910011262 REV 1.0.
Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright ©2015 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.
responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. surface. The device complies with RF specifications when the device used at 20 cm from your body. 2. SRD with DSSS and other than FHSS wideband modulation 1.3.Maximum applications. 100 mW e.i.r.p. Indoor 2.1. Maximum mean e.i.r.p. density is 2 mW/MHz. Maximum 100 mW e.i.r.p. 2.2. Maximum mean e.i.r.p. density is 20 mW/MHz. Maximum 100 mW e.i.
This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : l'appareil nedoit pas produire de brouillage, et 5850 MHz shall be such that the equipment still complies with the e.i.r.p.
with minimum distance 32cm between the radiator & your body. 減少電磁波影響，請妥適使用。 安全諮詢及注意事項 Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 32 cm de distance entre la source de rayonnement et votre corps.
● ● ● ● ● ● When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations.
TP-LINK TECHNOLOGIES CO., LTD The product carries the CE Mark: For the following equipment: Product Description: AC1900 Wi-Fi Range Extender Person responsible for marking this declaration: Model No.
Contents Introduction........................................................................1 Product Overview ..................................................................... 1 What can your Extender do .................................................. 1 Support for the 802.11ac wireless technology ..................... 1 Main Features....................................................................... 2 Appearance ..............................................................................
The RE580D AC1900 Wi-Fi Range Extender is dedicated to Small Office/Home Office (SOHO) wireless network solutions. It will enlarge your existing wireless network and mobility within your wireless network while also allowing you to connect a wired device to a wireless environment. Increased mobility and the absence of cabling will be beneficial for your network. The extender provides two options to finish the quick setup.
Complies with IEEE 802.
Name Status Indication Solid blue The extender has established a secure connection, and the signal strength is adequate. (RE) Solid orange Blinking (5GHz)/ (2.4GHz) (Power) (Ethernet) The extender has established a secure connection, but the signal strength is too weak. No active connection. On The extender is connected to the 2.4GHz or 5GHz wireless network of your host network. Off No connection. On The extender is on.
Please read this guide carefully before installing and using the device. The operating distance range of your wireless connection can vary significantly depending on the physical position of the wireless devices. Factors that can weaken signals by getting in the way of your network’s radio waves are metal appliances or obstructions, and walls. Typical ranges vary based on the types of materials and background RF (radio frequency) noise in your home or office.
Your router should support WPS. Otherwise, please use Using your web browser. Place your extender in a well-ventilated place far from direct sunlight, any heater or heating vent. Leave at least 2 inches (5cm) space around the device for heat dissipation. Turn off your extender and unplug the power adapter in a lighting storm to avoid damage. Use Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0 or above.
Some ISP gateways disable the WPS function by default, if the WPS method fails, please refer to Using your Web Browser. If you are connecting the extender to a dual-band router but only 2.4GHz ( ) or 5GHz ( ) LED is on, repeat step 1) and 2) again to connect the other band. For more information about using WPS on your router, please refer to the router manufacturer's user guide. Immediately press the RE button on your extender.
Power On Plug the extender into an electrical outlet near your router, and wait until the Power LED is lit and solid blue. ● Connecting via Wireless Disconnect the Ethernet (wired) connection to your computer. Click the Wi-Fi icon on the taskbar and connect to the extender's network (e.g. TPLINK_Extender_2.4GHz or _5GHz). Connect to the Extender ● Connecting via Ethernet Cable Disable the Wi-Fi on your computer. Connect the extender to your computer via an Ethernet cable.
Configure Create a new username and password to log in the web management page, then click Confirm. Select your router's 2.4GHz host network and enter the password, then click Next. Select your router's 5GHz host network and enter the password, then click Next.
Verify your wireless settings and click Finish. The corresponding LEDs (2.4GHz and 5GHz) should turn on and stay solid. If your router does not support 5GHz wireless network, please click Skip to continue. Either keep the same SSIDs as your host network or create new names for the extended networks, then click Next.
Enjoy! Both extended networks share the same Wi-Fi password as your main network, but may have different wireless network names if you customize the SSIDs during the configuration. Relocate Plug the extender into an electrical outlet about halfway between your router (Host Network) and the Wi-Fi dead zone. Wait until the LED is lit with a solid blue. If not, relocate the extender closer to the router to achieve a good (or better) signal quality.
Launch a web browser and type in http://tplinkrepeater.net, then go to Settings > Status webpage. You can view the network connection in the Status webpage. ● The normal status. ● The extender is failed to connect to the wireless network of your router.
Instructions for the icons of 2.4GHz/5GHz wireless status: Name Instructions The wireless is on and encrypted. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings > Status webpage. Click the icons of your router, the extender and clients. The detailed instructions for the corresponding icon are displayed below. The wireless is on and unencrypted. Router：The wireless is off, or the connection is failed. / Extender：The wireless is off. / The icons are selected.
If you want to extend another network, you can refer to the following steps to finish it quickly. Launch a web browser and type in http://tplinkrepeater.net，then go to Settings->Wireless->Connect to Network webpage. Enable Connect to 2.4GHz/5GHz Network. Then click Wireless Scanner to scan the network you want to extend.
Select the network you want to extend from the list. Once a network is selected, the SSID and security settings of that network will automatically fill in. If the host network is encrypted, enter the password in the box of the host wireless security. If the network you want to extend is on but not shown in the list, please try by following the steps below. Move the extender closer to your router. Then click Refresh on the top-right corner of the list to scan the network again.
Relocate. Plug in the extender halfway between your wireless router (Host Network) and the Wi-Fi dead zone. Wait for the extender to reconnect and the LED turns solid blue. If not, relocate it closer to the router to achieve a good (or better) signal quality. Enjoy! The extender shares the same wireless network name (SSID) and wireless password as your host network. If you want to change the wireless network name (SSID), please refer to Extended Settings.
Manage the Extender’s Wi-Fi Security Settings Change your Admin Account Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->System Tools->Admin Account webpage. Create a new username and password as shown in the figure below. Click Save to save the settings. Control the Wireless Devices Access to the Extender The Access Control function controls the devices connected to the extender by the wireless connection.
Add the device to the blacklist by following the ways. ● Add the Online Devices to the blacklist. In the Online Devices list, you can view the information about the devices connected to the extender. For one device, you can click the icon to add the device to the blacklist. For several devices, select them and click Block to add them at the same time. Device Name: Enter the device name. MAC Address: Enter the MAC address of the host in XX-XX-XX-XXXX-XX format (e.g. 00-11-22-33-44-AA).
Click OK to save your settings. Modify or Remove a Device in the Blacklist/Whitelist Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Wireless-> Access Control webpage. Click the Add button. You can modify or remove the devices in the Blacklist or Whitelist. ● Modify a Device in the Blacklist or Whitelist. Click the icon , and then enter the device name and MAC address. Click OK to save the setings. ● Device Name: Enter the device name.
Change the Extender’s IP Address By default, the extender is set to obtain an IP address automatically from the front router. If you want to use a specific IP address appropriate to your network demand, please refer to the steps below. We do NOT recommend you change the IP address unless you are quite sure about the IP setting for special network demand, random changes may lead to Internet disconnection. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Network webpage.
When the DHCP Server is On, please make sure that IP Address Pool, Default Gateway for the DHCP server and LAN IP address are in the same segmengt as the router. Otherwises, the extender cannot access the Internet. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings->Network webpage. If the DHCP Server is On, please configure it as shown in the figure bleow. Primary DNS (Optional): Enter the DNS IP address provided by your ISP.
Client Name: The name of the DHCP client. MAC Address: The MAC address of the DHCP client. Assigned IP Address: The IP address that is allocated to the client by the DHCP server. Lease Time: The time duration that the IP address is leased to the DHCP client. Click Refresh to refresh the DHCP Client List.
The extender RE580D can be used as a wireless adapter to connect any Ethernet-enabled device, such as a Blu-ray player, game console, DVR, or smart TV, to your wireless network. After the extender connected to the Internet, you can connect an Ethernetenabled device to the extender using an Ethernet cable. This chapter covers the following topics: Entertainment Adapter By default, the Ethernet ports connect to the 5GHz wireless network. If you want the extender to connect to the 2.
LED Control can turn off the LEDs at the specific time. The extender can still work normally after the LEDs are off. Launch a web browser and type in http://tplinkrepeater.net, then go to Settings-> System Tools -> Time Settings webpage. Select the Time Zone of your location. Click Save to save your settings.
● LED Off Time: Set the time to turn off the LEDs. Please DO NOT power off the extender during the upgrade process. Click Save to save your settings. Launch a web browser and type in http://tplinkrepeater.net，then go to Settings->System Tools->Firmware Upgrade webpage. You can view the firmware version and the software version. Search the latest firmware of your extender from the Support page at www.tplink.com. Then download the latest firmware upgrade file to your computer.
Please DO NOT power off the extender during the backup process. ● Configuration Restore Click Browse to locate and select your backup file. Click Restore and then YES to restore the extender. The restore process may take a few minutes to complete and the extender will automatically reboot itself when finished. Please DO NOT power off the extender during the restore process. Factory Restore will erase all settings that you have configured for the extender.
Launch a web browser and type in http://tplinkrepeater.net. Click Reboot on the top right corner to reboot the extender. Launch a web browser and type in http://tplinkrepeater.net. You can also click the following buttons to apply the settings. Click Refresh to update the system log. Click Delete All to permanently remove all logs. Click Logout on the top right corner to log out the management webpage safely. Click Save Log to save the system log as a .txt file on your computer.
Name Status Common Default Settings This chapter covers the following topics: Username admin Password admin IP Address 192.168.0.254 Subnet Mask 255.255.255.0 http://tplinkrepeater.net Factory Defaults Domain Troubleshooting Wireless Specifications Glossary SSID 2.4GHz: TP-LINK_Extender_2.
browser, enter the default domain http://tplinkrepeater.net in the address field and get logged in. If you are unable to log in, please RESET the device, and then use the default IP address to get into the web-based configuration page, reconfigure the device. T1.
Security Physical and Environment General Standards and Protocols IEEE 802.3, IEEE 802.3u, IEEE 802.11a, IEEE 802.11n, IEEE 802.11b, IEEE 802.11g, IEEE 802.1x, IEEE 802.11e, IEEE 802.11i, IEEE 802.11ac, TCP/IP, DHCP Safety & Emission CE Ports One 10/100/1000M Auto-Negotiation LAN RJ45 port Antennas Omni Directional antenna with 1.59dBi gain(2.4G) and 1.03dBi gain(5GB1)1.
interoperability of next-generation wireless local area networking (WLAN) products. ● ● ● ● ● ● ● ● ● ● Access Point (Range Extender) - A wireless LAN transceiver or "base station" that can connect a wired LAN to one or many wireless devices. Access points can also bridge to each other. DNS (Domain Name System) – An Internet Service that translates the names of websites into IP addresses. Domain Name - A descriptive name for an address or group of addresses on the Internet.
