TL-WN353G 54M Wireless PCI Adapter
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2007 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Package Contents The following contents should be found in your box: ¾ ¾ ¾ One TL-WN353G 54M Wireless PCI Adapter Quick Installation Guide One Resource CD for TL-WN353G, including: • • • TP-LINK Wireless Utility and Drivers User Guide Other Helpful Information ) Note: If any of the listed contents are damaged or missing, please contact the retailer from whom you purchased the TL-WN353G 54M Wireless PCI Adapter for assistance.
COMMENT Chapter 1. Introduction ........................................................................................ 1 1.1 Overview of the product .............................................................................................. 1 1.2 Features ...................................................................................................................... 1 1.3 LED Status ............................................................................................................
TL-WN353G 54M Wireless PCI Adapter User Guide Chapter 1. Introduction 1.1 Overview of the product The TP-LINK TL-WN353G 54M Wireless PCI Adapter will provide you the flexibility to install your PC in the most convenient location available, without the cost of running network cables.
TL-WN353G 54M Wireless PCI Adapter User Guide Chapter 2. Installation Guide 2.1 Hardware Installation To install the Adapter, follow these steps listed below: 1. Turn off your desktop PC and disconnect the power. 2. Open your PC case and locate an available PCI slot on the motherboard. Remove the metal slot cover on the back of the PC. Check with your computer manufacturer for instructions if needed. 3. Slide the PCI Adapter into the PCI slot.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 2-1 Step 2: Click Next in the screen below (shown in Figure 2-2) to continue, you can click Cancel to end the installation. Figure 2-2 Step 3: After that, the files will be copied as the next screen shown (shown in Figure 2-3). To end the Installation, click Cancel.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 2-3 ) Note: During the installation, the system will warn about Windows Logo testing, please click Continue Anyway to continue the installation. Figure 2-4 Step 4: Click the Finish button to complete.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 2-5 2.2.3 Software Installation for Windows Vista Step 1: Insert the Resource CD into your CD-ROM drive, Click the Start button and choose Run. In the field that appears, enter F:\XXX\setup.exe (if "F" is the letter of your CD-ROM drive, XXX represents the setup program path, which is labeled on the Resource CD), then Figure 2-6 will appear; Click Cancel to end the installation in the screen. Otherwise, the installation will continue.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 2-6 Step 2: Click Next in the screen below (shown in Figure 2-2) to continue, you can click Cancel to end the installation. Figure 2-7 Step 3: After that, the files will be copied as the next screen shown (shown in Figure 2-3). To end the Installation, click Cancel.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 2-8 ) Note: During the installation, the system will warn about Windows Security testing, please click “Install this driver software anyway” to continue the installation. Figure 2-9 Step 4: Click the Finish button to complete.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 2-10 8
TL-WN353G 54M Wireless PCI Adapter User Guide Chapter 3. Configuration TP-LINK Wireless PCI Adapter TL-WN353G can be configured by TP-LINK Wireless Utility. This chapter describes how to configure your TP-LINK Wireless PCI Adapter for wireless connectivity on your Wireless Local Area Network (WLAN) and use the data security encryption features. After Installing the Adapter, the Adapter’s tray icon will appear in your system tray.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-1 Step 2: Click OK to continue. Figure 3-2 Step 3: After that, Select the network authentication and data encryption, then click OK.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-3 Step 4: Configure the IP information for the adapter. You can select “Obtain an IP address automatically” and “Obtain DNS server address automatically” to obtain an IP address. ) Note: If you want use the method, the AP that the adapter connects should support DHCP function.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-4 ) Note: You can also select “Use the following IP address” and “Use the following DNS server addresses” to assign the specific address. 3.2 General Status Choose the tab General as shown in Figure 3-5, the left filed displays the type of the adapter, the right field displays the status about the connection, including Status, Speed, Type, SSID, Signal Strength, Link Quality and other IP information.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-5 ¾ Signal Strength - This shows the strength of the wireless signal. ¾ Link Quality - This shows the quality of the wireless connection. ¾ ReNew IP - Click the button to get the IP address from the AP. ¾ Show Tray Icon - Select the option to display the icon on the bottom of the desktop. Otherwise, you can see the two icons. ¾ Disable Adapter - If you select the option, the adapter can’t work.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-6 3.3.1 Add or Edit a Configuration Profile Click the button Add or Edit (you should select an existed profile first to edit it) on the screen above, you can configure the profile as shown in Figure 3-7. We add a new profile and configure it for example here.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-7 ¾ Profile Name - Please enter the Profile name which identifies the configuration profile. This name must be unique. Note that the profile names are not case-sensitive. ¾ Network Name (SSID) - Please enter the IEEE 802.11 wireless network name. This field has a maximum limit of 32 characters. ) Note: The Profile Name and Network Name are necessary for the profile, you must configure it.
TL-WN353G 54M Wireless PCI Adapter User Guide ) Note: 1) Select different authentications and data encryptions, the security configuration is different. 2) When you select channel manually, the available network authentication are Open System, Shared key and WPA-None. ¾ • ASCII - Select this option, you can enter any ASCII characters to compose the password. • PASSPHRASE - Select this option, you can enter the characters from 0~9 to compose the password.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-8 Step 1: Select the “Open System” as the Network Authentication. Step 2: Select the “WEP” as Data encryption. Step 3: Select the type for the password, you can select the ASCII or PASSPHRASE. For ASCII, you can enter any characters in the keyboard; For PASSPHRASE, you can enter the characters from 0 to 9. Step 4: Select “64 Bits” as the Key Length, then enter “0123456789” as the password value.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-9 Step 1: Select the “WPA-PSK” as the Network Authentication. Step 2: Select the “TKIP” as Data encryption. Step 3: Enter the Network key and confirm it. Step 4: Click the OK to save the configuration. 4. WAP2-PSK authentication When you select the WPA2-PSK as the authentication, the available data encryptions are TKIP and AES. Please select the one according your need.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-10 ) Note: Select different EAP types, the configuration are different. 6. WAP2 802.1x When you select the WPA 802.1x as the authentication, the available data encryptions are TKIP and AES. For the authentication, you should configure the 802.1x security. ) Note: The configuration for WPA2 802.1x and WPA 802.1x are similar, you can refer to WPA 802.1x authentication to configure it. 7. WEP 802.1x When you select the WEP 802.
TL-WN353G 54M Wireless PCI Adapter User Guide Step 2: Select the profile name in the Profiles List. Step 3: Click Remove. Figure 3-11 3.3.3 Duplicate a configuration file Follow the steps below to change the name of a configuration profile. Step 1: Go to the Profile tab (shown in Figure 3-11). Step 2: Select the profile name in the Profiles List. Step 3: Click Duplicate, and then enter the new name for the configuration profile. 3.3.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-12 Step 1: Click Refresh to refresh the list at any time. Step 2: Highlight a network name and click Add to Profile to connect to an available network. Fill in the Profile name and click OK to create the new configuration profile for that network. 3.5 Advanced Click the tab Advanced as shown in Figure 3-13 to make further advanced configuration.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-13 ¾ ¾ Power Save Mode - Select the power save mode. • None - Turns power saving off, thus powering up the Wireless PCI Adapter continuously for a short message response time. • Min - Normal mode uses max when retrieving a large number of packets, then switches back to power save mode after retrieving the packets. • Max - Selects max mode to let the access point buffer incoming messages for the Wireless PCI Adapter.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-14 3.7 Statistics Click the tab Statistics as shown in Figure 3-13 to view the traffic statistics about the connection. Click the Reset to refresh the information.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-15 3.8 Easy Config Click the tab Easy Config as shown in Figure 3-16 to configure the adapter.
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-16 3.8.1 Touch-Button Method Select the Touch-Button Method (shown in Figure 3-16), then click Start, you can connect to the wireless network quickly, follow the steps below (shown in Figure 3-17).
TL-WN353G 54M Wireless PCI Adapter User Guide Step 1: Click the Refresh button to update the wireless network (shown in Figure 3-17), and then select the network you want to connect. Click Next. Step 2: Finally, enter the profile name for the network. Click Ok to complete. 3.8.2 Question-Answer Method Select the Touch-Button Method (shown in Figure 3-16), then click Start, you can connect to the wireless network quickly, follow the steps below (shown in Figure 3-18).
TL-WN353G 54M Wireless PCI Adapter User Guide Figure 3-19 Step 5: Finally, enter the profile name for the network. Click Ok to complete.
TL-WN353G 54M Wireless PCI Adapter User Guide Appendix A: Specifications Normal Interface 32bit PCI Interface Standards IEEE802.11b; IEEE802.11g Operating System Windows 98, ME, 2000, 2003, XP, Vista, XP64 Transmission Distance Indoor up to 100m, outdoor up to 300m (Standard transmission distance, it is limited to the environment). Radio Data Rate 54/48/36/24/18/12/9/6Mbps or 11/5.5/2/1Mbps (Auto Rate Sensing) Modulation 1M DBPSK; 2M DQPSK; 5.
TL-WN353G 54M Wireless PCI Adapter User Guide Appendix B: Glossary ¾ 802.11b - The 802.11b standard specifies a wireless product networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. ¾ 802.
TL-WN353G 54M Wireless PCI Adapter User Guide ¾ SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. See also Wireless Network Name and ESSID.
TL-WN353G 54M Wireless PCI Adapter User Guide Appendix C: PSP Setting Step 1: Choose ＂Network Settings” Step 2: Choose ”Infrastructure Mode” Step 3: Establish a new connection , enter the name of this connection. (any is ok),we use TEST for example. Step 4: Select SCAN, and let PSP scan the nearer AP automatic，then choose the default network SSID WLAN_AP of TL-WN322G 54M Wireless USB Adapter. Step 5: ”WLAN Security Setting” If you haven’t set pass phrase. select the first ”None” .
TL-WN353G 54M Wireless PCI Adapter User Guide Step 7: In ＂IP Address Setting＂screen ,we select ＂Manual” Step 8: In ”Address Setting” screen, please set IP address Step 9: ”Proxy Server” select ”Do Not Use” Step 10: Select ”Test Connection” Step 11: Test network connection. After the configuration that was set above, we can connect to web successfully. Till now, we have finished the configuration of PSP mode.
TL-WN353G 54M Wireless PCI Adapter User Guide ) Note: If you didn’t startup WEP Encryption, any PSP could link in, and the wireless network won’t be protected by encryption key.
TL-WN353G 54M Wireless PCI Adapter User Guide Appendix D: Contact Information For help with the Installation or operation of the TP-LINK TL-WN353G 54M Wireless PCI Adapter, please contact us. http://www.tp-link.
