TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router Rev: 1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2010 TP-LINK TECHNOLOGIES CO., LTD.
Model: TD-W8151N Product Name: 150Mbps Wireless N ADSL2+ Modem Router Corporate Name: TP-LINK USA CORPORATION Corporate Address: 117 n sunset Avenue, City of Industry, CA 91744 Corporate Telephone: 626 333 0234 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
CE Mark Warning This is a class B product. In a domestic environment which case the user may be required to take adequate measures. National Restrictions 2400.0-2483.5 MHz Country Restriction General authorization required for outdoor use and public service Bulgaria France Reason/remark Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N ADSL2+ Modem Router Model No.: TD-W8151N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1.7.
CONTENTS Package Contents .................................................................................................... 1 Chapter 1 Introduction ......................................................................................... 2 1.1 Product Overview.................................................................................. 2 1.2 Main Features ....................................................................................... 2 1.3 Conventions ................................
4.5.6 CWMP ..................................................................................................... 53 4.6 Maintenance........................................................................................ 54 4.6.1 Administration.......................................................................................... 54 4.6.2 Time Zone ............................................................................................... 55 4.6.3 Firmware............................................
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package: ¾ One TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router ¾ One Power Adapter for TD-W8151N ADSL2+ Router ¾ Quick Installation Guide ¾ One RJ45 cable ¾ Two RJ11 cables ¾ One ADSL splitter ¾ One Resource CD , including: z This User Guide z Other Helpful Information ) Note: Make sure that the package contains the above items.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 1 Introduction 1.1 Product Overview Thank you for choosing the TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router. The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network. The TD-W8151N connects to an Ethernet LAN or computers via standard Ethernet ports.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Supports All ADSL industrial standards. ¾ Compatible with all mainstream DSLAM (CO). ¾ Provides integrated access of internet and route function which face to SOHO user. ¾ Real-time Configuration and device monitoring. ¾ Supports Multiple PVC (Permanent Virtual Circuit). ¾ Built-in DHCP server. ¾ Built-in firewall, supporting IP/MAC filter, Application filter and URL filter.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 2 Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs, locating on the front panel, indicates the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Power ADSL Internet WLAN LAN Status Indication Off Power is on. On Power is off. On The LINE port is linked up. Flash The ADSL negotiation is in progress. Off The LINE port is linked down.
TD-W8151N 2.2 150Mbps Wireless N ADSL2+ Modem Router User Guide The Back Panel Figure 2-2 ¾ POWER: The Power plug is where you will connect the power adapter. ¾ ON/OFF: The power switch for the Router. ¾ RESET: There are two ways to reset the Router's factory defaults. Method one: With the Router powered on, use a pin to press and hold the Reset button for at least 5 seconds. And the Router will reboot to its factory default settings.
TD-W8151N 2.3 150Mbps Wireless N ADSL2+ Modem Router User Guide Installation Environment ¾ The Product should not be located where it will be exposed to moisture or excessive heat. ¾ Place the Router in a location where it can be connected to the various devices as well as to a power source. ¾ Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard. ¾ The Router can be placed on a shelf or desktop.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 2-3 7
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3 Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-W8151N or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 ) Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above. Now, you can run the Ping command in the command prompt to verify the network connection.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-6 You can check it follow the steps below: 1) Is the connection between your PC and the Router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-7 Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button. Figure 3-8 Step 2: Configure the time for the Router, and then click the NEXT button. Figure 3-9 Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for example here), and then click the NEXT button.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-10 Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click Next. Figure 3-11 Step 5: Configure the rules for the WLAN, and click NEXT.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-12 ) Note: If the Access Point is activated, the wireless function will be available even without the external antenna because of an additional printed antenna. To adopt the wireless security protection measures, please refer to section 4.3.3. Step 6: Click NEXT to save the current settings. Figure 3-13 Step 7: Click CLOSE to complete.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 4 Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility. After your successful login, you can configure and manage the device.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-2 ) Note: Click the other submenus System Log or Statistics in Figure 4-2, and you will be able to view the system log and traffic statistics about the Router. 4.2 Quick Start Please refer to "3.2: Login". 4.3 Interface Setup Choose “Interface Setup”, you can see the next submenus: Internet and LAN and Wireless. Figure 4-3 Click any of them, and you will be able to configure the corresponding function.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.3.1 Internet Choose “Interface Setup→Internet” menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-4). Figure 4-4 ¾ ¾ ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide PPPoA/PPPoE and Bridge Mode. Please choose the designed type that you want to use. After that, you should follow the configuration below to proceed. 1) Dynamic IP Address Select this option if your ISP provides you an IP address automatically. This option is typically used for Cable services. Please enter the Dynamic IP information accordingly.
TD-W8151N 2) 150Mbps Wireless N ADSL2+ Modem Router User Guide Static IP Address Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below (shown in Figure 4-6). Figure 4-6 ) Note: Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The Router will not accept the IP address if it is not in this format.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-7 ¾ Servicename: Enter a name to mark current connection, or you can leave it blank. ¾ Username: Enter your username for your PPPoE/PPPoA connection. ¾ Password: Enter your password for your PPPoE/PPPoA connection. ¾ Encapsulation: For both PPPoE/PPPoA connection, you need to specify the type of Multiplexing, either LLC or VC Mux. ¾ Bridge Interface: Activate the option, and the Router can also work in Bridge mode.
TD-W8151N 4) 150Mbps Wireless N ADSL2+ Modem Router User Guide Bridge Mode If you select this type of connection, the modem can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. Figure 4-8 ) Note: After you finish the Internet configuration, please click SAVE to make the settings take effect. 4.3.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. ¾ • IP Address: Enter the Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1. • IP Subnet Mask: Enter the Router’s Subnet Mask, the default value is 255.255.255.0.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide • Physical Ports: Specify the Physical Ports of the DHCP client. • DNS Relay: If you want to disable this feature, you just need to set both Primary and secondary DNS IP to 0.0.0.0. If you want to use DNS relay, you can setup DNS server IP to 192.168.1.1 on their Computer. If not, the device will perform as no DNS relay. • Primary DNS Server: Type in your preferred DNS server. • Secondary DNS Server: Type in your preferred DNS server.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-12 ¾ Access Point Settings: These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network.
TD-W8151N ¾ ¾ 150Mbps Wireless N ADSL2+ Modem Router User Guide • Access Point: Select Activated to allow wireless station to associate with the access point. • Channel: Select the country and channel you want to use from the drop-down List of Channel. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. • Beacon Interval: Enter a value between 20-1000 milliseconds.
TD-W8151N • 150Mbps Wireless N ADSL2+ Modem Router User Guide Use QSS: Use QSS (Wi-Fi Protected Setup) function, you can add a new wireless device to an existing network quickly. To Use QSS, keep the default setting, and configure the parameters in QSS Settings. If you don’t want to Use QSS, select “No”, then you will see the screen as shown below. Figure 4-13 • SSID: Wireless network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network.
TD-W8151N 2) 150Mbps Wireless N ADSL2+ Modem Router User Guide WEP-128Bits To configure WPA-128Bits settings, select the WPA-128Bits option from the drop-down list. The menu will change to offer the appropriate settings. 128-bit is stronger than 64-bit. Figure 4-15 3) WPA-PSK To configure WPA-PSK settings, select the WPA-PSK option from the drop-down list. The menu will change to offer the appropriate settings. WPA-PSK requires a shared key and does not use a separate server for authentication.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-17 5) WPA-PSK/WPA2-PSK To configure WPA-PSK/WPA2-PSK settings, select the WPA-PSK/WPA2-PSK option from the drop-down list. The menu will change to offer the appropriate settings. WPA-PSK/WPA2-PSK requires a shared key and does not use a separate server for authentication. PSK keys can be ASCII or Hex type. Figure 4-18 ¾ QSS Settings: QSS can help you to add a new wireless device to an existing network quickly.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Method One: Step 1: Press the QSS button on the front panel of the Router or click Start QSS button in Figure 4-19. Step 2: Press and hold the QSS button of the adapter directly for 2 or 3 seconds. Step 3: Wait for a while until the next screen appears. Click Finish to complete the QSS configuration.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide The QSS Configuration Screen of Wireless Adapter Step 3: Wait for a while until the next screen appears. Click Finish to complete the QSS configuration. The QSS Configuration Screen of Wireless Adapter 2) PIN code If the wireless adapter supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Click PIN code, you will see the screen as shown below.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-20 Method One: Enter the PIN into my Router Step 1: For the configuration of the wireless adapter, please choose “Enter a PIN into my access point or a registrar” in the configuration utility of the QSS, and get the PIN code on the screen as below, then click Next.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-21 Method Two: Enter the PIN from my Router Step 1: Get the Current PIN code of the Router from AP self PIN code in Figure 4-21 (each Router has its unique PIN code. Here takes the PIN code 55924054 of this Router for example).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all stations in your wireless network. Type the desired SSID in the space provided. • Authentication Type: Select an authentication type from the drop-down list, which allows you to configure security features of the wireless LAN interface.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack. ¾ SPI: If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side. 4.4.2 Routing Choose “Advanced Setup→Routing” menu, and you will see the routing information in the next screen (shown in Figure 4-24). Figure 4-24 Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-25).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.3 NAT Choose “Advanced Setup→NAT” menu, you can setup the NAT (Network Address Translation) function for the Router (shown in Figure 4-26). Figure 4-26 ¾ Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function. ¾ NAT Status: This field shows the current status of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-4) to activate the function.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.3.2 Virtual Server Choose “Advanced Setup→NAT→Virtual Server” in Figure 4-26, you can configure the Virtual Server in the next screen. The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 3: Select the application you want from drop-down list, then the protocol and port number will be added to the corresponding field automatically, you only need to configure the IP address for the virtual server; If the application list does not contain the service that you want, please configure the Port number, IP Address and Protocol manually. Step 4: After that, click SAVE to make the entry take effect.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide ) Note: IP Address Mapping is only available for VCs with Multiple IPs. Step 2: Select the Rule index for the rule as shown in Figure 4-29. Step 3: Select the rule type you want from the drop-down list. Step 4: Enter the local and public IP addresses in the corresponding fields. Step 5: After that, click SAVE to make the entry take effect.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-30 ¾ QoS: Select this option to Activate/Deactivate the IP QoS on different types (IP ToS and DiffServ). ¾ Summary: Click the QoS Settings Summary button to view the configurations of QoS. ¾ Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will take the corresponding action to deal with it. • Rule Index: Select the index for the rule you want to configure. • Active: Activate the rule.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide • Protocol ID: Select one among TCP/UDP, TCP, UDP or ICMP protocols for the application. • Vlan ID Range: Enter the Vlan range, and the rule will be effective to the selected Vlans. • IPP/DS Field: Select the type of the action to assign the priority. When you select IPP/TOS, you can assign the priority via IP information.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-31 1) Assign VLAN PVID for each Interface Click Assign VLAN PVID for each Interface in Figure 4-31, you can assign the PVID for each interface in the next screen (shown in Figure 4-32). Figure 4-32 ¾ PVID: Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-33 ¾ VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum. ¾ VLAN ID: This indicates the VLAN group. ¾ ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the VC. ¾ Ethernet: Select the Ethernet port as a member of VLAN.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-34 ¾ ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ¾ ADSL Type: Select the ADSL operation type which your ADSL connection uses. ¾ Bitswap Enable: Check this box to enable Bitswap. ¾ SRA Enable: Check this box to enable SRA. 4.5 Access Management Choose “Access Management”, you can see the next submenus: Figure 4-35 Click any of them, and you will be able to configure the corresponding function. 4.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-36 ¾ ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated, all IP addresses can access to the Router. ¾ ACL Rule Index: Select the ACL rule index for the entry. ¾ Active: Enable the ACL rule. ¾ Secure IP Address: Select the IP addresses which are permitted to access to the Router remotely. With the default IP 0.0.0.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-37 ¾ Filter Type Selection: Select the filter type for the configuration below. ¾ IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes. ¾ Interface: Select the interface for the entry. ) Note: If select PVC0~PVC7 as an interface, the filter will match the IP traffic of WAN port with specified IPs (Source IP Address and Destination IP Address).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide ) Note: Incoming means that IP traffic which is coming into the Router, and the Outgoing means that IP traffic which is going out the Router. ¾ IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry. ) Note: You should set the IP/MAC Filter Set Index and IP/MAC Filter Rule Index together to appoint the address (shown in the Filter List) for the IP Filter rule.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide ) Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “Source IP Address”, “Destination IP Address”, “Subnet Mask” and “Port Number” in the corresponding field. Step 4: Select the Protocol as “TCP” and select the Unmatched rule as “Next”. Step 5: Finally, click the SAVE to save the entry. Step 6: Go to Step 2 to configure the next two rules: Block E-mail received by the IP address 192.168.1.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.2.2 MAC Filter Select IP/Mac Filter as the Filter type, and select MAC as the Rule type (shown in Figure 4-38), and then you can configure the filter rules based on MAC address. Figure 4-38 ¾ Rule Type: Select MAC for the MAC Filter rule. ¾ Active: Select “Yes” to make the rule to take effect. ¾ MAC Address: Enter the MAC address for the rule.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface “PVC0”, and select the Direction “Outgoing” for the first rule. ) Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “MAC Address” and select the Unmatched rule as “Next”. Step 4: Finally, click the SAVE to save the entry.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-39 ¾ Filter Type Selection: Select the Application Filter for the next configuration. ¾ Application Filter: Activate or deactivate the function. ¾ ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If you select Allow, the Router will accept the application; if you select Deny, the Router will forbid the application. 4.5.2.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-40 ¾ Filter Type Selection: Select the URL Filter for the next configuration. ¾ Active: Select “Yes” to make the rule to take effect. ¾ URL Index: Select the index for the URL Filter entry. ¾ URL: Enter the URL for this URL Filter. ¾ URL Filter Listing: This displays the information about the URL Filter rules. To add a URL filter entry: For example: If you want to forbid the user to access the website: www.yahoo.com.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Management Protocol (SNMP) is used for exchanging information between network devices. Figure 4-41 ¾ Get Community: Set the password for the incoming Get and Get next requests from the management station. ¾ Set Community: Set the password for incoming Set requests from the management station. 4.5.4 UPnP Choose “Access Management→UPnP”, you can configure the UPnP in the screen (shown in Figure 4-42).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-43 ¾ Dynamic DNS: Activate the DDNS function or not. ¾ Service Provider: This field displays the service provider of DDNS. ¾ My Host Name: Enter your host name here. ¾ E-mail Address: Enter your E-mail address here. ¾ Username & Password: Type the “User Name” and “Password” for your DDNS account. ¾ Wildcard support: Select the option to use Wildcard function 4.5.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-44 ¾ CWMP: Select activate the CWMP function. ¾ URL: Enter the website of ACS which is provided by your ISP. ¾ User Name/Password: Enter the User Name and password to login the ACS server. ¾ Path: Enter the path that connects to the ACS server. ¾ Port: Enter the port that connects to the ACS server. ¾ User Name/Password: Enter the User Name and Password that provided the ACS server to login the Router.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-46 ) Note: 1) There is only one account that can access Web-Management interface. The default account is "admin", and the password is "admin". Admin has read/write access privilege. 2) When you change the password, you should enter the new password twice, and then click SAVE to make the new password take effect. 4.6.2 Time Zone Choose “Maintenance→Time Zone”, you can configure the system time in the screen (shown in Figure 4-47).
TD-W8151N 2) 150Mbps Wireless N ADSL2+ Modem Router User Guide PC’s Clock Select PC’s Clock as the Synchronize time, you don’t need to set any items. Figure 4-48 3) Manually Select Manually as the Synchronize time, you need to set the date and time corresponding to the current time. Figure 4-49 4.6.3 Firmware Choose “Maintenance→Firmware”, you can upgrade the firmware of the Router in the screen (shown in Figure 4-50).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-50 To upgrade the Router's firmware, follow these instructions below: Step 1: Download a more recent firmware upgrade file from the TP-LINK website (http://www.tp-link.com). Step 2: Type the path and file name of the update file into the “New Firmware Location” field. Or click the Browse… button to locate the update file. Step 3: Click the UPGRADE button. ) Note: 1) New firmware versions are posted at http://www.tp-link.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-51 Step 2: Save the file as the appointed file (shown in Figure 4-52). Figure 4-52 To restore the Router’s settings: Step 1: Click the Browse… button to locate the update file for the device, or enter the exact path in “New Romfile Location” field. Step 2: Click the UPGRADE button to complete. 4.6.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-53 4.6.5 Diagnostics Choose “Maintenance→Diagnostics”, you can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in the screen (shown in Figure 4-54). Figure 4-54 Ping Tool: This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. ¾ IP Address/Domain Name: Type the destination IP address (such as 202.108.22.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide If the result is similar to Figure 4-55, the connectivity of the Internet is fine. Figure 4-55 If the result is similar to Figure 4-56, there is something wrong with the connectivity of the Internet. Figure 4-56 4.7 Help Choose “Help”, you can view the help information for configuration of any function.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-57 ) Note: Click the tab, and you will be able to get the corresponding information.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A: Specification General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5 Standards and Protocols IEEE 802.11n, IEEE 802.11b, IEEE 802.11g ,IEEE 802.3, IEEE 802.
