User's Manual

ManualsBrandsTP-Link Technologies ManualsElectronicsAC2600 Wireless Dual Band Gigabit Router

Table Of Contents

Chapter 1. Get to Know About Your Router
- 1.1 Product Overview
- 1.2 Main Features
- 1.3 Panel Layout
Chapter 2. Connect the Hardware
- 2.1 Requirements for Operation
- 2.2 Position Your Router
- 2.3 Connect Your Router
Chapter 3. Log into Your Router
Chapter 4. Set Up Internet Connection
- 4.1 Use Quick Setup Wizard
- 4.2 Manually Set up an Internet Connection
- 4.3 Set up IPv6 Connection
Chapter 5. Guest Network
Chapter 6. USB Application
- 6.1 Device Settings
- 6.2 Sharing Access
- 6.3 Printer Sever
Chapter 7. Parental Controls
Chapter 8. Security
- 8.1 Settings
- 8.2 Access Control
- 8.3 IP & MAC Binding
Chapter 9. NAT Forwarding
- 9.1 Share Local Resources in the Internet by ALG
- 9.2 Share Local Resources in the Internet by Virtual Server
- 9.3 Open Ports Dynamically by Port Triggering
- 9.4 Make Applications Free from Port Restriction by DMZ
- 9.5 Make Xbox Online Games Run Smoothly by UPnP
Chapter 10. QoS
Chapter 11. Specify the Network Settings
- 11.1 Change LAN Settings
  - 11.1.1 Change the LAN IP address
- 11.2 Configure to support IPTV service
- 11.3 Specify DHCP Server Settings
- 11.4 Dynamic DNS
- 11.5 Static Routing
- 11.6 Specify Wireless Settings
- 11.7 WPS
4. Enter the username, password and domain name of the account (such as lisadns.ddns.net).
5. Click Login and Save.
1. Change the routers LAN IP addresses to two different IP addresses on the same subnet. Disable Router 2’s DHCP function.
2. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. Go to Network →Advanced Routing. Click Add to add a new static routing entry.
- Allow all LAN connected devices to manage the router
- Allow specific devices to manage the router
Chapter 12. Administrate Your Network
- 12.1 Set Up System Time
- 12.2 Test the Network Connectivity
- 12.3 Upgrade the Firmware
- 12.4 Backup and Restore Configuration Settings
- 12.5 Change the Administrator Account
- 12.6 Password Recovery
- 12.7 Local Management
- 12.8 Remote Management
- 12.9 System Log
- 12.10 Reboot the Router
- 12.11 Logout
Visit http://tplinkwifi.net, and log in with the username and password you set for the router.
Go to Advanced > System Tools > Administration. In Remote Management section, finish the settings according to your needs.
- Forbid all devices to manage the router remotely:
- Allow all devices to manage the router remotely:
- Allow specific devices to manage the router remotely:
Appendix A: Specifications
Appendix B: Troubleshooting Guide & FAQ
Appendix C: Configure the PC

mode. Please refer to Note 2 for troubleshooting.

(Wireless)

The wireless 2.4GHz band is working properly.

Off

The wireless 2.4 GHz band is disabled.

(Wireless)

The wireless 5GHz band is working properly.

Off

The wireless 5GHz band is disabled.

(LAN)

At least one LAN port is connected.

Off

No LAN port is connected.

(WPS)

A wireless device has been successfully added to the network by WPS

function.

Flash

WPS handshaking is in process and will continue for about 2 minutes. Please

press the WPS button on other wireless devices that you want to add to the

network while the LED is flashing.

Off

A wireless device has failed to be added to the network by WPS function.

(USB)

The USB device is identified and ready to use.

Flash

The USB device is being identified.

Off

No USB device is plugged into the USB port.

Note:

1. After a device is successfully added to the network by WPS function, the WPS LED will keep on for about 5 minutes and

then turn off.

Chapter 1 Get to Know About Your Router5