 Perform the following operations accordingly: To adjust the fan speed, turn the fan speed control dial. To adjust the temperature setting, turn the temperature control dial.
3-1. Using the air conditioning system and defogger Air outlets and air flow Air flows to the upper body. Air flows to the upper body and feet. 3 Interior features Air flows to the feet. Air flows to the feet and the windshield defogger operates.
3-1. Using the air conditioning system and defogger Switching between outside air and recirculated air modes Press . The mode switches between outside air mode (introduces air from outside the vehicle) (indicator off) and recirculated air mode (recycles air inside the vehicle) (indicator on) each time the button is pressed. Adjusting the position of the air outlets Center outlets Direct air flow to the left or right, up or down.
3-1. Using the air conditioning system and defogger Opening and closing the air outlets Center outlets Open the air outlet. Close the air outlet. Right and left side outlets 3 Open the vent. Interior features Close the vent.
3-1. Using the air conditioning system and defogger Fogging up of the windows Vehicles with the button: The windows will easily fog up when the humidity in the vehicle is high. Turning on will dehumidify the air from the outlets and defog the windshield effectively. Vehicles with the button: If you turn off, the windows may fog up more easily. The windows may fog up if the recirculated air mode is used.
3-1. Using the air conditioning system and defogger Air conditioning odors During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents. To reduce potential odors from occurring: It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off. Air conditioning filter P.
3-1. Using the air conditioning system and defogger Automatic air conditioning system Air outlets are automatically selected and fan speed is automatically adjusted according to the set temperature setting. The illustration below is for left-hand drive vehicles. The button positions may differ slightly for right-hand drive vehicles.
3-1. Using the air conditioning system and defogger Using the automatic air conditioning system STEP 1 Press . The dehumidification function begins to operate. Air outlets and fan speed are automatically adjusted according to the temperature setting. STEP 2 Turn temperature control dial clockwise to increases the temperature and turn temperature control dial counterclockwise to decreases the temperature on the driver’s side.
3-1. Using the air conditioning system and defogger STEP 3 To change the air outlets, press . The air outlets used are switched each time either side of the button is pressed. Defogging the windshield Press . The dehumidification function operates and fan speed increases. Set the outside/recirculated air mode button to outside air mode if the recirculated air mode is used. (It may switch automatically.) To defog the windshield and the side windows early, turn the air flow and temperature up.
3-1. Using the air conditioning system and defogger Air outlets and air flow Air flows to the upper body. Air flows to the upper body and feet. 3 Interior features Air flows to the feet. Air flows to the feet and the windshield defogger operates. If the recirculated air mode is used, it may automatically switch to the outside air mode.
3-1. Using the air conditioning system and defogger Switching between outside air mode and recirculated air mode Press . The mode switches between outside air mode (indicator off) and recirculated air mode (indicator on) each time is pressed. Adjusting the position of the air outlets Center outlets Direct air flow to the left or right, up or down. Right and left side outlets Direct air flow to the left or right, up or down.
3-1. Using the air conditioning system and defogger Opening and closing the air outlets Center outlets Open the air outlet. Close the air outlet. Right and left side outlets 3 Open the vent. Interior features Close the vent.
3-1. Using the air conditioning system and defogger Using automatic mode Fan speed is adjusted automatically according to the temperature setting and the ambient conditions. Therefore, the fan may stop for a while until warm or cool air is ready to flow immediately after is pressed. Fogging up of the windows The windows will easily fog up when the humidity in the vehicle is high. Turning on will dehumidify the air from the outlets and defog the windshield effectively.
3-1. Using the air conditioning system and defogger Air conditioning odors During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents. To reduce potential odors from occurring: • It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.
3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers The rear window defogger is used to defog the rear window. The outside rear view mirror defoggers* are used to remove frost, dew or raindrops from the outside rear view mirrors. Vehicles with a manual air conditioning system On/off The defoggers will automatically turn off after approximately 15 minutes.
3-1. Using the air conditioning system and defogger The defoggers can be operated when Vehicles without a smart entry & start system The engine switch is in the “ON” position. Vehicles with a smart entry & start system The “ENGINE START STOP” switch is in IGNITION ON mode. The outside rear view mirror defoggers (vehicles with outside rear view mirror defoggers) Turning the rear window defogger on will turn the outside rear view mirror defoggers on.
3-2. Using the audio system Using the AUX/USB port This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers. Depending on the type of portable audio device, some device operation may not be available. Open the cover and connect the portable audio device. Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle's audio controls. All other adjustments must be made on the portable audio device itself.
3-3. Using the interior lights Interior lights list 3 Interior features Interior light (P.
3-3. Using the interior lights Interior light Interior light Turns the light off Turns the door position on Turns the light on Illuminated entry system Vehicles without a smart entry & start system The lights automatically turn on/off according to the engine switch position, whether the doors are locked/unlocked, and whether the doors are open/ closed.
3-4. Using the storage features List of storage features 3 Interior features Glove box Bottle holders Cup holders (if equipped)/console tray CAUTION Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: Glasses may be deformed by heat or cracked if they come into contact with other stored items. Lighters or spray cans may explode.
3-4. Using the storage features Glove box Glove box Pull up the lever to open the glove box. CAUTION Caution while driving Keep the glove box closed. In the event of sudden braking or sudden swerving, an accident may occur due to an occupant being struck by the open glove box or the items stored inside.
3-4. Using the storage features Bottle holders Bottle holders When using the bottle holder 3 When storing a bottle, close the cap. The bottle may not be stored depending on its size or shape. Interior features CAUTION Items unsuitable for the bottle holder Do not place anything other than a pet bottle in the bottle holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.
3-4. Using the storage features Cup holders/console tray Cup holders (if equipped)/console tray Changing the cup holder position Remove the cup holder and change the holder position. Changing the console tray size Remove the cup holder.
3-4. Using the storage features Cup holders/console tray CAUTION Caution while driving Observe the following precautions. Failure to do so may cause an accident resulting in death or serious injury. Before driving, place the cup holder in the rear position so that it does not hinder shift lever operation. When placing the cup holder, make sure it is facing the correct direction. Failure to do so will cause the cup holder to not be secure in the console tray and hinder shift lever operation.
3-5. Other interior features Sun visors To set the visor in the forward position, flip it down. To set the visor in the side position, flip down, unhook, and swing it to the side.
3-5. Other interior features Vanity mirrors Open the cover to use. Vehicles with vanity lights: The light turns on when the cover is opened. NOTICE To prevent battery discharge (vehicles with vanity lights) 3 Do not leave the vanity lights on for extended periods while the engine is off.
3-5. Other interior features Clock The clock can be adjusted by pressing the buttons. Adjusts the hours Adjusts the minutes Rounds hour* to the nearest *: e.g.1:00 to 1:29 1:00 00 1:30 to 1:59 2:00 The clock is displayed when Vehicles without a smart entry & start system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart entry & start system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.
3-5. Other interior features Outside temperature display The temperature display shows temperatures within the range of -40°C (-40°F) and 50°C (122°F). The outside temperature display can be switched by pressing the “DISP” switch. (P. 201) 3 The outside temperature is displayed when Interior features Vehicles without a smart entry & start system The engine switch is in the “ON” position. Vehicles with a smart entry & start system The “ENGINE START STOP” switch is in IGNITION ON mode.
3-5. Other interior features Ashtray The ashtray can be installed in the cup holder. (P. 260) CAUTION When not in use Keep the ashtray closed. In the event of sudden braking, an accident may occur due to an occupant being struck by the open ashtray or ash flying out. To prevent fire Fully extinguish matches and cigarettes before putting them in the ashtray, then make sure the ashtray is fully closed. Do not place paper or any other type of flammable object in the ashtray.
3-5. Other interior features Power outlets The power outlet can be used for 12 V accessories that run on 10 A or less.
3-5. Other interior features The power outlet can be used when Vehicles without a smart entry & start system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart entry & start system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode. NOTICE To avoid damaging the power outlet Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short circuit.
3-5. Other interior features Seat heaters Press the switch to warm the seats. The indicator light comes on when a seat heater is turned on. Rapid heating Normal heating The seat heaters can be used when 3 The “ENGINE START STOP” switch is in IGNITION ON mode. When not in use Interior features Turn the seat heater off. The indicator light goes off.
3-5. Other interior features NOTICE To prevent seat heater damage Do not put heavy objects that have an uneven surface on the seat and do not stick sharp objects (needles, nails, etc.) into the seat. To prevent battery discharge Turn the seat heaters off when the engine is not running.
3-5. Other interior features Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Front Driver’s seat floor mat Front passenger’s seat floor mat Retaining hook (clip) eyelets Rear Rear seat floor mats 3 Installing the floor mats (front) Insert the retaining hooks (clips) into the floor mat eyelets. STEP 2 Turn the upper knob of each retaining hook (clip) to secure the floor mats in place.
3-5. Other interior features CAUTION Observe the following precautions. Failure to do so may cause the driver's floor mat to slip, possibly interfering with the pedals while driving. An unexpectedly high speed may result or it may become difficult to stop the vehicle, leading to a serious accident. When installing a floor mat Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats.
3-5. Other interior features NOTICE When installing the rear floor mats Make sure that the rear floor mats are installed in the correct position. If a floor mat is positioned incorrectly, it may interfere with the seat rail or other parts when a front seat is moved forward or backward, damaging the vehicle or floor mat.
3-5. Other interior features Trunk features (vehicles with an emergency tire puncture repair kit) Auxiliary box Vehicles with a luggage mat: Lift up the luggage mat.
3-5. Other interior features Warning reflector storage box The warning reflector can be stored. 3 Interior features Warning reflector storage box Depending on the size and shape of the warning reflector case, it may not be able to be stored. CAUTION When storing a warning reflector Make sure that the warning reflector is stored securely. Failure to do so may cause it jump out of position in the event of sudden braking, etc., causing an accident.
3-5.
Maintenance and care 4 4-1. Maintenance and care Cleaning and protecting the vehicle exterior ......... 278 Cleaning and protecting the vehicle interior .......... 282 Cleaning and protecting the Alcantara® area ........ 286 4-2. Maintenance Maintenance requirements................... 288 4-3. Do-it-yourself maintenance Do-it-yourself service precautions ..................... Hood ................................. Positioning a floor jack...... Engine compartment......... Tires.............................
4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition. Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust. Wash the vehicle body using a sponge or soft cloth, such as a chamois. For hard-to-remove marks, use car wash soap and rinse thoroughly with water. Wipe away any water.
4-1. Maintenance and care Automatic car washes Fold the mirrors and remove the antenna before washing the vehicle. Start washing from the front of the vehicle. Make sure to re-install the antenna and extend the mirrors before driving. Brushes used in automatic car washes may scratch the vehicle surface and harm your vehicle’s paint. Vehicles with a rear spoiler: In certain automatic car washes, the rear spoiler may interfere with machine operation.
4-1. Maintenance and care CAUTION When washing the vehicle Do not apply water to the inside of the engine compartment. Doing so may cause the electrical components etc. to catch fire. Precautions regarding the exhaust pipes Exhaust gasses cause the exhaust pipes and rear bumper diffusers to become quite hot. When washing the vehicle, be careful not to touch the pipes and diffusers until they have cooled sufficiently, as touching hot exhaust pipes and rear bumper diffusers can cause burns.
4-1. Maintenance and care NOTICE Cleaning the exterior lights Wash carefully. Do not use organic substances or scrub with a hard brush. This may damage the surfaces of the lights. Do not apply wax on the surfaces of the lights. Wax may cause damage to the lenses. Antenna installation and removal precautions Before driving, ensure that the antenna is installed.
4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle's interior and keep it in top condition: Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water. When the interior is extremely dirty, wipe away the dirt using a soft cloth slightly dampened with diluted neutral detergent.
4-1. Maintenance and care Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior. Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. Excellent results are obtained by keeping the carpet as dry as possible. Seat belts Clean with mild soap and lukewarm water using a cloth or sponge.
4-1. Maintenance and care NOTICE Cleaning detergents Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. Do not use polish wax or polish cleaner. The instrument panel's or other interior part’s painted surface may be damaged.
4-1. Maintenance and care NOTICE Cleaning the inside of the rear window Be careful not to scratch or damage the heater wires. Do not use glass cleaner to clean the rear window, as this may cause damage to the rear window defogger heater wires. Use a cloth dampened with lukewarm water to gently wipe the window clean. Wipe the window in strokes running parallel to the heater wires.
4-1. Maintenance and care Cleaning and protecting the Alcantara® area The following procedures will protect and keep your vehicle’s Alcantara® upholstery in top condition: Day-to-day cleaning Perform the following procedures regularly (approximately once a month). STEP 1 Wipe the entire Alcantara® area with a soft cloth that has been dampened with lukewarm water (approximately 40C [104F]) and squeezed out. Do not wipe too hard. Doing so may make the Alcantara® upholstery surface become uneven.
4-1. Maintenance and care STEP 2 If the Alcantara® upholstery surface becomes uneven, lightly brush it with a soft brush. STEP 3 Allow the surface to dry completely. Oil stains You will need the following items: A cloth that has been dampened with benzene A dry cloth STEP 1 Using a dry cloth or tissue paper, wipe away as much of the oil as possible to prevent the stained area from expanding.
4-2. Maintenance Maintenance requirements To ensure safe and economical driving, day-to-day care and regular maintenance is essential. Toyota recommends the following maintenance. Scheduled maintenance Scheduled maintenance be performed at specified intervals according to the maintenance schedule. For full details of your maintenance schedule, read the “Toyota Service Booklet” or “Toyota Warranty Booklet”.
4-2. Maintenance Where to go for service? In order to maintain your vehicle in the highest possible condition, Toyota recommends that all repairs and service operations be carried out by authorized Toyota dealers or repairers or other duly qualified and equipped professionals. For repairs and services covered by your warranty, please visit an authorized Toyota dealer or repairer, who will use genuine Toyota parts in repairing any difficulties you may encounter.
4-2. Maintenance CAUTION If your vehicle is not properly maintained It could result in serious damage to the vehicle and possible serious injury or death. Warning in handling of the battery Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (P.
4-3. Do-it-yourself maintenance Do-it-yourself service precautions If you perform maintenance yourself, be sure to follow the correct procedures as given in these sections. Items Parts and tools (P. 302) • “TOYOTA Genuine 50/50 Premixed Super Long Life Coolant BLUE” or similar high-quality ethylene glycol-based nonsilicate, non-amine, non-nitrite and non-borate coolant with longlife hybrid organic acid technology.
4-3. Do-it-yourself maintenance Items Parts and tools Radiator and condenser (P. 304) Tire inflation pressure (P. 314) • Tire pressure gauge • Compressed air source Washer fluid • Water washer fluid containing antifreeze (for winter use) • Funnel (P. 309) CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions.
4-3. Do-it-yourself maintenance CAUTION When working near the electric cooling fans or radiator grille Vehicles without a smart entry & start system: Be sure the engine switch is off. With the engine switch in the “ON” position, the electric cooling fans may automatically start to run if the air conditioning is on and/or the coolant temperature is high. (P. 304) Vehicles with a smart entry & start system: Be sure the “ENGINE START STOP” switch is off.
4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. STEP 1 Pull the hood release lever. The hood will pop up slightly. 294 FT86_EE STEP 2 Push the auxiliary catch lever to the left and lift the hood. STEP 3 Hold the hood open by inserting the supporting rod into the slot.
4-3. Do-it-yourself maintenance CAUTION Pre-driving check Check that the hood is fully closed and locked. If the hood is not locked properly it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury. NOTICE When opening the hood Do not lift up or operate the wipers. Doing so may cause the hood and wipers to contact, scratching the hood.
4-3. Do-it-yourself maintenance Positioning a floor jack When raising your vehicle with a floor jack, position the jack correctly. Improper placement may damage your vehicle or cause injury.
4-3. Do-it-yourself maintenance CAUTION When raising your vehicle Make sure to observe the following precautions to reduce the possibility of death or serious injury: Lift up the vehicle using a floor jack such as the one shown in the illustration. When using a floor jack, follow the instructions of the manual provided with the jack. Do not use the jack that was supplied with your vehicle. Do not put any part of your body underneath the vehicle when it is supported only by the floor jack.
4-3. Do-it-yourself maintenance Engine compartment Battery* (P. 305) Electric cooling fans Engine oil level dipstick (P. 299) Condenser (if equipped) (P. 304) Engine oil filler cap (P. 300) Radiator Washer fluid tank (P. 309) (P. 304) Engine coolant reservoir (P. 302) Fuse box (P. 324) *: For right-hand drive vehicles: This is located on the opposite side of the engine compartment.
4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. Checking the engine oil STEP 1 Park the vehicle on level ground. After warming up the engine and turning it off, wait more than five minutes for the oil to drain back into the bottom of the engine. STEP 2 Hold a rag under the end and pull the dipstick out. 4 Wipe the dipstick clean. STEP 4 Reinsert the dipstick fully.
4-3. Do-it-yourself maintenance Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine. Make sure to check the oil type and prepare the items needed before adding oil. Engine oil selection Oil quantity (Low Full) Items 300 FT86_EE P. 420 1.0 L (1.1 qt., 0.9 Imp. qt.) Clean funnel STEP 1 Remove the oil filler cap by turning it counterclockwise. STEP 2 Add engine oil slowly, checking the dipstick.
4-3. Do-it-yourself maintenance Engine oil consumption The amount of engine oil consumed depends on the oil viscosity, the quality of the oil and the way the vehicle is driven. More oil is consumed under driving conditions such as high speeds and frequent acceleration and deceleration. A new engine consumes more oil. When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately. Oil consumption: Max. 1.
4-3. Do-it-yourself maintenance NOTICE To prevent serious engine damage Check the oil level on a regular basis. When replacing the engine oil Be careful not to spill engine oil on the vehicle components. Avoid overfilling, or the engine could be damaged. Check the oil level on the dipstick every time you refill the vehicle. Be sure the engine oil filler cap is properly tightened.
4-3. Do-it-yourself maintenance Coolant selection Only use “TOYOTA Genuine 50/50 Pre-mixed Super Long Life Coolant BLUE” or similar high-quality ethylene glycol-based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology. “TOYOTA Genuine 50/50 Pre-mixed Super Long Life Coolant BLUE” is a mixture of 50% coolant and 50% deionized water.
4-3. Do-it-yourself maintenance Radiator and condenser Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. CAUTION When the engine is hot Do not touch the radiator or condenser as they may be hot and cause serious injuries, such as burns.
4-3. Do-it-yourself maintenance Battery Check the battery as follows. Caution symbols The meanings of each caution symbol on the top of the battery are as follows: No smoking, no naked flames, no sparks Battery acid Shield eyes Note operating instructions Keep away from children Explosive gas Battery exterior Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.
4-3. Do-it-yourself maintenance Checking battery fluid Check that the level is between “UPPER LEVEL” and “LOWER LEVEL”. “UPPER LEVEL” “LOWER LEVEL” If the fluid level is at or below “LOWER LEVEL”, add distilled water. Adding distilled water Low O.K. STEP 1 Remove the vent plug. STEP 2 Add distilled water. If the “UPPER LEVEL” line cannot be seen, check the fluid level by looking directly at the cell. STEP 3 306 FT86_EE Put the vent plug back on and close securely.
4-3. Do-it-yourself maintenance Before recharging When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging: If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable. Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.
4-3. Do-it-yourself maintenance CAUTION Chemicals in the battery A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery: Do not cause sparks by touching the battery terminals with tools. Do not smoke or light a match near the battery. Avoid contact with eyes, skin and clothes. Never inhale or swallow electrolyte.
4-3. Do-it-yourself maintenance NOTICE When recharging the battery Never recharge the battery while the engine is running. Also, be sure all accessories are turned off. When adding distilled water Avoid overfilling. Water spilled during battery recharging may cause corrosion. Washer fluid If the washer fluid level is at “LOW”, add washer fluid.
4-3. Do-it-yourself maintenance CAUTION When adding washer fluid Do not add washer fluid when the engine is hot or running, as washer fluid contains alcohol and may catch fire if spilled on the engine etc. NOTICE Washer fluid Do not use soapy water or engine antifreeze instead of washer fluid. Doing so may cause streaking on the vehicle’s painted surfaces. Diluting washer fluid Dilute washer fluid with water as necessary.
4-3. Do-it-yourself maintenance Tires Replace or rotate tires in accordance with maintenance schedules and treadwear. Checking tires New tread Treadwear indicator Worn tread The location of treadwear indicators is shown by the “TWI” or “ ” marks, etc., molded on the sidewall of each tire. Check spare tire condition and pressure if not rotated. Tire rotation Vehicles with an emergency tire puncture repair kit Rotate the tires in the order shown.
4-3. Do-it-yourself maintenance Vehicles with a spare tire of the same wheel type as the installed tires Rotate the tires in the order shown. Front To equalize tire wear and help extend tire life, Toyota recommends that tire rotation is carried out approximately every 10000 km (6000 miles).
4-3. Do-it-yourself maintenance CAUTION When inspecting or replacing tires Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the drive train, as well as dangerous handling characteristics, which may lead to an accident resulting in death or serious injury. Make sure to install 4 tires that are of the specified size, and that all 4 tires are the same size, same maker, same brand and tread pattern.
4-3. Do-it-yourself maintenance Tire inflation pressure Make sure to maintain the proper tire inflation pressure. Tire inflation pressure should be checked at least once per month. However, Toyota recommends that tire inflation pressure be checked once every two weeks. (P.
4-3. Do-it-yourself maintenance CAUTION Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury.
4-3. Do-it-yourself maintenance Wheels If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. Wheel selection When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and inset*. Replacement wheels are available at any authorized Toyota dealer or repairer, or another duly qualified and equipped professional.
4-3. Do-it-yourself maintenance CAUTION When replacing wheels Do not use wheels that are a different size from those recommended in the Owner’s Manual, as this may result in loss of handling control. Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing death or serious injury. When installing the wheel nuts Tapered portion Be sure to install the wheel nuts with the tapered ends facing inward.
4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. Removal method STEP 1 Vehicles without a smart entry & start system Turn the engine switch off. Vehicles with a smart entry & start system Turn the “ENGINE START STOP” switch off. 318 FT86_EE STEP 2 Open the glove box. Slide off the damper. STEP 3 Push in each side of the glove box to disconnect the claws.
4-3. Do-it-yourself maintenance STEP 5 Remove the filter cover. STEP 6 Remove the air conditioning filter and replace it with a new one. The “UP” marks shown on the filter should be pointing up. 4 Maintenance and care Checking interval Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required.
4-3. Do-it-yourself maintenance Wireless remote control/electronic key battery Replace the battery with a new one if it is depleted. You will need the following items: Flathead screwdriver Lithium battery CR2016 (vehicles without a smart entry & start system), or CR1632 (vehicles with a smart entry & start system) Replacing the battery (vehicles without a smart entry & start system) STEP 1 Remove the cover. To prevent damage to the key, cover the tip of the screwdriver with a rag.
4-3. Do-it-yourself maintenance STEP 3 Open the case cover using a coin protected with tape etc. and remove the depleted battery. Insert a new battery with the “+” terminal facing up. Replacing the battery (vehicles with a smart entry & start system) STEP 1 Take out the mechanical key. 4 Maintenance and care STEP 2 Remove the cover. To prevent damage to the key, cover the tip of the screwdriver with a rag.
4-3. Do-it-yourself maintenance Remove the depleted battery. STEP 3 Insert a new battery with the “+” terminal facing up. Use a CR2016 (vehicles without a smart entry & start system) or CR1632 (vehicles with a smart entry & start system) lithium battery Batteries can be purchased at any authorized Toyota dealer or repairer, or another duly qualified and equipped professional, local electrical appliance shops or camera stores.
4-3. Do-it-yourself maintenance CAUTION Removed battery and other parts Keep away from children. These parts are small and if swallowed by a child, they can cause choking. Failure to do so could result in death or serious injury. Certification for the lithium battery RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. STEP 1 Vehicles without a smart entry & start system Turn the engine switch off. Vehicles with a smart entry & start system Turn the “ENGINE START STOP” switch off. STEP 2 Open the fuse box cover. Engine compartment Push the tabs in and lift the lid off. Instrument panel Remove the lid.
4-3. Do-it-yourself maintenance STEP 3 After a system failure, see “Fuse layout and amperage ratings” (P. 327) for details about which fuse to check. STEP 4 Remove the fuse with the pullout tool. STEP 5 Check if the fuse has blown. Type A Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid. 4 Maintenance and care Type B Normal fuse Blown fuse Replace it with one of an appropriate amperage rating.
4-3. Do-it-yourself maintenance Type C Normal fuse Blown fuse Contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. Type D Normal fuse Blown fuse Contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional.
4-3. Do-it-yourself maintenance Fuse layout and amperage ratings Engine compartment Fuse Ampere Circuit MIR HTR 7.5 A Outside rear view mirror defoggers 2 RDI 25 A Electric cooling fan 3 (PUSH-AT) 7.5 A Engine control unit 4 ABS NO.
4-3. Do-it-yourself maintenance Fuse 328 FT86_EE Ampere Circuit 16 SPARE See note. Spare fuse 17 SPARE See note. Spare fuse 18 SPARE See note. Spare fuse 19 SPARE See note. Spare fuse 20 SPARE See note. Spare fuse 21 ST 7.5 A Starting system 22 ALT-S 7.5 A Charging system 23 (STR LOCK) 7.5 A Steering lock system 24 D/L 20 A Power door lock 25 ETCS 15 A Engine control unit 26 (AT+B) 7.5 A Transmission 27 (AM2 NO. 2) 7.
4-3. Do-it-yourself maintenance Fuse Ampere Circuit HORN NO. 2 7.5 A Horn 38 HORN NO. 1 7.5 A Horn 39 H-LP LH LO 15 A Left-hand headlight (low beam) 40 H-LP RH LO 15 A Right-hand headlight (low beam) 41 H-LP LH HI 10 A Left-hand headlight (high beam) 42 H-LP RH HI 10 A Right-hand headlight (high beam) 43 INJ 30 A Multiport fuel injection system/ sequential multiport fuel injection system 44 H-LP WASHER 30 A Headlight cleaners 45 AM2 NO.
4-3. Do-it-yourself maintenance Instrument panel Fuse 330 FT86_EE Ampere 1 ECU ACC 10 A 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 P/POINT No.2 PANEL TAIL DRL STOP OBD HEATER-S HEATER FR FOG LH FR FOG RH BK/UP LP ECU IG1 AM1 AMP AT UNIT 15 A 10 A 10 A 10 A 7.5 A 7.5 A 7.5 A 10 A 10 A 10 A 7.5 A 10 A 7.5 A 15 A 15 A 17 GAUGE 7.5 A 18 19 20 21 22 ECU IG2 SEAT HTR LH SEAT HTR RH RADIO P/POINT No.1 10 A 10 A 10 A 7.
4-3. Do-it-yourself maintenance After a fuse is replaced If the lights do not turn on even after the fuse has been replaced, a bulb may need replacement. (P. 332) If the replaced fuse blows again, have the vehicle inspected by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. If there is an overload in the circuits The fuses are designed to blow, protecting the wiring harness from damage.
4-3. Do-it-yourself maintenance Light bulbs You may replace the following bulbs by yourself. The difficulty level of replacement varies depending on the bulb. As there is a danger that components may be damaged, we recommend that replacement is carried out by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. Preparing a replacement light bulb Check the wattage of the light bulb being replaced. (P.
4-3.
4-3. Do-it-yourself maintenance Replacing light bulbs Headlight low beams (vehicles with halogen bulbs) STEP 1 Turn the bulb base counterclockwise. STEP 2 Unplug the connector while depressing the lock release. STEP 3 Replace the light bulb, and install the bulb base. Align the 3 tabs on the light bulb with the mounting, and insert.
4-3. Do-it-yourself maintenance STEP 4 Turn and secure the bulb base. Shake the bulb base gently to check that it is not loose, turn the headlight low beams on once and visually confirm that no light is leaking through the mounting. Headlight high beams (vehicles with halogen bulbs) STEP 1 Unplug the connector while depressing the lock release. 4 Turn the bulb base counterclockwise. STEP 3 Install a new bulb.
4-3. Do-it-yourself maintenance STEP 4 Turn and secure the bulb. Install the connector. Shake the bulb base gently to check that it is not loose, turn the headlight high beams on once and visually confirm that no light is leaking through the mounting. Front position lights (vehicles with halogen headlights) STEP 1 Turn the bulb base counterclockwise. STEP 2 Remove the light bulb. STEP 3 336 FT86_EE When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance Side turn signal lights STEP 1 Turn the steering wheel in the opposite direction of the light to be replaced. Turn the steering wheel to a point that allows your hand to easily fit between the tire and fender liner. STEP 2 Remove the clip and partly remove the fender liner. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag. 4 Release the light’s claw. Maintenance and care STEP 3 Insert the screwdriver into the hole.
4-3. Do-it-yourself maintenance Remove the light bulb. STEP 5 STEP 6 When installing, reverse the steps listed. Front turn signal lights STEP 1 Turn the steering wheel in the opposite direction of the light to be replaced. Turn the steering wheel to a point that allows your hand to easily fit between the tire and fender liner. STEP 2 Remove the clips and partly remove the fender liner. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag.
4-3. Do-it-yourself maintenance STEP 3 Turn the bulb base counterclockwise. STEP 4 Remove the light bulb. STEP 5 4 When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance Daytime running lights (vehicles with halogen headlights)/ front fog lights (if equipped) STEP 1 Turn the steering wheel in the opposite direction of the light to be replaced. Turn the steering wheel to a point that allows your hand to easily fit between the tire and fender liner. STEP 2 Remove the clips and partly remove the fender liner. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag.
4-3. Do-it-yourself maintenance Daytime running lights/front fog lights STEP 3 Front fog lights Unplug the connector and remove the light bulb. Daytime running lights Remove the light bulb. Daytime running lights STEP 3 Remove the light bulb. 4 Replace the light bulb with a new one. STEP 5 Daytime running lights/front fog lights Turn and secure the bulb. Install the connector. Maintenance and care 4 STEP 5 Daytime running lights Turn and secure the bulb.
4-3. Do-it-yourself maintenance Front fog lights (vehicles with discharge headlights) STEP 1 Turn the steering wheel in the opposite direction of the light to be replaced. Turn the steering wheel to a point that allows your hand to easily fit between the tire and fender liner. STEP 2 Remove the clips and partly remove the fender liner. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag. STEP 3 342 FT86_EE Unplug the connector while depressing the lock release.
4-3. Do-it-yourself maintenance Remove the light bulb. STEP 4 STEP 5 When installing, reverse the steps listed. Rear turn signal lights STEP 1 On some models, remove a clip and partly remove the cover. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag. 4 Maintenance and care STEP 2 Turn the bulb base counterclockwise.
4-3. Do-it-yourself maintenance Remove the light bulb. STEP 3 STEP 4 When installing, reverse the steps listed. Back-up lights STEP 1 Turn the bulb base counterclockwise. STEP 2 3 Remove the light bulb. STEP 3 344 FT86_EE When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance Rear fog light STEP 1 Turn the bulb base counterclockwise. STEP 2 3 Remove the light bulb. 4 When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance License plate lights STEP 1 Vehicles with a trunk panel cover: Remove the trunk panel cover clips and partly remove the trunk panel cover. To prevent damage to the vehicle, cover the tip of the screwdriver with a rag. STEP 2 Turn the bulb base counterclockwise. STEP 3 Remove the light bulb. STEP 4 346 FT86_EE When installing, reverse the steps listed.
4-3. Do-it-yourself maintenance Replacing the following bulbs If any of the lights listed below has burnt out, have it replaced by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional.
4-3. Do-it-yourself maintenance When replacing light bulbs Toyota recommends that you use genuine Toyota products designed for this vehicle. Because certain bulbs are connected to circuits designed to prevent overload, non-genuine parts or parts not designed for this vehicle may be unusable. Removing and installing the luggage trim cover and trunk panel cover clip Removing Installing CAUTION Replacing light bulbs Turn off the lights.
4-3. Do-it-yourself maintenance CAUTION Discharge headlights (if equipped) Contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional, before replacing the discharge headlights (including light bulbs). Do not touch the discharge headlight’s high voltage socket when the headlights are turned on. An extremely high voltage of 25000 V will be discharged and could result in serious injury or death by electric shock.
4-3.
When trouble arises 5-1. Essential information Emergency flashers.......... If your vehicle needs to be towed ......................... If you think something is wrong.............................. Fuel pump shut off system ............................ 352 353 360 361 5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds... ........................ If you have a flat tire (vehicles with a spare tire) .................................
5-1. Essential information Emergency flashers The emergency flashers are used to warn other drivers when the vehicle has to be stopped in the road due to a breakdown, etc. Press the switch. All the turn signal lights will flash. To turn them off, press the switch once again. Emergency flashers If the emergency flashers are used for a long time while the engine is not operating, the battery may discharge.
5-1. Essential information If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/provincial and local laws. If towing from the rear, the vehicle's front wheels and axles must be in good condition. (P.
5-1. Essential information Towing eyelet Before emergency towing STEP 1 Release the parking brake. STEP 2 Shift the shift lever to N. STEP 3 Vehicles without a smart entry & start system: Turn the engine switch to the “ACC” (engine off) or “ON” (engine running) position. Vehicles with a smart entry & start system: Turn the “ENGINE START STOP” switch to ACCESSORY (engine off) or IGNITION ON (engine running) mode. If towing a vehicle Do not tow another vehicle.
5-1. Essential information NOTICE To prevent causing serious damage to the transmission in emergency towing (vehicles with an automatic transmission) Never tow a vehicle from the rear with four wheels on the ground. This may cause serious damage to the transmission. Installing towing eyelet STEP 1 Remove the eyelet cover using a flathead screwdriver. To protect the bodywork, place a rag between the screwdriver and the vehicle body, as shown in the illustration.
5-1. Essential information STEP 2 Insert the towing eyelet into the hole and tighten partially by hand. STEP 3 Tighten down the towing eyelet securely using a wheel nut wrench. Location of the emergency towing eyelet P. 371, 380 CAUTION Installing towing eyelets to the vehicle Make sure that towing eyelet is installed securely. If not securely installed, towing eyelets may come loose during towing. This may lead to accidents that cause serious injury or even death.
5-1. Essential information Towing with a sling-type truck NOTICE To prevent body damage Do not tow with a sling-type truck, either from the front or rear. Towing with a wheel lift-type truck From the front Vehicles with an automatic transmission: Use a towing dolly under the rear wheels. 5 When trouble arises Vehicles with a manual transmission: We recommend using a towing dolly under the rear wheels. When not using a towing dolly, release the parking brake and shift the shift lever to N.
5-1. Essential information From the rear Vehicles without a smart entry & start system: Turn the engine switch to the “ACC” position so that the steering wheel is unlocked. Vehicles with a smart entry & start system: Turn the “ENGINE START STOP” switch to ACCESSORY mode so that the steering wheel is unlocked.
5-1. Essential information Using a flat bed truck If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45. Do not overly tighten the tie downs or the vehicle may be damaged.
5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional as soon as possible. Visible symptoms Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.
5-1. Essential information Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or an airbag inflates upon collision, the fuel pump shut off system stops supplying fuel to the engine. Follow the procedure below to restart the engine after the system is activated. Vehicles without a smart entry & start system STEP 1 Turn the engine switch to the “ACC” or “LOCK” position. STEP 2 Restart the engine.
5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds... Calmly perform the following actions if any of the warning lights turn on or flash. If a light turns on or flashes, but then turns off, this does not necessarily indicate a malfunction in the system. Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake system.
5-2. Steps to take in an emergency Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional immediately. Warning light 5 When trouble arises (Flashes in yellow for 15 seconds.
5-2. Steps to take in an emergency Warning light (Comes on in yellow) Warning light/Details Cruise control indicator light (if equipped) Indicates a malfunction in the cruise control system. If the malfunction indicator lamp comes on while driving The malfunction indicator lamp will come on if the fuel tank becomes completely empty. If the fuel tank is empty, refuel the vehicle immediately. The malfunction indicator lamp will go off after several trips.
5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light turns off. Warning light (On the instrument cluster) (On the center panel) Automatic transmission fluid temperature warning light (if equipped) Indicates that the automatic transmission fluid temperature is too high. Correction procedure Check that both side doors and the trunk are closed. Refuel the vehicle. Fasten the seat belt.
5-2. Steps to take in an emergency * : Driver's and front passenger’s seat belt buzzer: The driver’s and front passenger’s seat belt buzzer sounds to alert the driver and front passenger that his or her seat belt is not fastened. The buzzer sounds for 30 seconds after the vehicle has reached a speed of at least 20 km/h (12 mph). Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 90 more seconds.
5-2. Steps to take in an emergency Follow the correction procedures. (vehicles with a smart entry & start system) After taking the specified steps to correct the suspected problem, check that the warning light goes off.
5-2. Steps to take in an emergency Interior buzzer Once Once 368 FT86_EE Exterior buzzer 3 times 3 times Warning light (Flashes in yellow) (Flashes in yellow) Warning light/Details Correction procedure Smart entry & start system indicator light Vehicles with an automatic transmission: The electronic key was carried outside the vehicle and the driver’s door was opened and closed while the shift position P was selected without turning off the “ENGINE START STOP” switch.
5-2. Steps to take in an emergency Interior buzzer Once Once Intermittently (7 seconds) Once Continuous (10 seconds) Warning light Warning light/Details Correction procedure Smart entry & start system indicator light An attempt was made to exit the vehicle with the electronic key and lock the doors without first turning the “ENGINE START STOP” switch off. Turn the “ENGINE START STOP” switch off and lock the doors again. (Flashes in yellow for 15 seconds.
5-2. Steps to take in an emergency Interior buzzer Once 370 FT86_EE Exterior buzzer Warning light (Flashes in yellow for 15 seconds.) Warning light/Details Correction procedure Smart entry & start system indicator light The electronic key could not be detected in the vehicle even after the “ENGINE START STOP” switch was pressed once. Vehicles with an automatic transmission: Touch the electronic key to the “ENGINE START STOP” switch while depressing the brake pedal.
5-2. Steps to take in an emergency If you have a flat tire (vehicles with a spare tire) Remove the flat tire and replace it with the spare provided. Before jacking up the vehicle Stop the vehicle on a hard, flat surface. Set the parking brake. Shift the shift lever to P (vehicles with an automatic transmission) or R (vehicles with a manual transmission). Stop the engine. Turn on the emergency flashers.
5-2. Steps to take in an emergency Taking out the spare tire Loosen the center fastener that secures the spare tire. Replacing a flat tire STEP 1 Chock the tires.
5-2. Steps to take in an emergency STEP 2 Slightly loosen the wheel nuts (one turn). STEP 3 Turn the tire jack portion “A” by hand until the notch of the jack is in contact with the jack point. STEP 4 Raise the vehicle until the tire is slightly raised off the ground. 5 When trouble arises STEP 5 Remove all the wheel nuts and the tire. When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface.
5-2. Steps to take in an emergency Installing the spare tire Remove any dirt or foreign matter from the wheel contact surface. STEP 1 If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle. STEP 2 STEP 3 374 FT86_EE Tapered portion Install the spare tire and loosely tighten each wheel nut by hand to approximately the same amount.
5-2. Steps to take in an emergency Firmly tighten each nut two or three times in the order shown in the illustration. STEP 4 Tightening torque: 120 N•m (12.2 kgf•m, 89 ft•lbf) STEP 5 Stow the flat tire, tire jack and all tools. Storing the tire Always install the center fastener as shown in the illustration.
5-2.
5-2. Steps to take in an emergency CAUTION Using the tire jack Improper use of the tire jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack. Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains. Only use the tire jack that comes with this vehicle for replacing a flat tire. Do not use it on other vehicles, and do not use other tire jacks for replacing tires on this vehicle.
5-2. Steps to take in an emergency CAUTION Replacing a flat tire Do not touch the disc wheels or the area around the brakes immediately after the vehicle has been driven. After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot. Touching these areas with hands, feet or other body parts while changing a tire, etc. may result in burns. Do not attach a heavily damaged wheel ornament, as it may fly off the wheel while the vehicle is moving.
5-2. Steps to take in an emergency If you have a flat tire (vehicles with an emergency tire puncture repair kit) A puncture caused by a nail or screw passing through the tire tread can be repaired temporarily using the emergency tire puncture repair kit. (The kit contains a bottle of sealant. The sealant can be used only once to temporarily repair one tire without removing the nail or screw from the tire.) Depending on the damage, this kit cannot be used to repair the tire. (P.
5-2. Steps to take in an emergency Location of the emergency tire puncture repair kit, jack and tools Jack handle Towing eyelet Emergency tire puncture repair kit Jack* Wheel nut wrench Screwdriver *: Use of the jack (P.
5-2. Steps to take in an emergency Before performing emergency repair Check the degree of the tire damage. • Do not remove the nail or screw from the tire. Removing the object may widen the opening and prevent emergency repair with the repair kit. • To avoid sealant leakage, move the vehicle until the area of the puncture, if known, is positioned at the top of the tire.
5-2. Steps to take in an emergency In the following cases, the tire cannot be repaired with the emergency tire puncture repair kit. Contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional.
5-2. Steps to take in an emergency Emergency repair method STEP 1 Shake the sealant bottle up and down several times and remove the cap of the sealant bottle. STEP 2 Connect the injection hose by screwing onto the sealant. As it is screwed in, the aluminum seal on the bottle will be torn. Injection hose Sealant Position the nail or screw that has punctured the tire at the bottom, in contact with the ground. Remove the cap from the valve.
5-2. Steps to take in an emergency Pull out the valve core by turning it counterclockwise using the valve core tool. STEP 5 Valve core Remove the plug from the injection hose. STEP 6 Plug Injection hose STEP 7 Valve Connect the injection hose to the valve. Injection hose STEP 8 384 FT86_EE Inject the sealant that is in the bottle. Hold and tilt the bottle, then squeeze sealant out of the bottle as shown.
5-2. Steps to take in an emergency STEP 9 Valve core tool Remove the injection hose from the valve and screw the valve core in the valve securely by turning it clockwise with the valve core tool. Valve core STEP 10 Attach the sticker as shown. Remove any dirt and moisture from the wheel before attaching the label.
5-2. Steps to take in an emergency STEP 12 Connect the compressor power plug to the power outlet. Power plug Vehicles without a smart entry & start system: The engine switch must be in the “ACC” position. Power outlet Connect the air compressor hose by threading it on the valve. STEP 13 Hose STEP 14 Vehicles with a smart entry & start system: The “ENGINE START STOP” switch must be in ACCESSORY mode. Compressor Left-hand drive vehicles: Check the specified inflation pressure.
5-2. Steps to take in an emergency Turn the compressor switch “ON” and fill the tire with air until the specified inflation pressure is reached. STEP 15 Switch STEP 16 Turn the switch “OFF” when the pressure gauge connected to the hose reads the specified pressure. If the inflation pressure is not attained within 10 minutes, emergency repair is not possible due to severe damage. Contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional.
5-2. Steps to take in an emergency STEP 20 Read the inflation pressure on the pressure gauge. If the pressure is 130 kPa (1.3 kgf/cm2 or bar, 19 psi) or above, fill the tire with air using the compressor until the specified inflation pressure is reached. If the pressure is less than 130 kPa (1.3 kgf/cm2 or bar, 19 psi), the emergency repair that have been performed is not safe for use as damage to the tire is too severe. Do not continue to drive the vehicle.
5-2. Steps to take in an emergency The valve of a tire that has been repaired After a tire is repaired with the emergency tire puncture repair kit, the valve should be replaced. Note for checking the emergency tire puncture repair kit Check the sealant expiry date occasionally. The expiry date is shown on the bottle. Do not use sealant whose expiry date has already passed. Otherwise, repairs conducted using the emergency tire puncture repair kit may not be performed properly.
5-2. Steps to take in an emergency CAUTION Do not drive the vehicle with a flat tire Do not continue driving with a flat tire. Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair. Driving with a flat tire may cause a circumferential groove on the side wall. In such a case, the tire may explode when using a repair kit. Caution while driving Store the repair kit in the trunk. Injuries may result in the event of an accident or sudden braking.
5-2. Steps to take in an emergency CAUTION When fixing the flat tire Stop your vehicle in a safe and flat area. If force is used to turn the valve core tool while air remains in the tire, special care should be taken because the valve core could fly out. Be careful, as sealant may fly out if you shake the bottle with the hose installed. Do not touch the wheels or the area around the brakes immediately after the vehicle has been driven.
5-2. Steps to take in an emergency CAUTION When fixing the flat tire After inflation of the tire has completed, the sealant may splatter when the hose is disconnected or some air is let out of the tire. Follow the operation procedure to repair the tire. If the procedures not followed, the sealant may spray out. Keep back from the tire while it is being repaired, as there is a chance of it bursting while the repair operation is being performed.
5-2. Steps to take in an emergency NOTICE When performing an emergency repair A tire should only be repaired with the emergency tire puncture repair kit if the damage is caused by a sharp object such as nail or screw passing through the tire tread. Do not remove the sharp object from the tire. Removing the object may widen the opening and disenable emergency repair with the repair kit. The repair kit is not waterproof.
5-2. Steps to take in an emergency If the engine will not start If the engine will not start even though correct starting procedures are being followed (P. 165, 174), consider each of the following points. The engine will not start even when the starter motor operates normally. One of the following may be the cause of the problem. There may not be sufficient fuel in the vehicle’s tank. Refuel the vehicle. The engine may be flooded.
5-2. Steps to take in an emergency The starter motor does not turn over, the interior lights and headlights do not turn on, or the horn does not sound. One of the following may be the cause of the problem. One or both of the battery terminals may be disconnected. The battery may be discharged. (P. 403) There may be a malfunction in the steering lock system.
5-2. Steps to take in an emergency Vehicles with a manual transmission STEP 1 Set the parking brake. STEP 2 Put the shift lever in N. STEP 3 Turn the “ENGINE START STOP” switch to ACCESSORY mode. STEP 4 Push and hold the “ENGINE START STOP” switch for about 15 seconds while depressing the brake pedal and clutch pedal firmly. Even if the engine can be started using the above steps, the system may be malfunctioning.
5-2. Steps to take in an emergency If the shift lever cannot be shifted from P (vehicles with an automatic transmission) If the shift lever cannot be shifted with your foot on the brake, there may be a problem with the shift lock system (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional immediately.
5-2. Steps to take in an emergency If you lose your keys New genuine keys can be made by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. For vehicles without a smart entry & start system, bring a master key and the key number stamped on the key number plate. For vehicles with a smart entry & start system, bring the other key and the key number stamped on the key number plate.
5-2. Steps to take in an emergency If the electronic key does not operate properly (vehicles with a smart entry & start system) If communication between the electronic key and vehicle is interrupted (P. 38) or the electronic key cannot be used because the battery is depleted, the smart entry & start system and wireless remote control cannot be used. In such cases, the doors and trunk can be opened or the engine can be started by following the procedure below.
5-2. Steps to take in an emergency Starting the engine Vehicles with an automatic transmission STEP 1 Ensure that the shift lever is in P and firmly depress the brake pedal. STEP 2 Touch the Toyota emblem side of the electronic key to the “ENGINE START STOP” switch. When the electronic key is detected, a buzzer sounds and the “ENGINE START STOP” switch will turn to IGNITION ON mode.
5-2. Steps to take in an emergency Vehicles with a manual transmission STEP 1 Ensure that the shift lever is in N and depress the clutch pedal. STEP 2 Touch the Toyota emblem side of the electronic key to the “ENGINE START STOP” switch. When the electronic key is detected, a buzzer sounds and the “ENGINE START STOP” switch will turn to IGNITION ON mode. When the smart entry & start system is deactivated in customization setting, the “ENGINE START STOP” switch will turn to ACCESSORY mode.
5-2. Steps to take in an emergency Stopping the engine Vehicles with an automatic transmission: Shift the shift lever to P and press the “ENGINE START STOP” switch as you normally do when stopping the engine. Vehicles with a manual transmission: Shift the shift lever to N and press the “ENGINE START STOP” switch as you normally do when stopping the engine.
5-2. Steps to take in an emergency If the battery is discharged The following procedures may be used to start the engine if the vehicle's battery is discharged. You can call any authorized Toyota dealer or repairer, or another duly qualified and equipped professional or a qualified repair shop. If you have a set of jumper (or booster) cables and a second vehicle with a 12-volt battery, you can jump start your vehicle following the steps below.
5-2. Steps to take in an emergency Right-hand drive vehicles Positive (+) battery terminal on your vehicle Positive (+) battery terminal on the second vehicle Negative (-) battery terminal on the second vehicle Connect the jumper cable to ground on your vehicle as shown in the illustration. STEP 2 Start the engine of the second vehicle. Increase the engine speed slightly and maintain at that level for approximately 5 minutes to recharge the battery of your vehicle.
5-2. Steps to take in an emergency STEP 5 Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were connected. Once the engine starts, have the vehicle checked at any authorized Toyota dealer or repairer, or another duly qualified and equipped professional as soon as possible. Starting the engine when the battery is discharged The engine cannot be started by push-starting.
5-2. Steps to take in an emergency The “ENGINE START STOP” switch mode is memorized by the vehicle. When the battery is reconnected, the system will return to the mode it was in before the battery was discharged. Before disconnecting the battery, turn the “ENGINE START STOP” switch off. If you are unsure what mode the “ENGINE START STOP” switch was in before the battery discharged, be especially careful when reconnecting the battery.
5-2. Steps to take in an emergency CAUTION To prevent damage to the vehicle Do not pull- or push-start the vehicle as the three-way catalytic converter may overheat and become a fire hazard. NOTICE When handling jumper cables Be careful that the jumper cables do not become tangled in the cooling fans or any of the belts when connecting or disconnecting them. When closing the doors While pushing the door glass towards the inside of the vehicle, slowly close the door.
5-2. Steps to take in an emergency If your vehicle overheats If your engine overheats: STEP 1 Stop the vehicle in a safe place and turn off the air conditioning system. STEP 2 Check to see if steam is coming out from under the hood. If you see steam: Stop the engine. Carefully lift the hood after the steam subsides and then restart the engine. If you do not see steam: Leave the engine running and carefully lift the hood. STEP 3 Check to see if the cooling fan is operating.
5-2. Steps to take in an emergency STEP 5 Add engine coolant if necessary. Water can be used in an emergency if engine coolant is unavailable. (P. 423) Have the vehicle checked at the nearest authorized Toyota dealer or repairer, or another duly qualified and equipped professional as soon as possible. Overheating If you observe the following, your vehicle may be overheating. The engine coolant temperature gauge enters the red zone or a loss of power is experienced.
5-2. Steps to take in an emergency NOTICE When adding engine coolant Wait until the engine has cooled down before adding engine coolant. When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine.
5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow: STEP 1 Stop the engine. Set the parking brake and shift the shift lever to P (vehicles with an automatic transmission) or N (vehicles with a manual transmission). STEP 2 Remove the mud, snow or sand from around the rear wheels. STEP 3 Place wood, stones or some other material under the rear wheels to help provide traction.
5-2. Steps to take in an emergency CAUTION When attempting to free a stuck vehicle If you choose to push the vehicle back and forth to free it, make sure the surrounding area is clear to avoid striking other vehicles, objects or people. The vehicle may also lunge forward or lunge back suddenly as it becomes free. Use extreme caution. When shifting the shift lever For vehicles with an automatic transmission, be careful not to shift the shift lever with the accelerator pedal depressed.
5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following procedure: STEP 1 Steadily step on the brake pedal with both feet and firmly depress it. Do not pump the brake pedal repeatedly as this will increase the effort required to slow the vehicle. STEP 2 Shift the shift lever to N.
5-2. Steps to take in an emergency STEP 4 Press and hold for 3 seconds or more, or press briefly 3 times or more STEP 5 Vehicles with a smart entry & start system: To stop the engine, press and hold the “ENGINE START STOP” switch for 3 consecutive seconds or more, or press it briefly 3 times or more in succession. Stop the vehicle in a safe place by the road.
Vehicle specifications 6 6-1. Specifications Maintenance data (fuel, oil level, etc.).......... 416 Fuel information ................ 428 6-2. Customization Customizable features ......
6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions and weight Overall length 4240 mm (166.9 in.)*2 4255 mm (167.5 in.)*3 Overall width 1775 mm (69.9 in.)*2 1795 mm (70.6 in.)*3 Overall height*1 1425 mm (56.1 in.) Wheelbase 2570 mm (101.2 in.) Tread Front 1520 mm (59.8 in.) Rear 1540 mm (60.6 in.) Details are described on the manufacturer’s label. (P. 417) Gross vehicle mass Maximum permissible axle capacity Front 876 kg (1931 lb.) Rear 943 kg (2079 lb.
6-1. Specifications Vehicle identification Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped under the right-hand front seat. This number is located on the top left of the body panel. This number is also on the manufacturer’s label.
6-1. Specifications Engine number The engine number is stamped on the engine block as shown.
6-1. Specifications Engine Model FA20 Type Horizontally opposed, liquid cooled 4 cylinder, 4stroke gasoline Bore and stroke 86.0 86.0 mm (3.39 3.39 in.) Displacement 1998 cm3 (121.93 cu.in.) Drive belt tension Automatic adjustment Fuel Fuel type EU area: Unleaded gasoline conforming to European standard EN228 only Except EU area: Unleaded gasoline only Research octane number 98 or higher* Fuel tank capacity (Reference) 50 L (13.2 gal., 11.0 Imp. gal.
6-1. Specifications Lubrication system Oil capacity (Drain and refill reference*) Without filter With filter *: 5.2 L (5.5 qt., 4.6 Imp. qt.) 5.4 L (5.7 qt., 4.8 Imp. qt.) The engine oil capacity is a reference quantity to be used when changing the engine oil. Warm up and turn off the engine, wait more than 5 minutes, and check the oil level on the dipstick. Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle.
6-1. Specifications Recommended viscosity (SAE): Preferred Temperature range anticipated before next oil change SAE 0W-20 is filled into your Toyota vehicle at manufacturing, and the best choice for good fuel economy and good starting in cold weather. If SAE 0W-20 oil is not available, SAE 5W-30 oil may be used. However, it should be replaced with SAE 0W-20 at the next oil change.
6-1. Specifications How to read oil container labels: Either or both API registered marks are added to some oil containers to help you select the oil you should use. API Service Symbol Top portion: The oil quality designation by API (American Petroleum Institute) (SN) Center portion: The SAE viscosity grade (SAE 0W-20) Lower portion: “Resource-Conserving” means that the oil has fuel saving and environmental protection.
6-1. Specifications Cooling system Capacity Vehicles with an automatic transmission 7.5 L (7.9 qt., 6.6 Imp. qt.) Vehicles with a manual transmission 7.2 L (7.6 qt., 6.3 Imp. qt.) Coolant type Use either of the following. • “TOYOTA Genuine 50/50 Pre-mixed Super Long Life Coolant BLUE” • Similar high-quality ethylene glycol-based nonsilicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
6-1. Specifications Electrical system Battery Specific gravity reading at 20C (68F): 1.250 1.290 Fully charged 1.160 1.200 Half charged 1.060 1.100 Discharged Charging rates Quick charge Slow charge 15 A max. 5 A max. Differential Oil capacity (Reference) 1.15 L (1.22 qt., 1.01 Imp. qt.
6-1. Specifications Automatic transmission Fluid capacity* 7.5 L (7.9 qt., 6.6 Imp. qt.) Fluid type TOYOTA Genuine ATF WS *: The fluid capacity is provided as a reference. If replacement is necessary, contact any authorized Toyota dealer or repairer, or another duly qualified and equipped professional.
6-1. Specifications Clutch Pedal free play 5 15 mm (0.2 0.6 in.) Fluid type FMVSS No.116 fresh DOT 3 or DOT 4 brake fluid Brakes Pedal clearance*1 55.0 mm (2.16 in.) min. Pedal free play 0.2 2.0 mm (0.008 0.079 in.) Parking brake lever travel*2 7 8 clicks Fluid type FMVSS No.116 fresh DOT 3 or DOT 4 brake fluid *1: Minimum pedal clearance when depressed with a force of 490 N (50 kgf, 110 lbf) while the engine is running.
6-1.
6-1. Specifications Fuel information The engine is designed to operate at maximum performance using unleaded gasoline with an octane rating of 98 or higher. If 98 RON fuel is not readily available in your area, unleaded gasoline with an octane rating of 95 RON may be used with no detriment to engine durability or driveability. However, you may notice a slight decrease in maximum engine performance and you may hear some knocking (pinking) of an engine while using 95 RON fuel.
6-1. Specifications NOTICE Notice on fuel quality Do not use improper fuels. If improper fuels are used the engine will be damaged. Do not use leaded gasoline. Leaded gasoline will cause the three-way catalytic converter to lose its effectiveness and the emission control system to function improperly. EU area: Bioethanol fuel sold under names such as “E50” or “E85” and fuel containing a large amount of ethanol should not be used. The use of these fuels will damage the vehicle's fuel system.
6-2. Customization Customizable features Your vehicle includes a variety of electronic features that can be personalized to your preferences. Programming these preferences requires specialized equipment and may be performed by any authorized Toyota dealer or repairer, or another duly qualified and equipped professional. Some function settings are changed simultaneously with other functions being customized.
6-2. Customization Item Function Default setting Customized setting Push and hold (long) Wireless remote control (P. 47) Trunk unlocking operation Automatic light control system (P. 205) Light sensor sensitivity Lights (P.
6-2.
Index Abbreviation list ...................... 434 Alphabetical index................... 435 What to do if... .........................
Abbreviation list Abbreviation/Acronym list ABBREVIATIONS 434 FT86_EE MEANING ABS Anti-lock Brake System ACC Accessory AI-SHIFT Artificial Intelligence Shift CRS Child Restraint System DISP Display ECU Electronic Control Unit EDR Event Data Recorder ELR Emergency Locking Retractor EPS Electric Power Steering LED Light Emitting Diode LSD Limited Slip Differential SRS Supplemental Restraint System TRC Traction Control VIN Vehicle Identification Number VSC Vehicle Stability Co
Alphabetical index Alphabetical index A A/C..................................... 236, 244 ABS ........................................... 222 Air conditioning filter .............. 318 Air conditioning system Air conditioning filter.............. 318 Automatic air conditioning system ................................ 244 Manual air conditioning system ................................ 236 Airbags Airbag manual on/off system ................................ 148 Airbag operating conditions ...................
Alphabetical index B Back-up lights Replacing light bulbs............. 332 Wattage................................. 427 Battery Checking ............................... 305 If the vehicle has a discharged battery .............. 403 Preparing and checking before winter.......................229 Bottle holders........................... 259 Brake Parking brake........................ 188 Brake assist.............................. 222 Break-in tips .............................
Alphabetical index D Daytime running light system .................................... 208 Defogger Rear window ......................... 252 Side mirror ............................ 252 Dimension ................................ 416 Display Multi-information display ....... 200 Trip information ..................... 201 Do-it-yourself maintenance .... 291 Door courtesy lights Door courtesy lights .............. 255 Wattage................................. 427 Doors Door lock.....................
Alphabetical index Engine Compartment ........................ 298 Engine switch................ 165, 174 Hood ..................................... 294 How to start the engine......................... 165, 174 Identification number............. 417 If the engine will not start ...... 394 Ignition switch ...............165, 174 Overheating .......................... 408 Engine coolant Capacity ................................ 423 Checking ...............................
Alphabetical index G Gauges...................................... 190 Glove box ................................. 258 H Hazard lights Switch ................................... 352 Head restraints Adjusting ................................ 64 Headlight cleaner..................... 214 Headlights Discharge headlight precautions ......................... 349 Replacing light bulbs............. 332 Switch ................................... 205 Wattage.................................
Alphabetical index K Keyless entry ............................. 47 M Maintenance Do-it-yourself maintenance... 291 Maintenance data ................. 416 Maintenance requirements ... 288 Manual air conditioning system.................................... 236 Manual transmission............... 184 Meter Instrument panel light control ......................... 193 Meters................................... 190 Mirrors Inside rear view mirror ............ 74 Side mirror heater .................
Alphabetical index P Parking brake ........................... 188 Power outlets ........................... 267 Power windows.......................... 78 R Radiator .................................... 304 Rear fog lights Replacing light bulbs............. 332 Switch ................................... 212 Wattage................................. 427 Rear seats................................... 62 Rear turn signal lights Replacing light bulbs............. 332 Switch ..................................
Alphabetical index Seats Adjustment .............................. 58 Adjustment precautions .......... 61 Child seats/child restraint system installation .............. 133 Cleaning................................ 282 Head restraint .........................64 Properly sitting in the seat....... 94 Seat heaters.......................... 269 Service reminder indicators .............................. 195 Shift lever Automatic transmission......... 177 If the shift lever cannot be shifted from P ............
Alphabetical index T Tachometer Tachometer........................... 190 Tail lights Switch ................................... 205 Theft deterrent system Double locking system ............ 92 Engine immobilizer system ..... 85 Tire inflation pressure ............. 426 Tires Chains................................... 229 Checking ............................... 311 Emergency tire puncture repair kit.............................. 379 If you have a flat tire...... 371, 379 Inflation pressure ...............
Alphabetical index 444 FT86_EE U USB port ................................... 254 V Vanity lights Vanity lights........................... 263 Wattage................................. 427 Vanity mirrors .......................... 263 Vehicle identification number ................................... 417 Vehicle stability control .......... 222 VSC ........................................... 222 “VSC SPORT” mode................ 223 W Warning buzzers Electric power steering .........
Alphabetical index Washing and waxing ............... 278 Wheels ...................................... 316 Window glasses ........................ 78 Window lock switch................... 78 Windows Power windows ....................... 78 Rear window defogger .......... 252 Washer.................................. 214 Windshield wipers ................... 214 Wireless remote control key Locking/Unlocking................... 47 Replacing the battery ............ 320 Wireless remote control key....
What to do if... What to do if... A tire punctures P. 371 If you have a flat tire P. 379 P. 394 If the engine will not start The engine does not start P. 85 Engine immobilizer system P. 403 If the battery is discharged The shift lever cannot be moved out P. 397 If the shift lever cannot be shifted from P The engine coolant temperature gauge enters the P. 408 If your vehicle overheats Steam can be seen coming from under the hood 446 FT86_EE The key is lost P.
What to do if... Warning lights Brake system warning light P. 362 Slip indicator Charging system warnP. 362 ing light Automatic headlight leveling sysP. 363 tem warning light Low engine oil pressure P. 362 warning light Cruise control indicator light* P. 363 Malfunction indicator lamp P. 363 Open door warning light SRS warning light Low fuel level warning P. 365 light P. 363 ABS warning light P. 363 P. 365 P. 363 Driver’s seat belt reminder light P.
GAS STATION INFORMATION Fuel filler door P. 81 Tire inflation pressure P. 426 Fuel tank capacity (Reference) Fuel type Cold tire inflation pressure Engine oil capacity (Drain and refill reference) Engine oil type 448 FT86_EE Trunk opener P. 53 Fuel filler door opener P. 81 Auxiliary catch lever P. 294 Hood lock release lever P. 294 50 L (13.2 gal., 11.0 Imp. gal.) Unleaded gasoline only P. 81, 419 P. 426 Without filter With filter L (qt., Imp. qt.) 5.2 (5.5, 4.6) 5.4 (5.7, 4.8) P.
