TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router Rev: 3.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada.
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ●注意防潮,請勿將水或其他液體潑灑到本產品上。 ●插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。 ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不可放在密閉位置中。 ●請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作。 UkrSEPRO Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N ADSL2+ Modem Router Model No.
CONTENTS Chapter 1 Introduction ......................................................................................... 2 1.1 Product Overview.................................................................................. 2 1.2 Main Features ....................................................................................... 2 1.3 Conventions .......................................................................................... 3 Chapter 2 Hardware Installation..........................
4.5.4 UPnP ....................................................................................................... 62 4.5.5 DDNS ...................................................................................................... 62 4.5.6 CWMP ..................................................................................................... 63 4.6 Maintenance........................................................................................ 64 4.6.1 Administration................................
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package: One TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router One Power Adapter for TD-W8151N ADSL2+ Router Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter One Resource CD , including: This User Guide Other Helpful Information Note: Make sure that the package contains the above items.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 1 Introduction 1.1 Product Overview Thank you for choosing the TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router. The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network. The TD-W8151N connects to an Ethernet LAN or computers via standard Ethernet ports.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Supports All ADSL industrial standards. Compatible with all mainstream DSLAM (CO). Provides integrated access of internet and route function which face to SOHO user. Real-time Configuration and device monitoring. Supports Multiple PVC (Permanent Virtual Circuit). Built-in DHCP server. Built-in firewall, supporting IP/MAC filter, Application filter and URL filter.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 2 Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs located on the front panel indicates the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name (Power) (ADSL) (Internet) (WLAN) (WPS) (LAN) Status Indication On The modem router is powered on. Off The modem router is off. Please ensure that the power adapter is connected correctly.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide please refer to Note 1. If your ADSL LED is GREEN ON, please check your Internet configuration. You may need to check this part of information with your ISP and make sure everything have been input correctly. Refer to 4.1.1 Device Info and 4.3.1 Internet for more information. 2.2 The Back Panel Figure 2-2 POWER: The Power plug is where you will connect the power adapter. ON/OFF: The switch for the Router.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide ADSL: Through the port, you can connect the Router with the telephone. Or you can connect them by an external separate splitter. For details, please refer to “2.4 Connecting the Modem Router”. Antenna: Used for wireless operation and data transmit. 2.3 Installation Environment The Product should not be located where it will be exposed to moisture or excessive heat.
TD-W8151N 2.4 150Mbps Wireless N ADSL2+ Modem Router User Guide Connecting the Modem Router Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and keep your hands dry. You can follow the steps below to install it. Step 1: Connect the ADSL Line.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3 Quick Installation Guide 3.1 TCP/IP Configuration The default IP address of the TD-W8151NTD-W8151N 150Mbps Wireless N ADSL2+ Modem Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description. Connect the local PC to the LAN port of the Modem Router.
TD-W8151N 1) 150Mbps Wireless N ADSL2+ Modem Router User Guide Is the connection between your PC and the modem router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the modem router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-4 Step 2: Configure the time for the Router, and then click the NEXT button. Figure 3-5 Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for example here), and then click the NEXT button. Figure 3-6 Step 4: There are four connection types: Dynamic IP Address, Static IP Address, PPPoE/PPPoA and Bridge Mode. Please choose the connection type that your ISP provides.
TD-W8151N 1) 150Mbps Wireless N ADSL2+ Modem Router User Guide Select Dynamic IP Address in Figure 3-6, the next screen will appear as shown in Figure 3-7. Configure the following options provided by your ISP: VPI, VCI and Connection Type. Then click NEXT. Figure 3-7 2) Select Static IP Address in Figure 3-6, the next screen will appear as shown in Figure 3-8.Configure the following options provided by your ISP: VPI, VCI, IP Address, Subnet Mask, ISP Gateway and Connection Type. Then click NEXT.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Note: If Use Auto Discovered DNS Server Only is selected in DNS Relay, this modem router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If Use User Discovered DNS Server Only is selected in DNS Relay, it is necessary for you to enter the primary and optional secondary DNS server IP addresses.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-11 Note: If the Access Point is activated, the wireless function will be available even without the external antenna because of an additional printed antenna. To adopt the wireless security protection measures, please refer to 4.3.3 Wireless. Step 6: Click NEXT to save the current settings. Figure 3-12 Step 7: Click CLOSE to complete.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 4 Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility. After your successful login, you can configure and manage the device.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-2 Note: Click the other submenus System Log or Statistics in Figure 4-2, and you will be able to view the system log and traffic statistics about the Router. 4.1.2 System Log Choose “Status→System Log” menu, and you will be able to query the logs of the Router.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-3 The Router can keep logs of all traffic. You can query the logs to find what happened to the Router. Click the CLEAR LOG button to clear the logs. Click the SAVE LOG button to save the logs. 4.1.3 Statistics Choose “Status→Statistics” menu, and you will be able to view the network traffic over Ethernet, ADSL and WLAN.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-4 Interface: You can select Ethernet, ADSL and WLAN to view the corresponding network traffic over different ports. Select Ethernet, and you will see the statistics table as below. Statistics Table: Transmit Statistics Receive Statistics Transmit Frames The frames transmitted over the Ethernet port. Transmit Multicast Frames The multicast frames transmitted over the Ethernet port.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Statistics Table: Transmit Statistics Receive Statistics Transmit total PDUs The total PDUs transmitted over the ADSL port. Transmit total Error Counts The total errors occurred over the ADSL port when data is being transmitted. Receive total PDUs The total PDUs transmitted over the ADSL port. Receive total Error Counts The total errors occurred over the ADSL port when data is being received.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-5 Click any of them, and you will be able to configure the corresponding function. 4.3.1 Internet Choose “Interface Setup→Internet” menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-6). Figure 4-6 ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide VCI: Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value provided by your ISP. PVCs Summary: Click the button, and you can view the summary information about the PVCs.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Default Route: If enable this function, the current PVC will be considered as the default gateway to Internet from this device. TCP MTU Option: Enter the TCP MTU as your desire. The default value is 1500. IPv4 Address: If you select IPv4 as IP version, you should configure the following. NAT: Select this option to Enable/Disable the NAT (Network Address Translation) function for this VC.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-8 Note: Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The modem router will not accept the IP address if it is not in this format. 3) PPPoA/PPPoE Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL services.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-9 Service name: Specify a name for the PPPoA/PPPoE connection for recognition. Username: Enter your username for your PPPoA/PPPoE connection to identify and verify your account to the ISP. Password: Enter your password for your PPPoA/PPPoE connection. Encapsulation: For both PPPoA/PPPoE connection, you need to specify the type of Multiplexing, either LLC or VC Mux.
TD-W8151N 4) 150Mbps Wireless N ADSL2+ Modem Router User Guide Bridge Mode If you select this type of connection, the modem router can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. Figure 4-10 Note: After you finish the Internet configuration, please click SAVE to make the settings take effect. 4.3.1.2 IPv6 There are two IP versions: IPv4 and IPv6.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-11 IP Common Option: Configure the IP common option here. Encapsulation: Select the encapsulation mode for the Dynamic IP Address, you can leave it default. Bridge Interface: Activate the option, the modem router can also work in Bridge mode. Default Route: If enable this function, the current PVC will be considered as the default gateway to Internet from this device. TCP MTU Option: Enter the TCP MTU as your desire.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-12 Note: Each IP address entered in the fields must be in the appropriate IPv6 form, which is eight IP octets separated by a colon (x:x:x:x:x:x:x:x). The modem router will not accept the IP address if it is not in this format. 3) PPPoA/PPPoE Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL services.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-13 Service name: Specify a name for the PPPoA/PPPoE connection for recognition. Username: Enter your username for your PPPoA/PPPoE connection to identify and verify your account to the ISP. Password: Enter your password for your PPPoA/PPPoE connection. Encapsulation: For both PPPoA/PPPoE connection, you need to specify the type of Multiplexing, either LLC or VC Mux.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide disable the function, please click Disable. MLD Proxy: The MLD (Multicast Listener Discovery Protocol) Proxy function is enabled by default. If you want to disable the function, please click Disable. Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by default.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-15 Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. IP Address: Enter the Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Protocol) is a session-layer protocol used to establish membership in a multicast group. The ADSL ATU-R supports IGMP version 1 (IGMP v1), IGMP v2 and IGMP v3. Select “Disabled” to disable it. IGMP Snoop: Enable the IGMP Snoop function if you need. DHCP Server: Select Enabled, then you will see the screen below (shown in Figure 4-16). The Router will work as a DHCP Server; it becomes the default gateway for DHCP client connected to it.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide DHCP Relay: Select Relay, then you will see the next screen (shown in Figure 4-17), and the Router will work as a DHCP Relay. A DHCP relay is a computer that forwards DHCP data between computers that request IP addresses and the DHCP server that assigns the addresses. Each of the device's interfaces can be configured as a DHCP relay. If it is enabled, the DHCP requests from local PCs will forward to the DHCP server runs on WAN side.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide seconds. Valid lifetime: The valid lifetime for the prefix. The default value is 2592000 seconds. RA Flags Set: You can select ManagedAddr ,Other Config or both. If you select ManagedAddr, you should enable DHCPv6 Server (shown in Figure 4-20). DHCPv6:DHCPv6 is provided to assign IPv6 addresses and DNS to the computers in your LAN. Enable this function if needed.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-22 33
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Access Point Settings: These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network. Access Point: Select Activated to allow wireless station to associate with the access point. Transmit Power: Here you can specify the transmit power of Router. You can select High, Medium or Low which you would like.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Multiple SSIDs Settings: These are the settings of the SSID. SSID Index: The index of the SSID, and in this model, you can only leave it as a default value of 1. Broadcast SSID: When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. To broadcast the Router’s SSID, keep the default setting. If you don’t want to broadcast the Router’s SSID, select “No”.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-24 2) WEP-128Bits To configure WEP-128Bits settings, select the WEP-128Bits option from the drop-down list. The menu will change to offer the appropriate settings. 128-bit is stronger than 64-bit. Figure 4-25 3) WPA-PSK To configure WPA-PSK settings, select the WPA-PSK option from the drop-down list. The menu will change to offer the appropriate settings.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Encryption: Select the encryption you want to use: TKIP or AES (AES is an encryption method stronger than TKIP). TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Button Configuration (PBC) method or PIN method, please select the one you want. WPS progress: Show the current WPS progress. Reset to OOB: Use this button to reset the WPS state to “unconfigured”, so that a new key will be created when using WPS function next time.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Method Two: Step 1: Press the WPS button on the back panel of the Router or click Start WPS button in Figure 4-29. Step 2: For the configuration of the wireless adapter, please choose “Push the button on my access point” in the configuration utility of the WPS as below, and click Next.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter 2) PIN code If the wireless adapter supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Click PIN code, you will see the screen as shown below.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-30 Method One: Enter the PIN into my Router Step 1: For the configuration of the wireless adapter, please choose “Enter a PIN into my access point or a registrar” in the configuration utility of the WPS, and get the PIN code on the screen as below, then click Next.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-31 Method Two: Enter the PIN from my Router Step 1: Get the Current PIN code of the Router from AP self PIN code in Figure 4-31 (each Router has its unique PIN code. Here takes the PIN code 55924054 of this Router for example).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide is the same for all stations in your wireless network. Type the desired SSID in the space provided. Authentication Type: Select an authentication type from the drop-down list, which allows you to configure security features of the wireless LAN interface. Options available are: Disabled, WEP-64Bits, WEP-128Bits, WPA-PSK, WPA2-PSK, and WPA-PSK/ WPA2-PSK. WDS Settings: Select On/Off to enable/disable WDS.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Note: To enable the function, there should not have any IPv6 WAN connections.. 4.4 Advanced Setup Choose “Advanced Setup”, you can see the next submenus: Figure 4-33 Click any of them, and you will be able to configure the corresponding function. 4.4.1 Firewall Choose “Advanced Setup→Firewall” menu, and you will see the next screen (shown in Figure 4-34).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-35 Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-36). Figure 4-36 Destination IP Address: This parameter specifies the IP network address of the final destination. IP Subnet Mask: Enter the subnet mask for this destination. Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packet to the destination.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-37 Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function. NAT Status: This field shows the current status of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-6) to activate the function. Number of IPs; This field is to specify how many IPs are provided by your ISP for current VC. It can be single IP or multiple IPs. We select Multiple to explain.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. Figure 4-39 Rule Index: The Virtual server rule index for this VC. You can specify 12 rules in maximum. All the VCs with single IP will use the same Virtual Server rules.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Enter the index of assigned entry, and click the DELETE button to delete the entry. Click the BACK button to return to the previous screen. Click the CANCEL button to cancel the configuration which is made just now. 4.4.3.3 IP Address Mapping Select Multiple for numbers of IPs in Figure 4-37, and choose “Advanced Setup→NAT→IP Address Mapping(for Multiple IP Service)”. You can configure the Address Mapping Rule in the next screen.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 5: After that, click SAVE to make the entry take effect. Other operations for the entries as shown in Figure 4-40: Select the index of assigned entry, and click the DELETE button to delete the entry. Click the BACK button to return to the previous screen. Click the CANCEL button to cancel the configuration which is made just now. 4.4.4 QoS Choose “Advanced Setup→QoS”, you can configure the QoS in the next screen.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide QoS: Select this option to Activate/Deactivate the IP QoS on different types (IP ToS and DiffServ). Summary: Click the QoS Settings Summary button to view the configurations of QoS. Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will take the corresponding action to deal with it. Rule Index: Select the index for the rule you want to configure. Active: Activate the rule.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows: 1) Port-Based VLAN: Each physical switch port is configured with an access list specifying membership in a set of VLANs.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Click Define VLAN Group in Figure 4-42, you can define VLAN groups in the next screen (shown in Figure 4-44). Figure 4-44 VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum. VLAN ID: This indicates the VLAN group. ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the VC.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-45 ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ADSL Type: Select the ADSL operation type which your ADSL connection uses. Bitswap Enable: Check this box to enable Bitswap. SRA Enable: Check this box to enable SRA. 4.5 Access Management Choose “Access Management”, you can see the next submenus: Figure 4-46 Click any of them, and you will be able to configure the corresponding function. 4.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-47 ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated, all IP addresses can access to the Router. ACL Rule Index: Select the ACL rule index for the entry. Active: Enable the ACL rule. Secure IP Address: Select the IP addresses which are permitted to access to the Router remotely. With the default IP 0.0.0.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-48 Filter Type Selection: Select the filter type for the configuration below. IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes. Interface: Select the interface for the entry. Note: If select PVC0~PVC7 as an interface, the filter will match the IP traffic of WAN port with specified IPs (Source IP Address and Destination IP Address).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Note: Incoming means that IP traffic which is coming into the Router, and the Outgoing means that IP traffic which is going out the Router. IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry. Note: You should set the IP/MAC Filter Set Index and IP/MAC Filter Rule Index together to appoint the address (shown in the Filter List) for the IP Filter rule.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “Source IP Address”, “Destination IP Address”, “Subnet Mask” and “Port Number” in the corresponding field. Step 4: Select the Protocol as “TCP” and select the Unmatched rule as “Next”. Step 5: Finally, click the SAVE to save the entry. Step 6: Go to Step 2 to configure the next two rules: Block E-mail received by the IP address 192.168.1.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.2.2 MAC Filter Select IP/MAC Filter as the Filter type, and select MAC as the Rule type (shown in Figure 4-49), and then you can configure the filter rules based on MAC address. Figure 4-49 Rule Type: Select MAC for the MAC Filter rule. Active: Select “Yes” to make the rule to take effect. MAC Address: Enter the MAC address for the rule.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface “PVC0”, and select the Direction “Outgoing” for the first rule. Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “MAC Address” and select the Unmatched rule as “Next”. Step 4: Finally, click the SAVE to save the entry.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-50 Filter Type Selection: Select the Application Filter for the next configuration. Application Filter: Activate or deactivate the function. ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If you select Allow, the Router will accept the application; if you select Deny, the Router will forbid the application. 4.5.2.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-51 Filter Type Selection: Select the URL Filter for the next configuration. Active: Select “Yes” to make the rule to take effect. URL Index: Select the index for the URL Filter entry. URL: Enter the URL for this URL Filter. URL Filter Listing: This displays the information about the URL Filter rules. To add a URL filter entry: For example: If you want to forbid the user to access the website: www.yahoo.com.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.3 SNMP Choose “Access Management→SNMP”, you can see the SNMP screen. The Simple Network Management Protocol (SNMP) is used for exchanging information between network devices. Figure 4-52 Get Community: Set the password for the incoming Get and Get next requests from the management station. Set Community: Set the password for incoming Set requests from the management station. 4.5.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide static host name with a dynamic IP address. User should type the host name, user name and password assigned to your ADSL Router by your Dynamic DNS provider. User also can decide to turn on DYNDNS Wildcard or not. Figure 4-54 Dynamic DNS: Activate the DDNS function or not. Service Provider: This field displays the service provider of DDNS. My Host Name: Enter your host name here. E-mail Address: Enter your E-mail address here.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-55 CWMP: Select activate the CWMP function. URL: Enter the website of ACS which is provided by your ISP. User Name/Password: Enter the User Name and password to login the ACS server. Path: Enter the path that connects to the ACS server. Port: Enter the port that connects to the ACS server. User Name/Password: Enter the User Name and Password that provided the ACS server to login the Router.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-57 Note: 1) There is only one account that can access Web-Management interface. The default account is "admin", and the password is "admin". Admin has read/write access privilege. 2) When you change the password, you should enter the new password twice, and then click SAVE to make the new password take effect. 4.6.2 Time Zone Choose “Maintenance→Time Zone”, you can configure the system time in the screen (shown in Figure 4-58).
TD-W8151N 2) 150Mbps Wireless N ADSL2+ Modem Router User Guide PC’s Clock Select PC’s Clock as the Synchronize time, you don’t need to set any items. Figure 4-59 3) Manually Select Manually as the Synchronize time, you need to set the date and time corresponding to the current time. Figure 4-60 4.6.3 Firmware Choose “Maintenance→Firmware”, you can upgrade the firmware of the Router in the screen (shown in Figure 4-61).
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-61 To upgrade the Router's firmware, follow these instructions below: Step 1: Download a more recent firmware upgrade file from the TP-LINK website (http://www.tp-link.com). Step 2: Type the path and file name of the update file into the “New Firmware Location” field. Or click the Browse… button to locate the update file. Step 3: Click the UPGRADE button. Note: 1) New firmware versions are posted at http://www.tp-link.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-62 Step 2: Save the file as the appointed file (shown in Figure 4-63). Figure 4-63 To restore the Router’s settings: Step 1: Click the Browse… button to locate the update file for the device, or enter the exact path in “New Romfile Location” field. Step 2: Click the UPGRADE button to complete. 4.6.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-64 4.6.5 Diagnostics Choose “Maintenance→Diagnostics”, you can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in the screen (shown in Figure 4-65). Figure 4-65 Ping Tool: This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide IP Address/Domain Name: Type the destination IP address (such as 202.108.22.5) or Domain name (such as http://www.tp-link.com). If the result is similar to Figure 4-66, the connectivity of the Internet is fine. Figure 4-66 If the result is similar to Figure 4-67, there is something wrong with the connectivity of the Internet. Figure 4-67 4.7 Help Choose “Help”, you can view the help information for configuration of any function.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-68 Note: Click the tab, and you will be able to get the corresponding information.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A: Specification General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5 Standards and Protocols IEEE 802.11n, IEEE 802.11b, IEEE 802.11g ,IEEE 802.3, IEEE 802.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my Router’s configuration to its factory default settings? With the Router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it. Note: Once the Router is reset, the current configuration settings will be lost and you will need to re-configure the router. T2.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Click Network Connections Right-click Local Area Connection Click Properties 74
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Protocol (TCP/IP) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 75
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Click OK 76
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide For Windows Vista OS Go to Start > Settings >Control Panel, and then you will see the following page.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 78
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide For Windows 7 OS Go to Start > Settings > Control Panel, and then you will see the following page.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK 80
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your Router’s factory default settings and reconfigure your Router following the instructions in 3.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4) If you still cannot access the Internet, please restore your modem router to its factory default settings and reconfigure your modem router by following the instructions in 3.2 Login. 5) Please feel free to contact our Technical Support if the problem still exists. Note: For more details about Troubleshooting and Technical Support contact information, please log on to our Technical Support Website: http://www.tp-link.com/en/support.
TD-W8151N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix C: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details: Global Singapore Tel: +86 755 2650 4400 Tel: +65 6284 0493 Fee: Depending on rate of different carriers, IDD.