910011428 REV 1.0.
Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright ©2015 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.
Contents Appearance .......................................................................1 LED Explanation ...................................................................... 1 Button and Port Explanation .................................................... 2 Positioning the Extender .......................................................... 2 Connect the Extender to the Internet .................................3 Before You Begin .....................................................................
RE Button LED This chapter covers the following topics: LED Explanation Button and Port Explanation Positioning the Extender Ethernet Port Statue RESET Color Green On Orange Red Blinking Green Off -- Indication The extender is connected to the router, and is in a good location. The extender is connected to the router, but is too far away from the router. No active connection. WPS connection is in progress, or the extender is initializing. The extender is powered off.
(Range Extender/WPS) Button: If your Wireless router supports WPS function, you can press the WPS button and then press the RE button of the extender to establish a secure connection between the wireless router and the extender. For safety consideration, we suggest you plug the extender right way up or upside down, as the pictures shown below. RESET: This button is used to restore the extender’s factory default settings.
Please read this chapter carefully before using the device. The operating distance range of your wireless connection can vary significantly depending on the physical position of the wireless devices. Factors that can weaken signals by getting in the way of your network’s radio waves are metal appliances or obstructions, and walls. Typical ranges vary based on the types of materials and background RF (radio frequency) noise in your home or office.
Place your extender in a well-ventilated place far from direct sunlight, any heater or heating vent. Leave at least 2 inches (5cm) space around the device for heat dissipation. Unplug your extender in a lighting storm to avoid damage. Use Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0 or above. Operating temperature of the extender should be 0℃~40℃ (32℉~104℉). Operating humidity of the extender should be 10%~90%RH (Noncondensing).
Immediately press the blinking. button on your extender. The LED starts Enjoy! The extender shares the same wireless network name (SSID) and wireless password as your router. If the LED does not turn solid green (or orange), please use Option Two: Using Web Browser. Some ISP gateways disable the WPS function by default, if the WPS method fails, please use Option Two: Using Web Browser.
● Via Ethernet Cable Disable the Wi-Fi on your computer. Connect the extender to your computer via an Ethernet cable. Connect to the Extender ● Via Wireless Disconnect the Ethernet (wired) connection to your computer. Click the Wi-Fi icon on the taskbar and connect to the extender's network (e.g. TP-LINK_Extender_XXXXXX). Configure Launch a web browser on your computer and type http://tplinkrepeater.net into the URL field, and use admin (all lowercase) for both username and password to log in.
Create a new username and password to log in the web management page, then click Confirm. Select your region and time zone, then click Next Per FCC regulations, all Wi-Fi products marketed in the U.S. are fixed to the U.S. region.
Select your router's 2.4GHz host network and enter the password, then click Next. Either copy the host’s SSID or customize it for the extended 2.4GHz network, then click Next. Verify your wireless settings and click Save. The LED should turn solid green, indicating successful connection. Relocate Plug the extender into an electrical outlet about halfway between your router (Host Network) and the Wi-Fi dead zone. Wait about 1 minute until the LED is lit with a solid green.
Enjoy! The extended network shares the same Wi-Fi password as your host network, but may have different wireless network name if you customize the name during the configuration. The extender can be used as an access point, thus to transform your existing wired network to a wireless network. Connect the extender to your router The extender can be used as a wireless adapter to connect any Ethernetenabled device, such as a Blu-ray player, game console, DVR, or smart TV, to your wireless network.
Change the SSID and Password (Optional) Go to Settings > Wireless > Wireless Settings page, configure the extender as the picture shows below, and click Save. Network Name (SSID): Set a SSID for your AP’s wireless network. Security: Select the security type. WPA/WPA2 - Personal is recommended. If WPA/WPA2 – Personal is selected, Select the security version. WPA2-PSK is recommended.
Select the encryption type. TKIP is NOT recommended if the extender operates in 802.11n mode, because TKIP is not supported by the 802.11n specification and the WPS function. Enter a new password in the Password field. If WEP is selected, network. Channel: Select the operating channel for the wireless network. It is recommended to leave the channel to Auto, if you are not experiencing the intermittent wireless connection issue.
Immediately push the WPS button on your client device. “Connect successfully” will appear on the WPS page, which means that your client device has connected to the AP by WPS. Method TWO: Enter the client’s PIN code on the AP Use this method if your client device has a WPS PIN code. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > Wireless > WPS page. Enable the WPS function of the AP.
On your client device, enter the AP’s PIN code. When the AP (extender)’s LED is solid on, the client device has successfully connected to the AP.
Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > Status page. You can view the network connection status in this page. ● The normal status. ● The extender is failed to connect to the wireless network of your router. This chapter covers the following topics: Current Status of the Extender Information about the Host Network, the Extender and the Clients ● ● The extender is connected to your router, but no transmitting data. Please check your host network.
● The extender is failed to connect to the NTP server, or obtain the DNS server address. Please check your host network. 1. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > Status page. Instructions The wireless is on and encrypted. 2. Click the icons of your router, the extender and clients. The detailed informations of the corresponding icon are displayed below. The wireless is on and unencrypted. Router：The wireless is off, or the connection is failed.
If you want to extend another network, you can refer to the following steps to finish it quickly. 1. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > Wireless > Connect to Network page. 2. Enable Connect to 2.4GHz Network. Then click Wireless Scanner to scan the wireless network you want to extend.
3. Select the network you want to extend from the list. 4. Once a network is selected, the SSID and security settings of that network will automatically be filled in. If the host network is encrypted, enter the password and click Save. When Host 2.4GHz Security is WEP, please select the index same as the host network. 5. Relocate If the network you want to extend is on but not shown in the list, please try the steps below. Move the extender closer to your router.
Secure the Extended Network On the Extended Network page, you can change and hide the wireless network name (SSID) of the extender, as well as enable or disable the wireless network of the extender. 1. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > Wireless > Extended Network page. 2. Either click Copy Host SSID or create a new name using up to 32 Change your Admin Account 1. Launch a web browser and log into http://tplinkrepeater.
select them and click Block to add them at the same time. Block / Allow Network Access from Specific Clients For increased security, you can restrict access to the extended network by allowing only specific wireless devices in the pre-set white list, or preventing the devices in the pre-set black list, from connecting to the extended network. Blacklist Mode The devices in the Blacklist are not allowed to connect to the extender. 1. Launch a web browser and log into http://tplinkrepeater.
Whitelist Mode Only the devices in the Whitelist are allowed to connect to the extender. 1. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > Advanced Settings > Access Control page. 2. Click the button to enable the Access Control function. 3. Select Whitelist as default access mode, then click Save. 4. Click Add to add a device manually into the whitelist. (2) Enter the Device Name. (3) Enter the device’s MAC Address. (4) Select the type of Effective Time.
Modify or Remove a Device in the Blacklist/Whitelist Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > Advanced Settings > Access Control page. In the Devices in Blacklist / Whitelist part: ● ● Click the icon address. , and then you can modify the device name and mac Click the icon to remove one device from the list. For several devices, select them and click Delete to remove them at the same time.
Settings > Network page. 2. Select Use the following IP address, then enter the IP address and gateway manually. Change the Extender’s IP Address By default, the extender is set to obtain an IP address automatically from the front router. If you want to use a specific IP address appropriate to your network demand, please refer to the steps below. IP Address: Enter the IP address in dotted-decimal notation (192.168.0.254 by default).
DHCP Server The extender can be configured as a DHCP (Dynamic Host Configuration Protocol) server to assign IP addresses automatically to the clients on the LAN. 1. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > Network page. automatically be turn on or off according to the DHCP settings of the host network. ● If you select on, please configure it manually.
Client Name: The name of the DHCP client. MAC Address: The MAC address of the DHCP client. Assigned IP Address: The IP address that is assigned to the client by the DHCP server. Lease Time: The time duration that the IP address is leased to the DHCP client. Click Refresh to refresh the DHCP Client List.
For power-saving purpose, you can power off the extender according to the preset time schedule by enabling this power schedule function. 1. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > Advanced Settings > Power Schedule page. 2.
The extender obtain the current time from the Internet automatically. You can set the time zone of your location via the Time Settings page. 1. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > System Tools > Time Settings page. 2. Select the Time Zone of your location, then click Save. (1) Select Enable Daylight Saving Time to enable this function. (2) Select the correct Start date and time when daylight saving time starts at your local time zone.
4. Click Save to save your settings. 4. Click Upgrade. The upgrade takes a few minutes to complete and the extender will automatically reboot itself when finished. Please DO NOT power off the extender during the upgrade process. 1. On your computer, download the latest firmware file from our support page at http://tp-link.com. 2. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > System Tools > Firmware Upgrade page. 3.
1. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > System Tools > Backup & Restore page. 2. Click Factory Restore to reset your extender to its factory default Please DO NOT power off the extender during the backup process. settings. Launch a web browser and log into http://tplinkrepeater.net, then go to Settings > System Tools > Backup & Restore page. Click Browse to select your backup file. And then click Restore restore the extender.
level. 3. Click Save Log to save all the logs in txt file to your computer. 1. Launch a web browser and log into http://tplinkrepeater.net. 2. Click Reboot on the top right corner to reboot the extender. If you have logged into the web management page http://tplinkrepeater.net, click Logout in the top right corner to log out safely.
This chapter covers the following topics: Factory Default Settings Troubleshooting Specifications Glossary Name Status Username admin Password admin IP Address 192.168.0.254 Subnet Mask 255.255.255.0 Domain http://tplinkrepeater.net SSID TP-LINK_Extender_XXXXXX Wireless Security Disabled Access Control Disabled T1.
● Option Two: Log into the extender's web management page, and go to System Tools > Restore & Backup page, click Factory Restore. Once the extender is reset, the current configurations will be erasered and you need to reconfigure it. When a device connects through the extender to your router, the MAC address of the device shown on the router is translated to another MAC address.
can obtain an IP address from your target wireless network and thus access the Internet, either via TL-WA855RE or without. T6. Will the extender work if I connect the ETHERNET port of it to the router via Ethernet cable? Sorry, it won’t work. The extender is designed to connect wirelessly to the router, while the ETHERNET port is designed to connect with a wired device, like Internet TV, Gaming console, DVR and so on. T7.
packet that can be transmitted. ● ● ● ● ● ● ● ● ● 802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.
"passphrase" as with WEP. But, using TKIP, WPA-Personal automatically changes the keys at a preset time interval, making it much more difficult for hackers to find and exploit them. The Wi-Fi Alliance will call this, WPAPersonal.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
restriction on installation height only for purposes of gathering telemetry information for automated monitoring and resources accounting systems. Permitted to use SRD for other purposes for outdoor applications only when the installation height is not exceeding 10 m above the ground surface. This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions: This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : Complies with the Canadian ICES-003 Class B specifications.
安全諮詢及注意事項 ● ● ● ● ● 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行 清潔。 ● 注意防潮，請勿將水或其他液體潑灑到本產品上。 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞 或覆蓋開口。 ● 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在 密閉位置中。 ● ● 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進 行此項工作。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
RECYCLING Symbal Explanation Class II equipment AC voltage This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
TP-LINK TECHNOLOGIES CO., LTD The product carries the CE Mark: For the following equipment: Product Description: 300Mbps Mini Wi-Fi Range Extender Model No.
