TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router Rev: 1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark Bulgaria None General authorization required for outdoor use and public service Italy None If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum)
Industry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N VoIP ADSL2+ Modem Router Model No.
CONTENTS Package Contents ....................................................................................................1 Chapter 1. Product Overview...................................................................................2 1.1 Overview of the Modem Router ...................................................................................... 2 1.2 Main Features................................................................................................................. 3 1.
4.6 Wireless ........................................................................................................................ 43 4.6.1 Basic Settings .................................................................................................................... 43 4.6.2 WPS Settings ..................................................................................................................... 45 4.6.3 Wireless Security .....................................................................
4.12.3 WAN Host ......................................................................................................................... 86 4.12.4 Schedule........................................................................................................................... 88 4.13 Traffic Control ............................................................................................................... 89 4.13.1 Control Settings ....................................................................
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package: One TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router One Power Adapter for TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router Quick Installation Guide One RJ45 cable Three RJ11 cables One ADSL splitter One Resource CD for TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router, including: This User Guide Other Helpful Information
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 1. Product Overview Thank you for choosing the TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router. 1.1 Overview of the Modem Router The TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.2 Main Features Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), four RJ11 ports, two USB 2.0 ports Provides external splitter. Adopts Advanced DMT modulation and demodulation technology. Supports bridge mode and Router function. Multi-user sharing a high-speed Internet connection. Downstream data rates up to 24Mbps, upstream data rates up to 3.5Mbps (With Annex M enabled).
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The Router’s LEDs are located on the front panel (View from left to right). They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Status On The modem router is powered on. Off The modem router is off. Please ensure that the power adapter is connected correctly. On ADSL line is synchronized and ready to use.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide On （Line） （Phone1-2） (WPS) Flash A valid PSTN connection. Incoming calls and outgoing calls are transmitted trough PSTN line. Off PSTN connection fails. On The phone is off hook. Flash The phone is ringing. Off The phone is on hook. On A wireless device has been successfully added to the network by WPS function. Slow Flash WPS handshaking is in process and will continue for about 2 minutes.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.3.2 The Back Panel The Router's ports, where the cables are connected, and RESET button are located on the front. Figure 1-2 POWER: The Power plug is where you will connect the power adapter. USB1/USB2: The USB port connects to a USB storage device or a USB printer. PHONE2/PHONE1:The phone port connects to a phone set.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 1-3 WPS: The switch for the WPS function. For details, please refer to 4.6.2 WPS Settings. WiFi: The switch for the WiFi function. ON/OFF: The switch for the power.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 2. Connecting the Modem Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet). PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. TCP/IP protocol on each PC. Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 2.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 5: Power on the computers and LAN devices. Step 6: Attach the power adapter. Connect the power adapter to the power connector on the rear of the device and plug in the adapter to an electrical outlet or power extension. The electrical outlet shall be installed near the device and shall be easily accessible.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide 3.1 Configuring the PC After you directly connect your PC to the Modem Router or connect your adapter to a Hub/Switch which has connected to the Modem Router, you need to configure your PC’s IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1).
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above. Now, you can run the Ping command in the command prompt to verify the network connection.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Modem Router. Figure 3-6 You can check it following the steps below: 1) Is the connection between your PC and the Modem Router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Router's IP address is 192.168.1.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-8 Note: 1) Do not mix up the user name and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy. Go to Tools menu→Network→LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 2.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-9 3. Change the VPI or VCI values which are used to define a unique path for your connection. If you have been given specific settings for this to configuration, type in the correct values assigned by your ISP. Click Next.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-10 4. Here we select PPPoE WAN Link Type for example, enter the Username, Password and Confirm Password given by your ISP, and then click Next. Figure 3-11 5. On the Wireless screen, we use the default SSID, select Region and Mode. Set a Password or select Disable Security(Disable Security is not recommended.), and then click Next to continue.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 6. Basic parameters of Voice can be set on the Voice screen. Please enter a profile name to identify this account and other parameters provided by your ISP. If you don’t want to configure VoIP function now, leave "Profile Name" blank and click Next to skip. Figure 3-13 7. On this page, please confirm all parameters. Click Previous to modify or click the Save button to make the configuration take effect. Figure 3-14 8.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-15 18
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 4. Configuring the Modem Router This chapter will show each Web page's key function and the configuration way. 4.1 Login After your successful login, you will see the fifteen main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below. 4.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-1 4.3 Quick Setup Please refer to Section 3.2 Quick Installation Guide. 4.4 Network Choose “Network”, there are many submenus under the main menu. Click any one of them, and you will be able to configure the corresponding function.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.4.1 WAN Settings Choose “Network”“WAN Settings”, and you will see the WAN Port Information Table in the screen similar to Figure 4-2, which describes the WAN port settings and the relevant manipulation to each interface. There are five different configurations for the connection types, which are Static IP, Dynamic IP, PPPoE, IPoA, and Bridge. You can select the corresponding types according to your needs.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-3 4.4.1.1 Static IP Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-4 ATM Configuration: VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. VCI (1~65535): Identifies the virtual channel endpoints in an ATM network. The valid range is from 1 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value provided by your ISP.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide DNS Server/ Secondary DNS Server: Here you can set DNS Server (at least one) manually. The Route will use this DNS Server for priority. Default Gateway: select a WAN Interface from the drop-down list as the IPv4 default gateway. MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-5 Click Advanced, advanced selections for WAN Service Setup can be shown. MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP. Enable NAT: This technology translates the IP addresses of a local area network to a different IP address for the Internet.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Primary DNS Server/ Secondary DNS Server: Choose “Set DNS Server manually”, you can set DNS Server (at least one) manually here. The Route will use this DNS Server for priority. Click the Save button to save the settings. 4.4.1.3 PPPoE If your ISP provides a PPPoE connection and you need to use an ATM Interface, choose PPPoE in the drop-down list, and then the screen will be displayed as below.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Authentication Method: Select the Authentication Method from the drop-down list, the default method is AUTO_AUTH, and you can leave it as a default setting. Choose the right connection type according to your needs: For PPPoE connection, you can select Connect on demand or Connect automatically or Connect manually. Connect on demand is dependent on the traffic.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-7 4.4.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the WAN service type on the screen.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-8 IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. If you forget, you can ask your ISP. DNS Server/Secondary DNS Server: Type in your preferred DNS server. Default Gateway: select a WAN Interface from the drop-down list as the IPv4 default gateway. 4.4.1.6 Bridge If you select this type of connection, the modem can be configured to act as a bridging device between your LAN and your ISP.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-9 Note: After you finish the Internet configuration, please click Save to make the settings take effect. 4.4.2 EWAN Choose “Network”“EWAN”, and you will see the Ethernet WAN Interface screen similar to Figure 4-10. There are there different configurations for the connection types, which are Dynamic IP, Static IP and PPPoE. You can select the corresponding types according to your needs.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-10 4.4.2.1 Dynamic IP Select this option, the Modem Router will be able to obtain IP network information dynamically from a DHCP server provided by your ISP (as shown Figure 4-10). The next configuration is similar to Dynamic IP over ATM interface (see section 4.4.1.2 Dynamic IP) 4.4.2.2 Static IP Select this option if your ISP provides static IP information to you and you want to use an Ethernet Interface.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-11 4.4.2.3 PPPoE If your ISP provides a PPPoE connection and you need to use an Ethernet Interface, select PPPoE option for the WAN service type on the screen. The following configuration is similar to PPPoE over ATM interface (see section 4.4.1.3 PPPoE).
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-12 4.4.3 Interface Grouping Choose “Network”“Interface Grouping”, you can view all the current groups on this page (shown in Figure 4-13).
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide VLAN: Enable or disable this function. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same LAN, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-15 IP Address: You can configure the Modem Router’s IP Address and Subnet Mask for LAN Interface. IP Address: Enter the Modem Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1. Subnet Mask: Enter the Modem Router’s Subnet Mask, the default value is 255.255.255.0.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Leased Time: The Leased Time is the amount of time in which a network user will be allowed connection to the Modem Router with their current dynamic IP address. Enter the amount of time, in hours, then the user will be “leased” this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 1440 minutes.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-17 Virtual Private Network (VPN) - VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pass through the Modem Router. PPTP Passthrough - Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow PPTP tunnels to pass through the Modem Router, click Enable.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-18 DSL Modulation Type: Select the DSL operation Modulation Type which your DSL connection uses. Annex Type: Select the DSL operation Annex Type which your DSL connection uses. Click the Save button to save your settings. 4.5 DHCP Server Choose “DHCP Server”, you can see the next submenus: Click any of them, and you will be able to configure the corresponding function. 4.5.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-19 Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Modem Router is 192.168.1.1, the default Start IP Address is 192.168.1.100, and the Start IP Address must be 192.168.1.100 or greater, but smaller than 192.168.1.254. End IP Address: Enter a value for the DHCP server to end with when issuing IP addresses.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note: 1) 2) 3) To use the DHCP server function of the Modem Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". You have to disable NAT of the WAN connections, or the DHCP Relay may not take effect. If you select Disabled, the DHCP function will not take effect. Click the Save button to save your settings. 4.5.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-21 MAC Address: The MAC address of the PC for which you want to reserve an IP address. IP Address: The IP address reserved for the PC by the Modem Router. Status: The status of this entry either Enabled or Disabled. To Reserve an IP address: 1. Click the Add New button. Then Figure 4-22 will pop up. 2. Enter the MAC address (in XX:XX:XX:XX:XX:XX format.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-23 To add a vendor class: 1. Click the Add New button. Then Figure 4-24 will pop up. 2. Enter parameters for the vendor class. Click the Save button. Figure 4-24 To modify or delete an existing entry: 4. Click the Edit in the entry you want to modify. If you want to delete the entry, click the Delete. 5. Modify the information. 6. Click the Save button.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.6 Wireless Choose “Wireless”, there are six submenus to configure Wireless LAN settings. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.6.1 Basic Settings Choose “Wireless””Basic”, you will see the screen of Wireless--Basic settings shown as below. The basic settings for wireless networking are set on this screen.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 11bg mixed: Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed: Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can be connected to the Modem Router. When 802.11n mode is selected, only 802.11n wireless stations can connect to the Modem Router.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide WEP Index: This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It indicates the index of the WEP key. Auth Type: This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It indicates the authorization type of the Root AP. Password: If the AP your Modem Router is going to connect needs password, you need to fill the password in this blank. Click Save to save your settings. 4.6.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide You can also keep the default WPS Status as Enabled and click the Add device button in Figure 4-26, then Choose “Press the button of the new device in two minutes” and click Connect. (Shown in the following figure) Figure 4-27 Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then click Connect button. Step 3: “Connect successfully” will appear on the screen of Figure 4-28, which means the client device has successfully connected to the Modem Router. III. Enter the Modem Router’s PIN on your client device Use this method if your client device asks for the Modem Router’s PIN number.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-29 Disable Wireless Security: If you do not want to use wireless security, check this radio button. But it’s strongly recommended to choose one of the following modes to enable security. WEP: It is based on the IEEE 802.11 standard. If you check this radio button, you will find a notice in red as show in Figure 4-29. Figure 4-30 Auth Type - you can choose the type for the WEP security on the drop-down list.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide WEP Key - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Description: A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New button. The following page will appear, shown in Figure 4-32: Figure 4-32 To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX:XX:XX:XX:XX:XX (X is any hexadecimal digit).
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 5) Click the Back button. The filtering rules that configured should be similar to the following list: 4.6.5 Wireless Advanced Choose menu “Wireless””Wireless Advanced”, you can configure the advanced settings of your wireless network. Figure 4-33 Transmit Power: Here you can specify the transmit power of Modem Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. Enable Short GI: This function is recommended for it will increase the data capacity by reducing the guard interval time. Enabled Client isolation: This function can isolate wireless stations on your network from each other.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.7.1 SIP Account Choose “Voice”“SIP Account”, you will see the screen similar to Figure 4-35. SIP accounts are necessary for making VoIP calls. This section introduces how to setup the SIP(Session Initiation Protocol) account for your Modem Router. Figure 4-35 Profile Name: Displays the profile name of the account. Registrar Address: Displays the IP address or domin name of the SIP Registrar server.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-36 SIP Account Basic Profile Name: Assign a name to identify the profile. Please note that special characters are not allowed. Phone Number: Enter the phone number of the account you applied. Display Name: Assign a name for your account. This name is the Caller-ID you want to be displayed on your friend’s display panel, which can let your friend easily know who is calling.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Preferred Receive Ptime: Ptime, short for packet time, refers to the time interval for a voice packet to be sent by the remote caller. The unit is ms (millisecond). Usually the default value 20ms is OK. Priority: Select a priority for this account. This priority is useful when more than one account is added in this Modem Router. Incoming Call Route: Select which line the incoming VoIP call will be routed to.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-37 Prefix: Displays the prefix of your plan. This prefix refers to the initial digit(s) of the numbers you dial. Op: Displays the operation of this plan. Destination: Displays the account or network used for this plan. Enable: Displays the interface(s) enabled in this plan. Remove: Check the box and then click the Remove button below so that the very plan will be deleted.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide If “TimeOut” is selected, the dialing will be sent out when timeout starts. The timeout activates when no more digits are dialed in a specific duration; If “#” is selected, the dialing will not be sent until “#” is dialed; If “#/TimeOut” is selected, the dialing will be sent out when timeout starts or “#” is dialed; If “None” is selected, the dialing will not be sent out unless the length of number you dial meets the Max Length.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-40 Prefix: Set number(s) as the prefix. Up to 16 characters can be entered. Interface Barring: You can check any box to disable interface(s). Numbers matching prefix in Forbidden Call list are not allowed to be dialed out through the selected interface(s). For example, if you set a dial plan list in the screen as shown in Figure 4-40, phone numbers starts with ‘020’ can only be dialed out through PSTN line. 4.7.2.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-42 Phone Enable: Check the box behind to enable the function. Dial Settings Dial Plan Priority: The parameters configured here determine which network or SIP account to use when making outgoing calls. In the 1st field, there are options of networks. Please note if no SIP account is set on SIP Account page, only PSTN network will be available. Otherwise networks available are VOIP, PSTN Preferred and PSTN.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide PSTN Preferred & Account X (a certain account) – The Router will select the network to make calls according to your dial plans set on Dial Plan page. If VoIP network is selected, the account used will be Account X. But if no dial plan is matched with your outgoing call, then PSTN network will be automatically selected. PSTN – The Modem Router will always use PSTN network disregarding your dial plans on Dial Plan page.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide through selected account when "No answer" time is out. Please note that network or account available here varies with that in Dial Plan Priority field. Telephony Settings VAD Support: VAD(Voice Activation Detection) prevents transmitting the silence packets to consume the bandwidth. It is also known as Silence Suppression which is a software application that ensures the bandwidth is reserved only when voice activity is activated.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide DSCP for SIP/RTP: DSCP(Differentiated Services Code Point) is the first 6 bits in the ToS byte. DSCP marking allows users to assign specific application traffic to be executed in priority by the next Router based on the DSCP value. Select DSCP for the SIP(Session Initiation Protocol) and RTP(Real-time Transport Protocol) respectively. If you are unsure, please always keep the default value.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.7.5 Speed Dial Choose “Voice”“Speed Dial”, you will see the screen as shown in Figure 4-44. This section introduces how to configure Speed Dial for your account. Speed Dial function can help to store frequently used telephone numbers and make your dial more convenient. It allows you to make a call by pressing a short number and the pound sigh # on the phone keypad instead of the original number.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-47 Call Log: Check the Enable if you want to make this function take effect; otherwise check the Disable. Start: Beginning time of the call. Source: Caller ID, either phone number or IP address. Dest: Callee ID, either phone number or IP address. Type: Call types, including Incoming (VoIP), Incoming (PSTN), Outgoing (VoIP) and Outgoing (PSTN).
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Call Firewall can be used to control incoming calls. This section introduces how to configure the Call Firewall. Choose “Voice”“Call Firewall““Mode Setting“, you will see the screen as shown in Figure 4-49. Figure 4-49 Call Firewall Enable: Check the box if you want to make the Call Firewall take effect. Black: Check the Black box to enable Black List mode. Calls from numbers placed in the Black List will be denied.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-51 Enter a number with the length in the range of [3, 16]in the field of Black List Number and Click the Save button to make the configuration take effect, then you will go back to the previous page and see the following list as shown in Figure 4-50. If you want to delete the entry, check the Remove box first and then click the Remove button.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide in Black List and 2224 in White List, with Black List mode enabled, incoming call number 2224510 will be allowed. 4.7.8 USB Voice Mail Choose “Voice”“USB Voice Mail“, you will see the screen as shown in Figure 4-54. USB Voice mail is used to record voice messages when the call is not answered.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-55 Enable Local Play Operation Notify: Check this box so there will be sound indication for operation when you listen to the voice messages. This is enabled by default. If you are very familiar with the operations, you can disable it. Enable Global Wav Format: Check this box and all the voice message will be saved as wav files in your USB device. It is convenient for users to listen to the voice messages on the computer.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 3) Input the PIN code according to the notification. 4) You can listen to all the new messages after the PIN code is validated. Click Save to save your configurations. Click Back to go back to the previous page, i.e. Figure 4-54. 4.8 USB Settings There are six submenus under the USB Settings menu, USB Mass Storage, User Accounts, Storage Sharing, FTP Server, Media Server and Print Server.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Capacity: The storage capacity of the USB driver. Status: Indicates the shared or non-shared status of the volume. Active means volume can be shared, while Inactive means volume can not be shared. If Deactivate in Action field is enabled, Inactive will be displayed in the Status field, which means volume can not be shared.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4. Re-enter the password in the Confirm Password field. 5. Click the Set button, and then a new entry will be added in the table. 6. Click the Apply button to apply your settings. Click the Refresh button to refresh this page immediately. 4.8.3 Storage Sharing Choose menu “USB Settings” → “Storage Sharing”, you can configure a USB disk drive attached to the Modem Router and view volume and share properties on this page as shown below.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-59 2. 3. 4. Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries. Note: 1.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-60 Server Status: Indicates the FTP Server's current status. Internet Access: Enable or disable this function. Internet Address: If Internet Access is enabled, WAN IP will be displayed here. Service Port: Enter the FTP Port number to use. The default is 21. Share Name: This folder's display name. Directory: The real full path of the specified folder. User Index: The authorization of the user is displayed.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-61 2. 3. 4. Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder. Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries. Note: 1.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Server Enable: Select this box to enable this function. Server Name: The name of this Media Server. To add a new share folder for your media server, please follow the instructions below: a) Click Add New Folder button, and you will see the screen as shown in Figure 4-77. b) Enter the name of the share folder in Share Name field. c) Click the Apply button to apply the configuration.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.9 Route Settings Choose “Route Settings”, it includes three menus: Default Gateway, Static Route and RIP Settings. The detailed descriptions are provided below. 4.9.1 Default Gateway Choose “Route Settings”“Default Gateway”, you can see the Default Gateway screen. You can select a WAN Interface from the drop-down list as the system default gateway. Figure 4-65 Click the Add Interface button, you can add WAN Interfaces.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-67 2. Enter the following data: Destination IP Address: The Destination IP Address is the address of the network or host that you want to assign to a static route. Subnet Mask: The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note: RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE). 4.10 Forwarding There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. 4.10.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 2. Select the service you want to use from the Common Service Port list. If the Common Service Port menu does not list the service that you want to use, enter the number of the service port or service port range in the Service Port field. 3. Select the service you want to use from the Use Interface list. 4. Enter the IP address of the computer running the service application in the IP Address field. 5.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-71 To add a new rule, follow the steps below. 1. Click the Add New button, the next screen will pop-up as shown in Figure 4-72. 2. Select a common application from the Common Service Port drop-down list, then the Trigger Port field and the Open Ports field will be automatically filled. If the Common Service Port do not have the application you need, enter the Trigger Port and the Open Ports manually. 3.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Open Protocol: The protocol used for Incoming Port, either TCP, UDP, or ALL (all protocols supported by the Modem Router). Status: The status of this entry, Enabled means the Port Triggering entry is enabled. Modify: To modify or delete an existing entry. Common Service Port: Some popular applications already listed in the drop-down list of Open Protocol. To modify or delete an existing entry: 1.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-73 To assign a computer or server to be a DMZ server: 1. Click the Enable button. 2. Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field. 3. Click the Save button. 4.10.4 UPnP Choose menu “Forwarding→UPnP”, and then you can view the information about UPnP in the screen (shown in Figure 4-74).
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click the Disable button to disable UPnP. Click the Refresh button to update the Current UPnP Settings List. 4.11 Parental Control Choose menu “Parental Control”, and you can configure the parental control in the screen as shown in Figure 4-75. The Parental Control function can be used to control the internet activities of the child, limit the child to access certain websites and restrict the time of surfing.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide MAC Address of Current PC: This field displays the MAC address of the PC that is managing this Modem Router. If the MAC Address of your adapter is registered, you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above. Add URL: Here you can input the net addresses which the child is allowed to access. Click the Save button to save your settings. 4.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Add New: Click the Add New button to add a new rule entry. Enable Selected: Click the Enable Selected button to enable the selected rules in the list. Disable Selected: Click the Disable Selected button to disable the selected rules in the list. Delete Selected: Click the Delete Selected button to delete the selected entries in the table. The methods to add a new rule: 1.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Description: Here displays the description of the host and this description is unique. Address Info: Here displays the information about the host. It can be IP or MAC. Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button. 2. In the Mode field, select IP Address or MAC Address.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-80 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In IP Address field, enter the IP address. If you select MAC Address, the screen shown is Figure 4-81. Figure 4-81 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In MAC Address field, enter the MAC address. If you select URL Address, the screen shown is Figure 4-82.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.12.4 Schedule Choose menu “Firewall” → “Schedule”, and then you can view and set a Schedule list in the next screen as shown in Figure 4-83. Figure 4-83 Description: Here displays the description of the schedule and this description is unique. Edit: Here you can modify an existing schedule. To add a new schedule, follow the steps below: 1. Click Add New button and the next screen will pop-up as shown in Figure 4-84. 2.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click the Delete Selected button to delete the selected entries in the table. 4.13 Traffic Control There are two submenus under the Traffic Control menu: Control Settings and Rules List. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.13.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-86 Description: This is the information about the rules such as address range. Upstream Bandwidth: This field displays the max and mix upload bandwidth through the WAN port, the default is 0. Downstream Bandwidth: This field displays the max and mix download bandwidth through the WAN port, the default is 0. Edit: Click Edit to modify the rule. To add/modify a Bandwidth Control rule, follow the steps below. 1.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below. 4.14.1 Binding Settings This page displays the IP & MAC Binding Setting table; you can operate it in accord with your desire (shown in Figure 4-88).
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide To modify or delete an existing entry, follow the steps below. 1. Find the desired entry in the table. 2. Click Edit as desired on the Edit column. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete selected entries. 4.14.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-91 Service Provider: This field displays the service provider of DDNS. Domain Name: Enter the Domain name you received from dynamic DNS service provider. Username & Password: Type the “User Name” and “Password” for your DDNS account. Enable DDNS: Activate the DDNS function or not. Login/ Logout: Login to or logout of the DDNS service. 4.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.17 System Tools Choose menu “System Tools”, and you can see the submenus under the main menu: System Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore, Factory Defaults, Firmware Upgrade, Reboot and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.17.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-94 Save Locally: If Save Locally is selected, events will be recorded in the local memory. Minimum Level: Select the Minimum level in the drop-down list, for the Minimum Level, all logged events above or equal to the selected level will be displayed. Save Remotely: If Save Remotely is selected, events will be sent to the specified IP address and UDP port of the remote system log server.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 3. Enter the Time in Hour/Minute/Second format. 4. Click Save. To set time automatically: 1. Select your local time zone. 2. 3. Enter the address or domain of the NTP Server 1 or NTP Server 2. Click the Get GMT button to get system time from Internet if you have connected to the Internet. 4.17.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-97 CWMP: Select enable the CWMP function. Inform: Enable or disable the function. If enabled, the information will be informed to ACS server periodically. Inform Interval: Enter the interval time here. ACS URL: Enter the website of ACS which is provided by your ISP. ACS User Name/Password: Enter the User Name and password to login the ACS server.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-98 An SNMP Agent is an application running on the Modem Router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs. So a router contains SNMP "agent" software can be monitored and/or controlled by SNMP Manager using SNMP messages. 4.17.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-100 Click the Restore button to reset all configuration settings to their default values. The default User Name: admin The default Password: admin The default Subnet Mask: 255.255.255.0 Note: All changed settings will be lost when defaults are restored. 4.17.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1) New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Modem Router rather than the configuration, you can try to upgrade the firmware.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-103 Statistics Status: Enable or Disable. The default value is disabled. To enable it, click the Enable. If it is disabled, the function of DoS protection in Security settings will be disabled. Statistics Interval (5-60): The default value is 10. Select a value between 5 and 60 seconds in the drop-down list. The Packets Statistic interval indicates the time section of the packets statistic.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix A: Specifications General ANSI T1.413.I2, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5, Standards and Protocols IEEE802.1p, IEEE 802.11b,IEEE802.11e, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT Safety & Emission FCC, CE Four 10/100M Auto-Negotiation RJ45 ports（Auto MDI/MDIX) Ports Four RJ11 ports Two USB 2.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my Modem Router’s configuration to its factory default settings? With the Modem Router powered on, press and hold the RESET button on the front panel for 8 to 10 seconds before releasing it. Note: Once the Modem Router is reset, the current configuration settings will be lost and you will need to re-configure the router. T2.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click Change adapter settings Right-click Local Area Connection Click Properties 104
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 105
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide For Windows Vista OS Go to Start > Settings >Control Panel, and then you will see the following page.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 107
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide For Windows XP OS Go to Start > Control Panel, you will then see the following page.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol (TCP/IP) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 109
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click OK 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your Modem Router’s factory default settings and reconfigure your Modem Router following the instructions in 4.1 Login. Please feel free to contact our Technical Support if the problem still exists. T4.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 2) Insert the provided Resource CD into CD-ROM drive of your computer. 3) Please select your product model and click Start Setup. 4) Then the configuration wizard will pop up and show you how to connect your devices. After that, the Easy Setup Assistant will start. Click NEXT, and then follow the step-by-step instructions.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 5) When it comes to Configure USB Voice Mail page, check boxes before Configure USB Voice Mail and Send Files to USB Disk. Then click NEXT to continue. 6) Follow the step-by-step instructions until you comes to the finish screen. Click FINISH to close this wizard.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 7) The configure files can be found in your USB device which means you have successfully configured the USB device for USB Voice Mail function.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix C: Telephony Features This section introduces what the following features are used for. Call Holding This feature allows you to put a call on hold, in which case the call is not ended but no verbal communication is available. To put a call on hold, press the FLASH button. To return to the original call, press the FLASH button again.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Anonymous Call Blocking With this feature enabled, all anonymous calls will be blocked. Speed Dial This feature allows you to create short numbers for your frequently used telephone numbers to make your dialing more convenient. You just need to press one or two digits and the key # instead of the original phone number to make a call.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix D: Telephone Operation The table below guides you to configure some frequently used call features using keypads on your telephone. For the features mentioned in this table, please refer to Telephony Features in Appendix C. Code Description Usage Pick up the phone to dial this code and then follow the voice prompts for the operations below: *20 Listen to voice messages stored in your USB storage device.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide effect. *72 Enable Call Forwarding on Busy. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. *73 Enable Call Forwarding Unconditionally. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect. *69 Dial the last incoming number. Pick up the phone to dial this code.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Disturb). *87 Disable DND (Do Not Disturb). confirmation tone, hang up to make the configuration take effect. Pick up the phone to dial this code. After hearing the confirmation tone, hang up to make the configuration take effect.
TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix E: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details: Global Singapore Tel: +86 755 26504400 Tel: +65 62840493 E-mail: support@tp-link.com E-mail: support.sg@tp-link.
