User Guide Wireless N Access Point EAP110/EAP120/EAP220 REV1.0.
EAP110 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s).
NCC Notice & BSMI Notice 注意！ 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自 變更頻率、加大功率或變更原設計之特性或功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時， 應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電 信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。 減少電磁波影響，請妥適使用。 安全諮詢及注意事項 ●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ●注意防潮，請勿將水或其他液體潑灑到本產品上。 ●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 ●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況
Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations.
FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.
5150-5250 MHz Country Restriction Reason/remark Bulgaria Not implemented Planned Croatia License required General authorization required if used outside own Italy premises Luxembourg None Russian Federation No info General authorization required for network and service supply (not for spectrum) Note: Please don’t use the product outdoors in France. IC STATEMENT This Class A digital apparatus complies with Canadian ICES-003.
NCC Notice & BSMI Notice 注意！ 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自 變更頻率、加大功率或變更原設計之特性或功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時， 應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電 信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。 減少電磁波影響，請妥適使用。 安全諮詢及注意事項 ●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ●注意防潮，請勿將水或其他液體潑灑到本產品上。 ●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 ●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下
About this User Guide This User Guide is for EAP110, EAP120 and EAP220. Chapter 4 to Chapter 8 are only suitable for the EAP in Standalone mode. Refer to the EAP Controller User Guide when the EAP is managed by the EAP Controller software. Convention Unless otherwise noted, the EAP or the device mentioned in this guide stands for 300Mbps Wireless N Access Point EAP110, Wireless N Gigabit Access Point EAP120 and EAP220.
CONTENTS Chapter 1 Introduction ...................................................................................................................................... 3 1.1 Overview of the EAP ........................................................................................................................... 3 1.2 Hardware Overview ............................................................................................................................ 3 1.2.1 LED ............................
5.6.4 Chapter 6 6.1 Download/Backup Trusted AP List.................................................................................... 37 Monitoring ...................................................................................................................................... 39 AP ............................................................................................................................................................ 39 6.1.1 6.2 AP List .......................................
Chapter 1 Introduction 1.1 Overview of the EAP EAP series products provide wireless coverage solutions for small-medium business. They can either work independently as standalone APs or be centrally managed by the EAP Controller software, providing a flexible, richly-functional but easily-configured enterprise-grade wireless network for small and medium business.
Figure 1-1 Top View of the EAP LED Status Indication Solid green The device is working properly. Flashing red System errors. RAM, flash, Ethernet, WLAN or firmware may be malfunctioning. Flashing yellow Firmware update is in progress. Do not disconnect or power off the device. Double-flashing red, green, yellow The device is being reset to its factory default settings. 1.2.
EAP120/EAP220: Figure 1-3 Interface Panel of EAP120/EAP220 Please note that EAP110 does not have the CONSOLE port, POWER port and ON/OFF button. The interface panel components of the EAP, from left to right, are described in the following list. Kensington Security Slot: Secure the lock (not provided) into the security slot to prevent the device from being stolen.
Passive PoE Adapter: Power LED: The Power LED indicates the status of the electric current: green (0-0.8A), red (0.8A-1A). POE Port: This port is used to connect the ETHERNET port of the EAP110. LAN Port: This port is used to connect your LAN. 1.2.3 Mounting Bracket The following figure describes the structure of the mounting bracket.
Chapter 2 Network Topology A typical network topology for the EAP is shown below. Figure 2-1 Typical Topology To deploy an EAP in your local network, a DHCP server is required to assign IP addresses to the EAP and clients. Typically, a router acts as the DHCP server. Ensure the EAPs are in the same subnet with the Controller Host in which the EAP Controller is installed.
Chapter 3 Management Mode 300Mbps Wireless N Access Point EAP110 and Wireless N Gigabit Access Point EAP120/EAP220 can either work under the control of the EAP Controller software or work independently as a standalone access point. When user establishes a large-scale wireless network, the management of every single AP in the network is complex and complicated. With the EAP Controller software, you can centrally manage the mass APs simply in a web browser.
Chapter 4 Network On Network page you can configure the IP address of the standalone EAP. Figure 4-1 Network Page Dynamic/Static: By default, the EAP device obtains an IP address from a DHCP server (typically a router). Select Static to configure IP address manually. Fallback IP: If the EAP fails to get a dynamic IP address from a DHCP server within ten seconds, the fallback IP will work as the IP address of the device.
Chapter 5 Wireless Wireless page, consisting of Wireless Settings, Portal, MAC Filtering, Scheduler, QoS and Rogue AP Detection, is shown below.
5.1 Wireless Settings Following is the page of Wireless Settings.
5.1.1 Wireless Basic Settings Figure 5-3 Wireless Basic Settings 2.4GHz Wireless Radio: Check the box to enable 2.4GHz Wireless Radio. Wireless Mode: Select the protocol standard for the wireless network. Wireless network created by the EAP is able to operate in the 2.4GHz frequency The EAP supports 802.11b/g/n, 802.11b/g, and 802.11n standards. It is recommended to select 802.11b/g/n, in which way clients supporting 11b, 11g or 11n mode can access your wireless network.
If the maximum transmit power is set to be larger than local regulation allows, the maximum Tx power regulated will be applied in actual situation. NOTE: In most cases, it is unnecessary to select maximum transmit power. Selecting larger transmit power than needed may cause interference to neighborhood. Also it consumes more power and will reduce longevity of the device. Select a certain transmit power is enough to achieve the best performance. 5.1.
SSID Broadcast: Enable this function, AP will broadcast its SSID to hosts in the surrounding environment, as thus hosts can find the wireless network identified by this SSID. If SSID Broadcast is not enabled, hosts must enter the AP’s SSID manually to connect to this AP. Security Mode: Select the security mode of the wireless network. For the security of wireless network, you are suggested to encrypt your wireless network.
Open System: After you select Open System, clients can pass the authentication and associate with the wireless network without password. However, correct password is necessary for data transmission. Shared Key: After you select Shared Key, clients has to input password to pass the authentication, or it cannot associate with the wireless network or transmit data. Key Selected: You can configure four keys in advance and select one as the present valid key.
WPA-PSK: Pre-shared key of WPA. WPA2-PSK: Pre-shared key of WPA2. Encryption: Select the encryption type, including Auto, TKIP, and AES. The default setting is Auto, which can select TKIP (Temporal Key Integrity Protocol) or AES (Advanced Encryption Standard) automatically based on the wireless station's capability and request. AES is more secure than TKIP and TKIP is not supported in 802.11n mode. It is recommended to select AES as the encryption type.
Encryption: Select the encryption type, including Auto, TKIP, and AES. The default setting is Auto, which can select TKIP (Temporal Key Integrity Protocol) or AES (Advanced Encryption Standard) automatically based on the wireless station's capability and request. AES is more secure than TKIP and TKIP is not supported in 802.11n mode. It is recommended to select AES as the encryption type. Wireless Password: Configure the WPA-PSK/WPA2-PSK password with ASCII or Hexadecimal characters.
Fragmentation Threshold: 5.1.4 Specify the fragmentation threshold for packets. If the size of the packet is larger than the fragmentation threshold, the packet will be fragmented into several packets. Too low fragmentation threshold may result in poor wireless performance caused by the excessive packets. The recommended and default value is 2346 bytes. Load Balance By restricting the maximum number of clients accessing the EAPs, Load Balance helps to achieve rational use of network resources.
Following is the page of Portal. Figure 5-10 Portal Page NOTE: To apply Portal in a wireless network, please go to Wireless→Wireless Settings→SSIDs to enable Portal of a selected SSID. 5.2.1 Portal Configuration Three authentication types are available: No Authentication, Local Password and External RADIUS Server. 1. No Authentication：Users are required to finish only two steps: agree with the user protocol and click the Login button.
2. Local Password：Users are required to enter the preset user name and password, which are saved in the EAP. 3. External RADIUS Server：Users are required to enter the preset user name and password, which are saved in the database of the RADIUS server. The RADIUS server acts as the authentication server, which allows you to set different user name and password for different users. Refer to the following content to configure Portal based on actual network situations.
Redirect URL: Enter the URL that a newly authenticated client will be directed to. Portal Customization: Select Local Web Portal, the authentication login page will be provided by the built-in portal server. The page configured below will be presented to users as the login page. Words can be filled in Input Box 1 and Input Box 2. Enter up to 31 characters as the title of the authentication login page in Input Box 1, like “Guest Portal of TP-LINK”. Enter the terms presented to users in Input Box 2.
Local Password Figure 5-12 Portal Configuration_Local Password Authentication Type: Select Local Password. Username: Enter the user name for local authentication. Password: Enter the password for local authentication. Please refer to No Authentication to configure Authentication Timeout, Redirect, Redirect URL, and Portal Customization. External RADIUS Server External RADIUS Server provides two types of portal customization: Local Web Portal and External Web Portal.
1. Local Web Portal Figure 5-13 Portal Configuration_External RADIUS Server_Local Web Portal Authentication Type: Select External RADIUS Server. RADIUS Server IP: Enter the IP address of the RADIUS server. Port: Enter the port for authentication service. RADIUS Password: Enter the shared secret of RADIUS server to log in to the RADIUS server. Please refer to No Authentication to configure Authentication Timeout, Redirect, Redirect URL, and Portal Customization.
2. External Web Portal Figure 5-14 Portal Configuration_External RADIUS Server_External Web Portal Authentication Type: Select External RADIUS Server. RADIUS Server IP: Enter the IP address of the RADIUS server. Port: Enter the port for authentication service. RADIUS Password: Enter the shared secret of RADIUS server to log in to the RADIUS server. Portal Customization: Select External Web Portal.
Click to add a new authentication policy and configure its parameters. Figure 5-16 Configure Free Authentication Policy Policy Name: Enter a policy name. Source IP Range: Enter the source IP address and subnet mask of the clients who can enjoy the free authentication policy. Leaving the field empty means all IP addresses can access the specific resources. Destination IP Range: Enter the destination IP address and subnet mask for free authentication policy.
Figure 5-17 Add Free Authentication Policy Here is the explanation of Figure 5-17: The policy name is Policy 1. Clients with IP address range 192.168.2.0/24 are able to visit IP range 10.10.10.0/24. Policy 1 is enabled. Click to edit the policy. Click to delete the policy. 5.3 MAC Filtering MAC Filtering uses MAC addresses to determine whether one host can access the wireless network or not. Thereby it can effectively control the user access in the wireless network.
Station MAC Group Follow the steps below to add MAC groups. Step 1: Click , two tables will be shown. Figure 5-19 Station MAC Group Step 2: Click and fill in a name for the MAC group. Figure 5-20 Add a Group Step 3: Click and input the MAC address you want to organize into this group.
Click in Modify column to edit the MAC group name or MAC address. Click to delete the MAC group or group member. MAC Filtering Association Figure 5-22 MAC Filtering Association SSID Name: Displays the SSID of the wireless network. Band: Displays the frequency band the wireless network operates at. MAC Group Name: Select a MAC group from the drop-down list to allow or deny its members to access the wireless network. Action: Allow: Allow the access of the stations specified in the MAC group.
Figure 5-23 Scheduler Page Settings Scheduler: Check the box to enable Scheduler. Association Mode: Select Associated with SSID/AP, you can perform configurations on the SSIDs/AP. The display of Scheduler Association is based on your option here. Scheduler Profile Configuration Follow the steps below to add rules. Step 1: Click , two tables will be shown.
Step 2: Click and input a profile name for the rule. Figure 5-25 Add a Profile Step 3: Click and configure the recurring schedule for the rule.
Scheduler Association This zone will display different contents based on your selection of association mode in Settings. 1. Associated with SSID Figure 5-27 Scheduler Association_Associated with SSID SSID Name: Displays the SSID of the standalone AP. Band: Displays the frequency band which the wireless network operates at. Profile Name: Select a profile name from the drop-down list. Profile name is configured in Scheduler Profile Configuration.
5.5 QoS The EAP supports Quality of Service (QoS) to prioritize voice and video traffic over other traffic types. In normal use, the default values for the EAP device and station EDCA should not need to be changed. Changing these values affects the QoS provided. Figure 5-29 QoS Page Wi-Fi Multimedia (WMM): By default, WMM is enabled. After WMM is enabled, the device has the QoS function to guarantee the transmission of audio and video packets with high priority.
5.5.1 AP EDCA Parameters AP Enhanced Distributed Channel Access (EDCA) parameters affect traffic flowing from the EAP device to the client station. Figure 5-30 AP EDCA Parameters Queue: Displays the transmission queues: Data 0>Data 1>Data 2>Data 3. Arbitration InterFrame Space: A wait time for data frames. The wait time is measured in slots. Valid values for AIFS are from 1 to 15.
5.5.2 Station EDCA Parameters Station EDCA parameters affect traffic flowing from the client station to the EAP device. Figure 5-31 Station EDCA Parameters Queue： Displays the transmission queues: Data 0>Data 1>Data 2>Data 3. Arbitration InterFrame Space： A wait time for data frames. The wait time is measured in slots. Valid values for AIFS are 1 through 15. Minimum Contention Window： An input to the algorithm that determines the initial random backoff wait time (window) for retry of a transmission.
5.6 Rogue AP Detection A Rogue AP is an access point that has been installed on a secure network without explicit authorization from a system administrator. The EAP device can scan all channels to detect all APs in the vicinity of the network. If rogue APs are detected, they are shown on the Detected Rogue AP List. If an AP listed as a rogue is legitimate, you can add it to the Trusted AP List.
5.6.1 Settings Figure 5-33 Enable Rogue AP Detection Rogue AP Detection: Check the box to enable Rogue AP Detection, then click Save. 5.6.2 Detected Rogue AP List Information about the detected rogue APs is displayed in the list. By default, the status of the detected rogue AP is unknown. You can click Known in Action column to move the AP to the Trusted AP List. Figure 5-34 Detected Rogue AP List Click to scan rogue APs.
Beacon Interval: The beacon interval used by the rogue AP. Signal: The strength of the radio signal emitting from the rogue AP. Beacon frames are transmitted by an AP at regular intervals to announce the existence of the wireless network. The default behavior is to send a beacon frame once every 100 milliseconds (or 10 per second). 5.6.3 Trusted AP List Information about the trusted APs is displayed in the list.
Save Action: Select Download (PC to AP) to import a trusted AP list to the device. Select Backup (AP to PC) to copy the trusted AP list to your PC. Source File Name: Click Browse and choose the path of a saved trusted AP list or to save a trusted AP list. File Management: Select Replace to import the list and replace the contents of the Trusted AP List.
Chapter 6 Monitoring On Monitoring page, you can monitor the network running status and statistics based on AP, SSID and Client. 6.1 AP AP List on the Monitoring page displays the device name, its MAC address and the number of clients. Below the AP List the AP’s detailed information will be shown, including Device Information, Wireless Settings, LAN Information, Client, LAN Traffic and Radio Traffic. Figure 6-1 AP Monitoring 6.1.
Device Name: Displays the device name. MAC: Displays the MAC address of the EAP. Num of Clients: Displays the number of clients connected to the EAP. Device Information Figure 6-3 Device Information Device Name: Displays the device name. Device Model: Displays the model of the device. Firmware Version: Displays the firmware version of the device. If you want to upgrade the firmware, please refer to 8.5 Firmware Upgrade. System Time: Displays the system time of the device.
Wireless Settings Figure 6-4 Wireless Settings Region: Displays the region you’ve selected. Channel/Frequency: Displays the channel number and the operating frequency. If you want to change them, please refer to 5.1.1 Wireless Basic Settings. Channel Width: Displays the spectral width of the radio channel used by the device. If you want to change it, refer to 5.1.1 Wireless Basic Settings. IEEE802.11 Mode: Displays the radio standard used for operation of your device.
LAN Port: Displays the maximum transmission rate and duplex mode (half-duplex or full-duplex) of the port. Client Figure 6-6 Client MAC: Displays the MAC address of the client of the AP selected in AP List. SSID: Displays the SSID the client is connected to. SNR(dB): Signal to Noise Ratio, the power ratio between the received wireless signal strength and the environmental noise strength. The bigger the value of SNR, the better network performance the device provides.
Rx/Tx Packets: Displays the total amount of packets received/sent on the LAN port. Rx/Tx Bytes: Displays the total amount of data (in bytes) received/sent on the LAN port. Rx/Tx Dropped Packets: Displays the total amount of dropped packets received/sent on the LAN port. Rx/Tx Errors: Displays the total amount of error packets received/sent on the LAN port. Radio Traffic Click Radio Traffic and you can monitor the data transmission status of the wireless network.
6.2 SSID Figure 6-9 SSID Monitoring 6.2.1 SSID List In SSID List you can monitor the related parameters of the wireless network. Figure 6-10 SSID List SSID Name: Displays the SSID name. If you want to modify it, please refer to 5.1.2 SSIDs. VLAN ID: Displays the VLAN which the SSID belongs to. If you want to change the VLAN ID, please refer to 5.1.2 SSIDs. Num of Clients: Displays the number of clients connected to the SSID.
Isolation: Displays the enabling or disabling of SSID Isolation. If you want to modify it, please refer to 5.1.2 SSIDs. Down(Byte): Displays the throughput of the downstream data. Up(Byte): Displays the throughput of the upstream data. 6.3 Client From User List, you can monitor the status of all the clients connected to the EAP including those who are authenticated. Figure 6-11 Client Monitoring 6.3.1 User List Figure 6-12 User List MAC: Displays the MAC address of the client.
SNR(dB): Signal to Noise Ratio, the power ratio between the received wireless signal strength and the environmental noise strength. The bigger the value of SNR, the better network performance the device provides. CCQ(%): Displays the wireless Client Connection Quality (CCQ). CCQ refers to the ratio of current effective transmission bandwidth and the theoretically maximum available bandwidth. CCQ reflects the actual link condition.
Active Time: Displays the amount of time the authenticated client has been connected to the root AP. Action: Click Unauthorize to stop giving authorization to the clients connected to the wireless network.
Chapter 7 Management Management page is mainly used for device management and maintenance. 7.1 System Log System log records information about hardware, software as well as system issues and monitors system events. With the help of system log, you can get informed of system running status and detect the reasons for failure. Following is the page of System Log. Figure 7-1 System Log Page 7.1.1 Log List From Log List you can view detailed information about hardware, software, system issues and so on.
Figure 7-2 Log List 7.1.2 Log Settings You can choose the way to receive system logs in Log Settings zone, where these parameters can be configured: Enable Auto Mail, Enable Server and Enable Nvram. Figure 7-3 Log Settings Enable Auto Mail If Auto Mail is enabled, system logs will be sent to a mailbox. The following content will be shown. Figure 7-4 Enable Auto Mail From: Enter the sender’s email address. To: Enter the recipient’s email address, which will receive the system logs.
SMTP Server: Enter the IP address of the SMTP server. Enable Authentication: Generally users are required to log in to the SMTP server by entering user name and password. Time Mode: User Name: Enter the sender’s email address. Password: Enter the password of the sender’s email address. Confirm Password: Enter the password again for confirmation. System logs can be sent at specific time or time interval. Fixation Time: Set a fixed time, for example, 15:00.
Following is the page of Web Server. Figure 7-6 Web Server Page HTTPS: HTTPS (Hypertext Transfer Protocol Secure) is enabled by default. Secure Server Port: Designate a secure server port for web server in HTTPS mode. By default the port is 443. Server Port: Designate a server port for web server in HTTP mode. By default the port is 80. Session Timeout: Set the session timeout time. If you do nothing with the web management page within the timeout time, the system will log out automatically.
Following is the page of Management Access. Figure 7-7 Management Access Page MAC Authentication: Check the box to enable MAC Authentication. After MAC Authentication is enabled, only the PCs in MAC address list can log in the device’s web management page. By default this function is disabled. All PCs in LAN can log in and manage the device. MAC1~MAC4: Enter the MAC addresses of the PCs which are authorized to log in the device. 7.4 LED ON/OFF Following is the page of LED ON/OFF.
SSH (Secure Shell) is a security protocol established on application and transport layers. SSHencrypted-connection is similar to a telnet connection, but essentially the old telnet remote management method is not safe, because the password and data transmitted with plain-text can be easily intercepted. SSH can provide information security and powerful authentication when you login this device remotely through an insecure network environment.
Once the device has become an SNMP agent, it is able to receive and process request messages from SNMP manager. Following is the page of SNMP. Figure 7-10 SNMP Page SNMP Agent: Enable SNMP Agent and the SNMP Agent will collect the information of this device and respond to information requests from one or more management systems. SysContact: Enter the textual identification of the contact person for this managed node. SysName: Enter an administratively-assigned name for this managed node.
Set Source: Defines the IP address (for example, 10.10.10.1) or subnet for management systems that can serve as Set Community to read and write the SNMP information of this device. The format of subnet is “IP address/bit” (such as 10.10.10.0/24). The default is 0.0.0.0, which means all hosts can read and write the SNMP information of this device. NOTE: Defining community can allow management systems in the same community to communicate with the SNMP Agent.
Chapter 8 System System page is mainly used to configure some basic information like user account and time, and realize functions including reboot, reset, backup, restore and upgrade the device. 8.1 User Account You can change the username and password to protect your device from unauthorized login. We recommend that you change the default user password on the very first system setup. Figure 8-1 User Account Page 8.
Figure 8-2 Time Settings 8.2.1 Time Settings Figure 8-3 Time Settings Click the button and the device will obtain GMT time from NTP server. IP address of the NTP server has to be filled in. Click the button, your PC’s time will be obtained as the device’s system time. Time zone: Select your local time zone from the drop-down list. Date: Set the current date, in format MM/DD/YYYY. For example, for November 25, 2014, enter 11/25/2014 in the field. Time: Specify the device’s time.
Primary/Secondary NTP Server: If you’ve selected Get GMT from an NTP server, please input the primary NTP sever address and an alternative NTP server address. 8.2.2 Daylight Saving Figure 8-4 Daylight Saving Daylight Saving: Enable or disable the DST. DST is disabled by default. Mode: Options include Predefined Mode, Recurring Mode and Date Mode. Please refer to the following content for more information. Predefined Mode Figure 8-5 Predefined Mode Mode: Select Predefined Mode.
Recurring Mode Figure 8-6 Recurring Mode Mode: Select Recurring Mode. The configuration is recurring in use. Time Offset: Specify the time adding in minutes when Daylight Saving Time comes. Start/End: Select starting time and ending time of Daylight Saving Time. Date Mode Figure 8-7 Date Mode 8.3 Mode: Select Date Mode. Time Offset: Specify the time adding in minutes when Daylight Saving Time comes. Start/End: Select starting time and ending time of Daylight Saving Time.
8.4 Backup & Restore Figure 8-9 Backup & Restore You can save the current configuration of the EAP as a backup file and restore the configuration via a backup file. Back up the settings before you upgrade the device or upload a new configuration file can prevent it from being lost. Restore function helps you to restore the device to previous settings by uploading a backup file. 8.5 Firmware Upgrade Figure 8-10 Firmware Upgrade Please log in http://www.tp-link.
NOTE: 1. Please select the proper software version that matches your hardware to upgrade. 2. To avoid damage, please do not turn off the device while upgrading. 3. After upgrading, the device will reboot automatically.
Appendix A: Specifications HARDWARE FEATURES Model EAP110 Interface Kensington lock slot RESET button EAP120 EAP220 ETHERNET: 10/100Mbps Ethernet port (RJ45) ETHERNET: 10/100/1000Mbps Ethernet port (RJ45) CONSOLE port (RJ-45) Power connector (DC-2) Power Supply 24V/1A passive PoE adapter (included) PoE(802.3af-compliant, 36-57VDC, 0.2A Max) or external 12VDC/1A power supply PoE (802.3af-compliant, 36-57VDC, 0.4A Max)or external 12VDC/1.5A power supply Maximum Power Consumption 7.7W 4.4W 9.
