ASSEMBLY INSTRUCTIONS METAL GARDEN SHED E-mail: hofficeservice@gmail.com Metal Garden House Installation Tutorial https://youtu.
SITE PREPARATION Level the ground surface. ent cem Recommendation: Construct a wooden or concrete base as a foundation. The external dimensions of the product : 71.1’’ 61’’ 34.
BEFORE STARTING ASSEMBLY Remove all of the pieces from the package and spread them out on the ground. Before installation, please check the type and quantity of parts first. It is recommended to use a clean work surface to spread the parts out and for pre-assembly steps. Review all instructions before you begin, continue to refer to instructions during assembly. Be sure to follow all steps thoroughly. Please prepare these components in advance at the beginning of each stage.
ROOF PARTS P1 X2 P2 X1 P3 X1 M4 X2 S3 X1 S4 X1 S2 X1 GC X4 M3 X4 04
WALL PARTS W1A X5 W2A X4 W3A X1 BR X1 B1 X1 URA X1 BL X1 B2 X1 V1 X80 V2 X150 L3 X1 L1 X1 L2 X1 UP1 X1 05 ULA X1
DOOR PARTS DL1 X1 20 X2 DH X2 DG X1 DX1 X2 DF X1 DR1 X1 SCREW cm 1 inch 2 0.5 3 1 inch 1 M4*10 2 0.5 F3(X16) 3 1 1 inch 1.5 F1(X160) cm cm 4 2 3 0.5 4 1 1.5 F2(X8) cm 4 For GC 1.5 M5*12 inch 1 2 0.5 F5(X4) 06 M4*10 3 1 4 1.
GC M3 M3 GC M4 P1 P2 P3 P1 GC M4 M3 M3 GC S4 S3 S2 L3 L2 UP1 L1 W2A W1A W1A W1A W2A W2A W1A 20 DX1 DH W2A DR1 DL1 W1A W3A URA DF DG ULA DX1 DH 20 B2 BR BL 07 B1
CONTENTS Bottom frame 09-10 (page) Wall 11-18 (page) Roof 19-21 (page) Door 22-24 (page) 08
STEP 1 F1 BL B1 BL B1 F1 X2 STEP 2 F1 B2 BL B2 BL B1 09 F1 X2
STEP 3 F1 B2 BR B2 BR BL B1 BR B1 STEP 4 F1 Tips: Align the gasket with the hole, and then use the electric drill to drill the V2 into the hole.
STEP 5 Please align the screws with the screw holes for installation.
STEP 7 F1 V2 BR W2A BL B1 F1 X4 V2 X4 STEP 8 W2A V2 BL F1 B2 BR B1 12 F1 X3 V2 X3
STEP 9 L3 B1 L3 V2 B2 F1 F1 V2 Tips: Pay attention to distinguishing F1 X6 the direction when installing. V2 X6 STEP 10 L2 L1 L1 V2 F1 L1 B1 V2 B2 F1 Tips: Pay attention to distinguishing the direction when installing.
STEP 11 L1 L2 V2 F1 B2 L2 V2 F1 B1 Tips: Pay attention to distinguishing the direction when installing.
STEP 13 L2 W1A L1 B1 B2 F1 X8 V2 X8 STEP 14 L2 L1 W1A W1A V2 F1 B2 15 F1 X16 V2 X16
STEP 15 W1A V2 F1 X4 F1 V2 X4 STEP 16 URA URA V2 F1 V2 Tips: Internal setup.
STEP 17 B1 B2 UP1 V2 V2 F1 F1 F1 X5 V2 X5 STEP 18 V2 UP1 F1 V2 F1 URA Tips: Internal setup.
STEP 19 W3A V2 V2 F1 F1 F1 X4 V2 X4 STEP 20 F1 V2 F1 ULA V2 V2 ULA ULA F1 Tips: Internal setup.
STEP 21 F1 V2 F1 V2 S2 Tips: Internal setup.
STEP 23 F1 V2 S4 S4 F2 S4 V2 V2 X5 F1 X4 F1 V2 F2 X1 STEP 24 F1 V2 P1 P1 P3 P1 P3 P1 P1 P1 P2 When installing P1, please note that these two holes need to be aligned installed.
STEP 25 F1 M3 V2 M3 M3 F1 M3 M3 V2 M3 F1 X2 V2 X2 STEP 26 F5 GC F5 M4 GC M4 M4 M3 21 F5 X4
STEP 27 20 DX1 DL1 DG DR1 DX1 20 STEP 28 20 20 22
STEP 29 F1 V2 DG F2 DG F1 X8 V2 X8 F2 X6 STEP 30 20 DX1 F1 DX1 20 23 F1 X6 V2 X6
STEP 31 DH F3 X2 DH F3 X8 STEP 32 F3 X2 DF F1 24 F1 X2 F3 X8
STEP 33 V1 V2 F1 Put it on the screw tip to prevent injury.
CARE & SAFETY • Unsuitable for storage of flammable or corrosive substances. • It is of utmost importance to assemble all of the parts according to the directions. Do not skip any step. • Please consult your local authorities if any permits are required to erect shed. • Periodically check shed to assure that it remains stable and that the site remains level.
