TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router REV:2.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device.
射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。 減少電磁波影響，請妥適使用。 安全諮詢及注意事項 ●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ●注意防潮，請勿將水或其他液體潑灑到本產品上。 ●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 ●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 UkrSEPRO Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N ADSL2+ Modem Router Model No.
CONTENTS Chapter 1 Introduction ......................................................................................... 1 1.1 Product Overview.................................................................................. 1 1.2 Main Features ....................................................................................... 1 1.3 Conventions .......................................................................................... 2 Chapter 2 Hardware Installation..........................
4.5.2 Filter ........................................................................................................ 53 4.5.3 SNMP ...................................................................................................... 61 4.5.4 UPnP ....................................................................................................... 61 4.5.5 DDNS ...................................................................................................... 62 4.5.6 CWMP ............................
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 1 Introduction Thank you for choosing the TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router. 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network. The TD-W8961N connects to an Ethernet LAN or computers via standard Ethernet ports.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Supports PPPoE, it allows connecting the internet on demand and disconnecting from the Internet when idle. Provides reliable ESD and surge-protect function with quick response semi-conductive surge protection circuit. High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth. Supports All ADSL industrial standards. Compatible with all mainstreams DSLAM (CO).
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 2 Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel. They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Status On (Power) (ADSL) Flash System initializing or firmware upgrading is in process. Do not disconnect or power off the modem router. Power is off. On ADSL line is synchronized and ready to use.
TD-W8961N Name Status On (LAN1-4) 300Mbps Wireless N ADSL2+ Modem Router User Guide Flash Off Indication The corresponding LAN port is connected. The modem router is sending or receiving data over this LAN port. The corresponding LAN port is not connected. Note: 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly.
TD-W8961N 2.2 300Mbps Wireless N ADSL2+ Modem Router User Guide The Back Panel LAN LAN LAN LAN Figure 2-2 POWER: The Power plug is where you will connect the power adapter. ON/OFF: The switch for the power. WiFi: The button for the wireless function. WPS/RESET: The switch for the WPS function.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Method two: Restore the default setting from “Maintenance-SysRestart” of the modem router's Web-based Utility. LAN 1, LAN 2, LAN 3, LAN 4: Through the port, you can connect the modem router to your PC or the other Ethernet network devices. ADSL: Through the port, you can connect the modem router with the telephone. Or you can connect them by an external separate splitter. For details, please refer to 2.4 Connecting the Modem Router. 2.
TD-W8961N 2.4 300Mbps Wireless N ADSL2+ Modem Router User Guide Connecting the Modem Router Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and keep your hands dry. You can follow the steps below to install it. Step 1: Connect the ADSL Line.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide LAN LAN Figure 2-3 8 LAN LAN
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3 Quick Installation Guide This chapter will show you how to configure the basic functions of your TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-2 You can check it by following the steps below: 1) Is the connection between your PC and the router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 1: Click the NEXT button. Figure 3-4 Step 2: Configure the time zone for the modem router, and then click the NEXT button.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 3: Select your country and ISP, and select your ISP Connection type (Here we take PPPoE/PPPoA mode for example), and complete the corresponding settings with the information provided by your ISP, then click the NEXT button. Figure 3-6 Note: Per FCC regulations, all Wi-Fi products marketed in the U.S. must be fixed to the U.S. region only.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4: Configure the rules for the Wlan, and click the NEXT button. Figure 3-7 Note: If the Access Point is activated, the wireless function will be available even without the external antenna because of an additional printed antenna. To adopt the wireless security protection measures, please refer to section 4.3.3. Step 5: Click SAVE to finish the Quick Start.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 4 Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility. After your successful login, you can configure and manage the device.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-2 4.1.2 System Log Choose “Status→System Log” menu, and you will be able to query the logs of the modem router.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-3 The modem router can keep logs of all traffic. You can query the logs to find what happened to the modem router. Click the CLEAR LOG button to clear the logs. Click the SAVE LOG button to save the logs. 4.1.3 Statistics Choose “Status→Statistics” menu, and you will be able to view the network traffic over Ethernet, ADSL and WLAN.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-4 Interface: You can select Ethernet, ADSL and WLAN to view the corresponding network traffic over different ports. Select Ethernet, and you will see the statistics table as below. Statistics Table: Transmit Frames Transmit Multicast Frames Transmit Statistics Transmit total Bytes Transmit Collision Transmit Error Frames The multicast frames transmitted over the Ethernet port.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Select ADSL, and you will see the statistics table as below. Statistics Table: Transmit Statistics Receive Statistics The total PDUs transmitted over the ADSL port. Transmit total PDUs Transmit total Error Counts The total errors occurred over the ADSL port when data is being transmitted. The total PDUs transmitted over the ADSL port.
TD-W8961N 4.3 300Mbps Wireless N ADSL2+ Modem Router User Guide Interface Setup Choose “Interface Setup”, you can see the following submenus: Internet, LAN, Wireless, 6RD, Guest Network. Figure 4-5 Click any of them, and you will be able to configure the corresponding function. 4.3.1 Internet Choose “Interface Setup→Internet” menu, you can configure the parameters for WAN ports in the following screen.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-6 ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide need to activate the VC to take effect. For PVCs management, you can use ATM QoS to setup each PVC traffic line's priority. Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7. PVCs Summary: Click the button, and you can view the summary information about the PVCs. Status: If you want to use a designed VC, you should activate it. VPI: Identifies the virtual path between endpoints in an ATM network.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Default Route: If enable this function, the current PVC will be considered as the default gateway to internet from this device. TCP MTU Option: Enter the TCP MTU as your desire. NAT: Select this option to Enable/Disable the NAT (Network Address Translation) function for this VC. The NAT function can be activated or deactivated per PVC basis.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The modem router will not accept the IP address if it is not in this format. 3) PPPoA/PPPoE Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL services.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Servicename: Enter a name to mark current connection, or you can leave it blank. Username: Enter your username for your PPPoA/PPPoE connection. Password: Enter your password for your PPPoA/PPPoE connection. Encapsulation: For both PPPoA/PPPoE connection, you need to specify the type of Multiplexing, either LLC or VC Mux. Bridge Interface: Activate the option, and the modem router can also work in Bridge mode.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide If you select this type of connection, the modem can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. Note: After you finish the Internet configuration, please click SAVE to make the settings take effect. 4.3.2 LAN Choose “Interface Setup→LAN” menu, and you will see the LAN screen.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-7 Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. IP Address: Enter the modem router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Direction: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL modem router will periodically send routing information and accept routing information, and then incorporate them into routing table. IN only means the ADSL modem router will only accept but will not send RIP packet. OUT only means the ADSL modem router will only send but will not accept RIP packet.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Starting IP Address: Enter the starting IP address for the DHCP server's IP assignment. Because the default IP address for the modem router is 192.168.1.1, the default Start IP Address is 192.168.1.100. IP Pool Count: The max user pool size. Lease Time: The length of time for the IP lease. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 259200 seconds.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Hostname: Display the name of the DHCP client. IP Address: Display the IP Address of the DHCP client. MAC Address: Display the MAC Address of the DHCP client. Status: Display the status of the assigned IP Address, either Static or Auto. Static indicates that the IP Address is bounded to the MAC Address, while Auto indicates that the IP Address is assigned to the MAC Address automatically.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: If you select Disabled, the DHCP function will not take effect. 4.3.3 Wireless Choose “Interface Setup→Wireless” menu, and you will see the Wireless screen. Please configure the parameters for wireless according to the descriptions below.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-8 31
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Access point Settings: These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network. Access point: Select Activated to allow wireless station to associate with the access point. Channel: Select the channel you want to use from the drop-down List of Channel. This field determines which operating frequency will be used.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide 11n Settings: These are the settings of the 11n parameters. If “802.11n”, “802.11g+n” or “802.11b+g+n” is selected for Wireless mode, these settings will be displayed. Channel Bandwidth: Select the Bandwidth you want to use from the drop-down List. There are two options, “20 MHz” and “20/40 MHz”. If bigger bandwidth is selected, device could transmit and receive data with higher speed.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Method One: Enter the PIN into my modem router Step 1: For the configuration of the wireless adapter, please choose “Enter the PIN of this device into my access point or wireless router” in the configuration utility, and get the PIN code on the screen as below, then click Connect.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Method Two: Enter the PIN from your Router or AP device Step 1: Get the Current PIN code of your modem router from AP self PIN code (each modem router has its unique PIN code. Here takes the PIN code 11930624 of this modem router for example).
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Note: The default PIN code of the modem router can be found in its label or the WPS screen in its web configuration page. 2) PBC If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods. Select PBC, you will see the following screen.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide LAN LAN LAN LAN Step 2: Press and hold the WPS button of the adapter directly for about 2 seconds. Step 3: Wait until the following screen appears. Click OK to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter Method Two: Step 1: Press the WPS/RESET button on your modem router for about 2 seconds or click Start WPS button on the screen.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Step 3: Wait for a while until the following screen appears. Click OK to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter WPS progress: Show the current WPS progress. Reset to OOB: Reset WPS AP to the OOB(out-of-box) configuration. SSID: Wireless network name shared among all points in a wireless network.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide are: Disabled, WEP-64Bits, WEP-128Bits, WPA-PSK, WPA2-PSK, and WPA-PSK/ WPA2-PSK. 1) WEP- 64Bits To configure WEP-64Bits settings, select the WEP-64Bits option from the drop-down list. The menu will change to offer the appropriate settings. WEP-64Bits is a data privacy mechanism based on a 64-bit shared key algorithm, as described in the IEEE 802.11g standard.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Wireless MAC Address Filter: Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s RADIUS. Active: If you wish to filter users by MAC Address, select “Activated”, and “Deactived” for don’t. Action: To filter wireless users by MAC Address, select “Allow Association” or “Deny Association” the follow Wireless LAN station(s) association.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-10 6rd IPv6 Prefix: Enter the prefix of the IPv6. IPv4 Mask Length: The length of the selected WAN connection’s IPv4 mask. 6RD Border Relay IPv4Addr: The IPv4 address of the border relay router of 6RD tunnel. Use PVC: Select the PVC from the drop-down list. Note: To enable the function, there should not be any IPv6 WAN connections. 4.3.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Guest SSID: The guest network name. When setting up a Guest network, it is strongly recommended to use a name that easily distinguishes it from your primary network. Authentication Type: Select the Authentication Type from the drop-down list. Encryption: You can select either AES or AES+TKIP. Wireless Password: You may personalize your guest network password by entering a new password.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-13 Firewall: Select this option can automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack. SPI: If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side. 4.4.2 Routing Choose “Advanced Setup→Routing” menu, and you will see the routing information in the following screen.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Destination IP Address: This parameter specifies the IP network address of the final destination. IP Subnet Mask: Enter the subnet mask for this destination. Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL modem router that will forward the packet to the destination.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.3.1 DMZ Choose “Advanced Setup→NAT→DMZ”, you can configure the DMZ host in the following screen. A DMZ (demilitarized zone) is a host between a private local network and the outside public network. It prevents outside users from getting direct access to a server that has company data. Users of the public network outside the company can access to the DMZ host.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Local IP Address: Enter the IP Address for the Virtual Server in LAN side. Virtual Server Listing: This displays the information about the Virtual Servers you establish. To add a virtual server entry: Step 1: Select the “Virtual Circuit” and select “Virtual Server”. Note: For VCs with single IP, select Single; For VCs with multiple IPs, select Multiple for the option. Step 2: Select the Rule index for the rule.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Public Start & End IP: Enter the public IP Address you want to do NAT. Public Start IP is the starting public IP address and Public End IP is the ending public IP address. If you have a dynamic IP, enter 0.0.0.0 as the Public Start IP. Address Mapping List: This displays the information about the Mapping addresses. To add a mapping rule: Step 1: Select the “Virtual Circuit” and Multiple for the “Number of IPs”.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-18 IP Version：Select your IP version. QoS: Select this option to Activate/Deactivate the IP QoS on different types (IP ToS and DiffServ). Summary: Click the button to view the configurations of QoS. Rule: Configure the rules for QoS. If the traffic complies with the rule, then the modem router will take the corresponding action to deal with it. Rule Index: Select the index for the rule you want to configure.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Destination MAC & IP & Mask & Port Range: Enter the IP information about the Destination host for the rule. Source MAC & IP & Mask & Port Range: Enter the IP information about the Source host for the rule. Protocol ID: Select one among TCP/UDP, TCP, UDP or ICMP protocols for the application. Vlan ID Range: Enter the Vlan range, and the rule will be effective to the selected Vlans.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-19 1) Define VLAN Group Click Define VLAN Group, you can define VLAN groups in the following screen. VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum. VLAN ID: This indicates the VLAN group. ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the VC.
TD-W8961N 2) 300Mbps Wireless N ADSL2+ Modem Router User Guide Assign VLAN PVID for each Interface Click Assign VLAN PVID for each Interface, you can assign the PVID for each interface in the following screen. PVID: Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port. 4.4.6 ADSL Choose “Advanced Setup→ADSL”, you can select the ADSL Type and ADSL Mode in the following screen.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-20 ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ADSL Type: Select the ADSL operation type which your ADSL connection uses. 4.5 Access Management Choose “Access Management”, you can see the following submenus: Figure 4-21 Click any of them, and you will be able to configure the corresponding function. 4.5.1 ACL Choose “Access Management→ACL”, you can see the following screen.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-22 ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the modem router. If Deactivated, all IP addresses can access to the modem router. ACL Rule Index: Select the ACL rule index for the entry. Active: Enable the ACL rule. Secure IP Address: Select the IP addresses which are permitted to access to the modem router remotely. With the default IP 0.0.0.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-23 Filter Type Selection: Select the filter type for the configuration below. IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes. Interface: Select the interface for the entry. Note: If select PVC0~PVC7 as an interface, the filter will match the IP traffic of WAN port with specified IPs (Source IP Address and Destination IP Address).
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: Incoming means that IP traffic which is coming into the modem router, and the Outgoing means that IP traffic which is going out the modem router. IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry. Note: You should set the IP/MAC Filter Set Index and IP/MAC Filter Rule Index together to appoint the address (shown in the Filter List) for the IP Filter rule.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the Source IP Address, Destination IP Address, Subnet Mask and Port Number in the corresponding field. Step 4: Select the Protocol as “TCP” and select the Unmatched rule as “Next”. Step 5: Finally, click the SAVE to save the entry. Step 6: Go to Step 2 to configure the next two rules: Block E-mail received by the IP address 192.168.1.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule, and then click the DELETE button to delete the entry. 4.5.2.2 MAC Filter Select IP/MAC Filter as the Filter type, and select MAC as the Rule type, and then you can configure the filter rules based on MAC address. Figure 4-24 Rule Type: Select MAC for the MAC Filter rule. Active: Select “Yes” to make the rule to take effect.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide For example: If you want to block the PCs with MAC addresses 00:0A:EB:00:07:BE and 00:0A:EB:00:07:5F to access the Internet, you can configure as follows. Presume the rules are both aimed at the interface PVC0, and their indexes are (1, 1) and (1, 2). Step 1: Select the “IP/MAC Filter” as the Filter Type Selection: Select the “MAC” as the Rule Type on the Filter screen (show in Figure 4-24).
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.2.3 Application Filter Select Application Filter as the Filter type, and then you can configure the filter rules based on application. Figure 4-25 Filter Type Selection: Select the Application Filter for the next configuration. Application Filter: Activate or deactivate the function. ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Filter Type Selection: Select the URL Filter for the next configuration. Active: Select “Yes” to make the rule to take effect. URL Index: Select the index for the URL Filter entry. URL: Enter the URL for this URL Filter. URL Filter Listing: This displays the information about the URL Filter rules. To add a URL filter entry: For example: If you want to forbid the user to access the website: www.yahoo.com.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.3 SNMP Choose “Access Management→SNMP”, you can see the SNMP screen. The Simple Network Management Protocol (SNMP) is used for exchanging information between network devices. Figure 4-26 Get Community: Set the password for the incoming Get and Get next requests from the management station. Set Community: Set the password for incoming Set requests from the management station. 4.5.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Auto-Configure: If you activate the function, then the UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions. 4.5.5 DDNS Choose “Access Management→DDNS”, you can configure the DDNS function in the screen. The modem router offers a Dynamic Domain Name System (DDNS) feature.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-29 CWMP: Select activate the CWMP function. URL: Enter the website of ACS which is provided by your ISP. User Name/Password: Enter the User Name and password to login the ACS server. Path: Enter the path that connects to the ACS server. Port: Enter the port that connects to the ACS server. User Name/Password: Enter the User Name and Password that provided the ACS server to login the modem router.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-31 Note: 1) 2) There is only one account that can access Web-Management interface. The default account is "admin", and the password is "admin". Admin has read/write access privilege. When you change the password, you should enter the new password twice, and then click SAVE to make the new password take effect. 4.6.2 Time Zone Choose “Maintenance→Time Zone”, you can configure the system time in the screen.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Note: The ADSL modem router built-in some NTP Servers, when the modem router connects to the Internet, the modem router will get the system time automatically from the NTP Server. You can also configure the NTP Server address manually, and then the modem router will get the time from the specific Server firstly. 2) PC’s Clock Select PC’s Clock as the Synchronize time, you don’t need to set any items.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide computer. Click Browse to find the local hard drive and locate the firmware or romfile to be used for upgrade. Figure 4-35 To upgrade the modem router's firmware, follow these instructions below: Step 1: Type the path and file name of the update file into the “New Firmware Location” field. Or click the Browse button to locate the update file. Step 2: Click the UPGRADE button.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 2: Save the file as the appointed file. To restore the modem router’s settings: Step 1: Click the Browse button to locate the update file for the device, or enter the exact path in “New Romfile Location” field. Step 2: Click the UPGRADE button to complete. 4.6.4 SysRestart Choose “Maintenance→SysRestart”, you can select to restart the device with current settings or restore to factory default settings in the screen.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-36 4.6.5 Diagnostics Choose “Maintenance→Diagnostics”, you can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in the screen. Figure 4-37 4.7 Help Choose “Help”, you can view the help information for configuration of any function.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-38 Note: Click the tab, and you will be able to get the corresponding information.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A: Specifications General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5, Standards and Protocols IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary. 1. Configure TCP/IP component 1) On the Windows taskbar, click the Start button, and then click Control Panel.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure B-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure B-3 Note: For Windows 98 OS or before, the PC and Router may need to be restarted. Setting IP address manually 1 Select Use the following IP address radio button. And the following items available 2 If the modem router's LAN IP address is 192.168.1.1, specify the IP address as 192.168.1.x (x is from 2 to 254), and the Subnet mask as 255.255.255.0. 3 Type the modem router’s LAN IP address (the default IP is 192.168.1.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Figure B-4 Now: Click OK to keep your settings.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix C: Troubleshooting T1. What can I do if I don’t know or forget my password? 1) For default wireless password: Please refer to the “Wireless Password/PIN” labeled on the bottom of the modem router. 2) For the web management page password: Reset the modem router first and then use the default user name and password: admin/admin. T2.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide k) Right-click Wireless Network Connection (or Local Area Connection), and then click Properties. l) Select Internet Protocol (TCP/IP), and then click Properties. m) Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. For Windows 8 n) Move your mouse to the lower right corner and you will see Search icon in the Popups. Go to “ -> Apps”.
TD-W8961N 300Mbps Wireless N ADSL2+ Modem Router User Guide Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your modem router’s factory default settings and reconfigure your modem router following the instructions in Chapter 3 Quick Installation Guide. Please feel free to contact our Technical Support if the problem still exists. T4.
