TL-WR845N 300Mbps Wireless N Router REV1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2016 TP-LINK TECHNOLOGIES CO., LTD.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé.
請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.
Explanation of the symbols on the product label Symbol Explanation DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N Router Model No.: TL-WR845N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directive 1999/5/EC, Directive 2011/65/EU, 2009/125/EC The above product is in conformity with the following standards or other normative documents EN 300328 V1.9.
CONTENTS Package Contents ................................................................................................................................. 1 Chapter 1. Introduction.......................................................................................................................... 2 1.1 Overview of the Router ......................................................................................................... 2 1.2 Main Features ..................................................
4.7.1 4.8 4.9 Wireless Settings .................................................................................................... 43 DHCP .................................................................................................................................. 44 4.8.1 DHCP Settings ........................................................................................................ 44 4.8.2 DHCP Clients List ...............................................................................
4.16.1 Comexe DDNS ....................................................................................................... 75 4.16.2 Dyndns DDNS ........................................................................................................ 76 4.16.3 No-ip.com DDNS .................................................................................................... 76 4.17 IPv6 Support ...................................................................................................................
TL-WR845N 300Mbps Wireless N Router Package Contents The following items should be found in your package: TL-WR845N 300Mbps Wireless N Router DC Power Adapter for TL-WR845N 300Mbps Wireless N Router Quick Installation Guide Ethernet Cable Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor.
TL-WR845N 300Mbps Wireless N Router Chapter 1. Introduction 1.1 Overview of the Router The TL-WR845N 300Mbps Wireless N Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP. The 300Mbps Wireless N Router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking performance. Incredible Speed The TL-WR845N 300Mbps Wireless N Router provides up to 300Mbps wireless connection with other 802.
TL-WR845N 300Mbps Wireless N Router One 10/100M Auto-Negotiation RJ45 WAN port, four 10/100M Auto-Negotiation RJ45 LAN ports, supporting Auto MDI/MDIX. Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security. Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet access. Supports Virtual Server, Special Application and DMZ host. Supports UPnP, Dynamic DNS, Static Routing.
TL-WR845N 300Mbps Wireless N Router The router’s LEDs are located on the front panel (View from left to right). Name (Power) (WLAN) (LAN 4-1) (WAN) (WPS) Status Indication Off Power is off. On The router has finished booting. Flash The router is booting or upgrading. Off The Wireless function is disabled. On The Wireless function is enabled. Off There is no device linked to the corresponding port. On There is a device linked to the corresponding port.
TL-WR845N 300Mbps Wireless N Router approximately 8 seconds. And then release the button and wait the router to reboot to its factory default settings. Wi-Fi/WPS: This button is used for both WPS and Reset function. To use the WPS function, press it for less than five seconds; to use the RESET function, press it for more than five seconds. Used as Wi-Fi button: Press this Wi-Fi/WPS button for more than 2 seconds to turn on or off the wireless function of your router.
TL-WR845N 300Mbps Wireless N Router Chapter 2. Connecting the Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet) One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the router is connected directly to the Ethernet.) PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors TCP/IP protocol on each PC Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari 2.
TL-WR845N 5. 300Mbps Wireless N Router Verify that the hardware connection is correct by checking these LEDs.
TL-WR845N 300Mbps Wireless N Router Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your 300Mbps Wireless N Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default domain name of the 300Mbps Wireless N Router is http://tplinkwifi.net, the default IP address is 192.168.0.1, and the default Subnet Mask is 255.255.255.0. These values can be changed as you desire.
TL-WR845N 300Mbps Wireless N Router If the result displayed is similar to the figure below, it means the connection between your PC and the router is failed. Please check the connection following these steps: 1. Is the connection between your PC and the router correct? Note: The 1/2/3/4 LEDs of LAN ports which you link to on the router and LEDs on your PC's adapter should be lit. 2. Is the TCP/IP configuration for your PC correct? Note: If the router's IP address is 192.168.0.
TL-WR845N 300Mbps Wireless N Router Note: If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict. Therefore, in order to verify the network connection between your PC and the router, you can open a command prompt, and type ping 192.168.1.1, and then press Enter. 3.
TL-WR845N 300Mbps Wireless N Router Note: The Router will automatically detect the Internet connection. If the Internet is available, the Router will direct you to step 5 Wireless settings; otherwise, you need to continue with step 3 to choose WAN Connection Type. 3. Click Next, and then WAN Connection Type page will appear, shown in the figure below.
TL-WR845N 4. 300Mbps Wireless N Router If you select Auto-Detect, the router will automatically detect the connection type your ISP provides. Make sure the cable is securely plugged into the Internet port before detection. The appropriate configuration page will be displayed when an active Internet service is successfully detected by the router. 1) If the connection type is Dynamic IP, there will appear the MAC Clone page (as shown in the figure below).
TL-WR845N 300Mbps Wireless N Router IP Address - This is the WAN IP address as seen by external users on the Internet (including your ISP). Enter the IP address into the field. Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually 255.255.255.0. Default Gateway - Enter the gateway IP address into the box if required. Primary DNS - Enter the DNS Server IP address into the box if required.
TL-WR845N 300Mbps Wireless N Router Check the radio button of Dynamic/Static IP to activate the secondary connection if your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network. 4) If the connection type is L2TP/Russian L2TP, the next screen will appear as shown in the figure below. Configure the following parameters and then click Next to continue. User Name and Password - Enter the User Name and Password provided by your ISP.
TL-WR845N 300Mbps Wireless N Router 5) If the connection type is PPTP/Russian PPTP, the next screen will appear as shown in the figure below. Configure the following parameters and then click Next to continue. User Name and Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP. Confirm Password - Re-enter the password provided by your ISP to ensure the Password you entered is correct.
TL-WR845N 300Mbps Wireless N Router Wireless Radio - Enable or disable the wireless radio. Wireless Network Name - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be TP-LINK_XXXX (XXXX indicates the last unique four numbers of each router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test.
TL-WR845N 300Mbps Wireless N Router Channel Width - Select any channel width from the pull-down list. The default setting is automatic, which can adjust the channel width for your clients automatically. Channel - This field determines which operating frequency will be used. The default channel is set to Auto, so the AP will choose the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
TL-WR845N 300Mbps Wireless N Router Chapter 4. Configuring the Router This chapter will show each Web page's key functions and the configuration way. 4.1 Login After your successful login, you will see the main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below.
TL-WR845N 4.2 300Mbps Wireless N Router Status The Status page provides the current status information about the router. All information is read-only. 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide. 4.4 WPS This section will guide you to add a new wireless device to an existing network quickly by WPS (Wi-Fi Protected Setup) function.
TL-WR845N a). 300Mbps Wireless N Router Choose menu “WPS”, and you will see the next screen (shown in the figure below ). WPS Status - Enable or disable the WPS function here. Current PIN - The current value of the router's PIN is displayed here. The default PIN of the router can be found in the label attached on the router. Restore PIN - Restore the PIN of the router to its default. Gen New PIN - Click this button, and then you can get a new random value for the router's PIN.
TL-WR845N 300Mbps Wireless N Router Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 4: When the WPS LED is on, the client device has successfully connected to the router. Step 5: Refer back to your client device or its documentation for further instructions. II.
TL-WR845N 300Mbps Wireless N Router Note: 1) The WPS LED on the router will light green for five minutes if the device has been successfully added to the network. 2) The WPS function cannot be configured if the Wireless Function of the router is disabled. Please make sure the Wireless Function is enabled before configuring the WPS. 4.5 Network There are three submenus under the Network menu: WAN, MAC Clone, and LAN. Click any of them, and you will be able to configure the corresponding function.
TL-WR845N 300Mbps Wireless N Router This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP.
TL-WR845N 300Mbps Wireless N Router Default Gateway - (Optional) Enter the gateway IP address in dotted-decimal notation provided by your ISP. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP. Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-decimal notation provided by your ISP. Click the Save button to save your settings. 3.
TL-WR845N 300Mbps Wireless N Router Dynamic IP - You can check this radio button to use Dynamic IP as the secondary connection to connect to the local area network provided by ISP. Static IP - You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP.
TL-WR845N 300Mbps Wireless N Router MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. Service Name/AC Name - The service name and AC (Access Concentrator) name, which should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.
TL-WR845N 300Mbps Wireless N Router User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Auth Server - Enter the authenticating server IP address or host name. Auth Domain - Type in the domain suffix server name based on your location. e.g. NSW / ACT - nsw.bigpond.net.au VIC / TAS / WA / SA / NT - vic.bigpond.net.au QLD - qld.bigpond.net.
TL-WR845N 300Mbps Wireless N Router Connect Automatically - The connection can be re-established automatically when it was down. Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The Internet connection can be disconnected automatically after a specified inactivity period and re-established when you attempt to access the Internet again.
TL-WR845N 300Mbps Wireless N Router User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time).
TL-WR845N 300Mbps Wireless N Router User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
TL-WR845N 300Mbps Wireless N Router enter the number of minutes you want to have elapsed before your Internet connection terminates. Connect Automatically - Connect automatically after the router is disconnected. To use this option, click the radio button. Connect Manually - You can configure the router to make it connect or disconnect manually.
TL-WR845N 300Mbps Wireless N Router Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here. WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XX-XX format(X is any hexadecimal digit). Your PC's MAC Address - This field displays the MAC address of the PC that is managing the router.
TL-WR845N 300Mbps Wireless N Router IP Address - Enter the IP address of your router or reset it in dotted-decimal notation (factory default: 192.168.0.1). Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask. IGMP Proxy - If you want to watch TV through IGMP, please Enable it. Note: 1. If you change the IP Address of LAN, you must use the new IP Address to login the router. 2.
TL-WR845N 300Mbps Wireless N Router Wireless Network Name - Enter a value of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be TP-LINK_XXXX (XXXX indicates the last unique four numbers of each router’s MAC address). This value is case-sensitive. For example, TEST is NOT the same as test. Mode - Select the desired mode.
TL-WR845N 300Mbps Wireless N Router Enable WDS Bridging - Check this box to enable WDS. With this function, the router can bridge two or more WLANs. If this checkbox is selected, you will have to set the following parameters as shown below. Make sure the following settings are correct SSID (to be bridged) - The SSID of the AP your router is going to connect to as a client. You can also use the search function to select the SSID to join.
TL-WR845N 300Mbps Wireless N Router Disable Security - If you do not want to use wireless security, select this check box, but it’s strongly recommended to choose one of the following modes to enable security. WPA/WPA2 - Personal (Recommended) - It’s the WPA/WPA2 authentication type based on pre-shared passphrase. • Version - you can choose the version of the WPA-PSK security on the drop-down list.
TL-WR845N 300Mbps Wireless N Router • Wireless Password - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. Be sure to click the Save button to save your settings on this page. WPA /WPA2 - Enterprise - It’s based on Radius Server. • Version - you can choose the version of the WPA security on the pull-down list.
TL-WR845N 300Mbps Wireless N Router WEP - It is based on the IEEE 802.11 standard. If you select this check box, you will find a notice in red as shown in the figure below. • Type - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can select Open System or Shared Key authentication type automatically based on the wireless station's capability and request. • WEP Key Format - Hexadecimal and ASCII formats are provided.
TL-WR845N 300Mbps Wireless N Router To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address - The wireless station's MAC address that you want to filter. Status - The status of this entry either Enabled or Disabled. Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button.
TL-WR845N 300Mbps Wireless N Router To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button. Click the Enable All button to make all entries enabled Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries Click the Next button to go to the next page Click the Previous button to return to the previous page.
TL-WR845N 4.6.4 300Mbps Wireless N Router Wireless Advanced Choose menu “Wireless > Wireless Advanced”, you can configure the advanced settings of your wireless network. Transmit Power - Here you can specify the transmit power of router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here.
TL-WR845N 300Mbps Wireless N Router Enable WMM - WMM function can guarantee the packets with high- priority messages being transmitted preferentially. It is strongly recommended enabled. Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time. Enabled AP Isolation - This function can isolate wireless stations on your network from each other. Wireless devices will be able to communicate with the router but not with each other.
TL-WR845N 4.7 300Mbps Wireless N Router Guest Network 4.7.1 Wireless Settings Choose menu “Guest Network > Wireless Settings”, you can configure the Guest Network Wireless Settings on the page as shown in the figure below. Allow Guest To Access My Local Network - If enabled, guests can communicate with hosts. Enable Guest Network Bandwidth Control - If enabled, the Guest Network Bandwidth Control rules will take effect.
TL-WR845N 300Mbps Wireless N Router Access Time - During this time the wireless stations could accessing the AP. Note: The range of bandwidth for Guest Network is calculated according to the setting of Bandwidth Control on the page “Bandwidth Control- > Control Settings”. 4.8 DHCP There are three submenus under the DHCP menu: DHCP Settings, DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. 4.8.
TL-WR845N 300Mbps Wireless N Router Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. Default Gateway - (Optional.
TL-WR845N 300Mbps Wireless N Router will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. MAC Address - The MAC address of the PC for which you want to reserve IP address. Assigned IP Address - The IP address of the router reserved. Status - The status of this entry either Enabled or Disabled. To Reserve IP addresses: 1. Click the Add New … button.
TL-WR845N 300Mbps Wireless N Router Click the Next button to go to the next page and Click the Previous button to return the previous page. 4.9 Forwarding There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. 4.9.1 Virtual Servers Choose menu “Forwarding > Virtual Servers”, you can view and add virtual servers in the next screen.
TL-WR845N 300Mbps Wireless N Router To set up a virtual server entry: 1. Click the Add New… button. (pop-up the page of Add or Modify a Virtual Server Entry) 2. Select the service you want to use from the Common Service Port list. If the Common Service Port list does not have the service that you want to use, type the number of the service port or service port range in the Service Port box. 3.
TL-WR845N 300Mbps Wireless N Router Note: If you set the service port of the virtual server as 80, you must set the Web management port on System Tools – > Remote Management page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. 4.9.2 Port Triggering Choose menu “Forwarding > Port Triggering”, you can view and add port triggering in the next screen.
TL-WR845N 300Mbps Wireless N Router To add a new rule, follow the steps below. 1. Click the Add New… button, the next screen will pop-up as shown in the figure below. 2. Select a common application from the Common Applications drop-down list, then the Trigger Port field and the Incoming Ports field will be automatically filled. If the Common Applications do not have the application you need, enter the Trigger Port and the Incoming Ports manually. 3.
TL-WR845N 3. 300Mbps Wireless N Router Incoming Port Range cannot overlap each other. 4.9.3 DMZ Choose menu “Forwarding > DMZ”, you can view and configure DMZ host in the screen.The DMZ host feature allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing. DMZ host forwards all the ports at the same time.
TL-WR845N 300Mbps Wireless N Router Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disable button. As allowing this may present a risk to security, this feature is enabled by default. Current UPnP Settings List - This table displays the current UPnP information. • App Description -The description provided by the application in the UPnP request • External Port - External port, which the router opened for the application.
TL-WR845N 300Mbps Wireless N Router 4.10.1 Basic Security Choose menu “Security > Basic Security”, you can configure the basic security in the screen as shown in the figure below. Firewall - A firewall protects your network from the outside world. Here you can enable or disable the router’s firewall. SPI Firewall - SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session.
TL-WR845N 300Mbps Wireless N Router the use of cryptographic security services. To allow IPSec tunnels to pass through the router, keep the default, Enabled. ALG - It is recommended to enable Application Layer Gateway (ALG) because ALG allows customized Network Address Translation (NAT) traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, TFTP, H323 etc.
TL-WR845N 300Mbps Wireless N Router Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics. The result of the statistics is used for analysis by SYN Flood, UDP Flood and ICMP-Flood. DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function.
TL-WR845N 300Mbps Wireless N Router 4.10.3 Local Management Choose menu “Security > Local Management”, you can configure the management rule in the screen as shown in the figure below. The management feature allows you to deny computers in LAN from accessing the router. By default, the radio button “All the PCs on the LAN are allowed to access the Router's Web-Based Utility” is checked.
TL-WR845N 300Mbps Wireless N Router Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router's default remote management web port number is 80. For greater security, you can change the remote management web port to a custom port by entering that number in the box provided. Choose a number between 1 and 65534 but do not use the number of any common service port.
TL-WR845N 300Mbps Wireless N Router Parental Control - Check Enable if you want this function to take effect, otherwise check Disable. MAC Address of Parental PC - In this field, enter the MAC address of the controlling PC, or you can make use of the Copy To Above button below. MAC Address of Your PC - This field displays the MAC address of the PC that is managing this router.
TL-WR845N 300Mbps Wireless N Router 6. In the Status field, you can select Enabled or Disabled to enable or disable your entry. 8. Click the Save button. Click the Enable All button to enable all the rules in the list. Click the Disable All button to disable all the rules in the list. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page.
TL-WR845N 300Mbps Wireless N Router Enter “Allow TP-LINK” in the Website Description field. Enter “www.tp-link.com” in the Allowed Domain Name field. Select “Schedule_1” you create just now from the Effective Time drop-down list. In Status field, select Enable. 4. Click Save to complete the settings. Then you will go back to the Parental Control Settings page and see the following list, as shown in the figure below. 4.
TL-WR845N 300Mbps Wireless N Router Enable Internet Access Control - Select the check box to enable the Internet Access Control function, so the Default Filter Policy can take effect. Rule Name - Here displays the name of the rule and this name is unique. Host - Here displays the host selected in the corresponding rule. Target - Here displays the target selected in the corresponding rule. Schedule - Here displays the schedule selected in the corresponding rule.
TL-WR845N 300Mbps Wireless N Router 7. In the Status field, select Enabled or Disabled to enable or disable your entry. 9. Click the Save button. Click the Enable All button to enable all the rules in the list. Click the Disable All button to disable all the rules in the list. Click the Delete All button to delete all the entries in the table. You can change the entry’s order as desired. Fore entries are before hind entries.
TL-WR845N In Schedule field, select Schedule_1. In Action field, select Allow. In Status field, select Enable. Click Save to complete the settings. 300Mbps Wireless N Router Then you will go back to the Access Control Rule Management page and see the following list. 4.12.2 Host Choose menu “Access Control > Host”, you can view and set a Host list in the screen as shown in the figure below. The host list is necessary for the Access Control Rule.
TL-WR845N 300Mbps Wireless N Router Click the Next button to go to the next page, or click the Previous button return to the previous page. For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA, you should first follow the settings below: 1. Click Add New... button on the page of Host Settings to enter the Add or Modify a Host Entry page. 2. In Mode field, select MAC Address from the drop-down list. 3.
TL-WR845N 300Mbps Wireless N Router Target Description - Here displays the description about the target and this description is unique. Information - The target can be IP address, port, or domain name. Modify - To modify or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New… button. 2. In Mode field, select IP Address or Domain Name. If you select IP Address, the screen shown as the figure below.
TL-WR845N 300Mbps Wireless N Router 1) In Target Description field, create a unique description for the target (e.g. Target_1). 2) In Domain Name field, enter the domain name, either the full name or the keywords (for example tp-link) in the blank. Any domain name with keywords in it will be blocked or allowed. You can enter 4 domain names. 3. Click the Save button. Click the Delete All button to delete all the entries in the table.
TL-WR845N 300Mbps Wireless N Router Schedule Description - Here displays the description of the schedule and this description is unique. Day - Here displays the day(s) in a week. Time - Here displays the time period in a day. Modify - Here you can edit or delete an existing schedule. To add a new schedule, follow the steps below. 1. Click Add New... button shown on the page of Schedule Settings and the next screen will pop-up as shown as the page of Advanced Schedule Settings. 2.
TL-WR845N 300Mbps Wireless N Router For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA to access www.tp-link.com only from 18:00 to 20:00 on Saturday and Sunday, you should first follow the settings below: 1. Click Add New... button on the page of Advanced Schedule Settings to enter the Advanced Schedule Settings page. 2. In Schedule Description field, create a unique description for the schedule (e.g. Schedule_1). 3.
TL-WR845N 300Mbps Wireless N Router 4.13.1 Static Routing List Choose menu “Advanced Routing > Static Routing List”, and then you can configure the static route in the next screen. A static route is a pre-determined path that network information must travel to reach a specific host or network. To add static routing entries: 1. Click Add New… on the page of Static Routing, you will see the screen in the figure below. 2.
TL-WR845N 300Mbps Wireless N Router Click the Enable All button to enable all the entries. Click the Disable All button to disable all the entries. Click the Delete All button to delete all the entries. Click the Previous button to view the information in the previous screen, click the Next button to view the information in the next screen. 4.13.2 System Routing Table Choose menu “Advanced Routing >System Routing Table”, and then you can view the System Routing Table in the next screen shown below.
TL-WR845N 300Mbps Wireless N Router There are two submenus under the Bandwidth Control menu. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.14.1 Control Settings Choose menu “Bandwidth Control > Control Settings”, you can configure the Egress Bandwidth and Ingress Bandwidth in the next screen. Their values you configure should be less than 100000Kbps.
TL-WR845N 300Mbps Wireless N Router Enable - This displays the status of the rule. Modify - Click Modify to edit the rule. Click Delete to delete the rule. To add/modify a Bandwidth Control rule, follow the steps below. Step 1: Click Add New… on the page of Bandwidth Control Rule List, you will see a new screen shown in the figure below. Step 2: Enter the information like the screen shown below. Step 3: Click the Save button. 4.
TL-WR845N 300Mbps Wireless N Router MAC Address - The MAC address of the controlled computer in the LAN. IP Address - The assigned IP address of the controlled computer in the LAN. Bind - Check this option to enable ARP binding for a specific device. Modify - To modify or delete an existing entry. When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Modify button, and then you will go to the next page.
TL-WR845N 3. 300Mbps Wireless N Router Click the Find button in the page as shown in the figure below. Click the Enable All button to make all entries enabled. Click the Delete All button to delete all entries. 4.15.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could configure the items on the ARP list also.
TL-WR845N 300Mbps Wireless N Router Note: An item could not be loaded to the IP & MAC Binding list if the IP address of the item has been loaded before. Error warning will prompt as well. Likewise, "Load All" only loads the items without interference to the IP & MAC Binding list. 4.16 Dynamic DNS Choose menu “Dynamic DNS”, and you can configure the Dynamic DNS function.
TL-WR845N 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service. 300Mbps Wireless N Router Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service. 4.16.2 Dyndns DDNS If the dynamic DNS Service Provider you select is dyn.com/dns, the page will appear as shown below. To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2.
TL-WR845N 300Mbps Wireless N Router To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider. 4. Click the Login button to log in the DDNS service. Connection Status - The status of the DDNS service connection is displayed here. Click Logout to log out the DDNS service. 4.
TL-WR845N 300Mbps Wireless N Router 4.17.1 IPv6 Status The IPv6 Status page displays the router's current IPv6 status and configuration. All information is read-only. WAN • Connection Type - The IPv6 connection way for WAN. • IPv6 Address - The WAN IPv6 address. • IPv6 Default Gateway - The router's default gateway. • Primary IPv6 DNS - The primary IPv6 DNS address. • Secondary IPv6 DNS - The secondary IPv6 DNS address.
TL-WR845N 300Mbps Wireless N Router 4.17.2 IPv6 Setup Enable IPv6 - Tick the checkbox to enable the IPv6 function. It’s enabled by default. WAN Connection Type - Choose the correct WAN connection type based on your ISP network topology. • SLAAC - Connections which use RADVD IPv6 address assignment. • DHCPv6 - Connections which use dynamic IPv6 address assignment. • Static IPv6 - Connections which use static IPv6 address assignment.
TL-WR845N 300Mbps Wireless N Router 1) SLAAC IPv6 Address - The IPv6 address assigned by your ISP dynamically. IPv6 Address Prefix - Display the IPv6 Prefix Length in dotted-decimal notation provided by your ISP. Default Gateway - Display the default gateway in colon-hexadecimal notation provided by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
TL-WR845N 300Mbps Wireless N Router Address Autoconfiguration Type - RADVD (Router Advertisement Daemon) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server. Site Prefix Configuration Type - The type of IPv6 address prefix. • Delegated - Get the IPv6 address prefix from the ISP automatically, and the device will delegate it to the LAN. • Static - Configure the Site Prefix and Site Prefix Length manually. Please contact your ISP to get more information before you configure them.
TL-WR845N 300Mbps Wireless N Router Primary IPv6 DNS - Enter the DNS IPv6 address in dotted-decimal notation provided by your ISP. Secondary IPv6 DNS - Enter another DNS IPv6 address in dotted-decimal notation provided by your ISP. Note: If you get Address not found error when you access a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.
TL-WR845N 300Mbps Wireless N Router MTU Size (in bytes) - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs, you may need to modify the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. Primary DNS - Enter the DNS IPv6 address in dotted-decimal notation provided by your ISP. Secondary DNS - Enter another DNS IPv6 address in dotted-decimal notation provided by your ISP.
TL-WR845N 4) 300Mbps Wireless N Router PPPoEv6 PPPoE Session - The PPP session type for IPv6 connection. There are two types: • Share with PPPoEv4 - The PPPoEv6 and PPPoEv4 use the same PPP session. • Create a new Session - The PPPoEv6 and PPPoEv4 use different PPP sessions. It is default to select this option. User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.
TL-WR845N 300Mbps Wireless N Router • Alway On - Connect automatically. • Connect Manual - Connect by the user manually. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Address Autoconfiguration Type - RADVD (Router Advertisement Daemon) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server. Site Prefix Configuration Type - The type of IPv6 address prefix.
TL-WR845N 300Mbps Wireless N Router MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1480 Bytes. For some ISPs, you may need to modify the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. If your ISP gives you one or two DNS IPv6 addresses, select Use the following IPv6 DNS Servers and enter the Primary IPv6 DNS and Secondary IPv6 DNS into the correct fields.
TL-WR845N 300Mbps Wireless N Router 4.18.1 Time Settings Choose menu “System Tools > Time Settings”, you can configure the time on the following screen. Time Zone - Select your local time zone from this drop-down list. Date - Enter your local date in MM/DD/YY into the right blanks. Time - Enter your local time in HH/MM/SS into the right blanks.
TL-WR845N 300Mbps Wireless N Router To set time automatically: 1. Select your local time zone. 2. Enter the address or domain of the NTP Server I or NTP Server II. 3. Click the Get GMT button to get system time from Internet if you have connected to the Internet. To set Daylight Saving: 1. Check the box to enable Daylight Saving. 2. Select the start time from the drop-down lists in the Start field. 3. Select the end time from the drop-down lists in the End field. 4.
TL-WR845N 300Mbps Wireless N Router Diagnostic Tool - Check the radio button to select one diagnostic too. Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Traceroute - This diagnostic tool tests the performance of a connection. Note: You can use ping/traceroute to test both numeric IP address or domain name.
TL-WR845N 300Mbps Wireless N Router The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Note: Only one user can use this tool at one time. Options “Number of Pings”, “Ping Size” and “Ping Timeout” are used for Ping function. Option “Tracert Hops” are used for Tracert function. 4.18.
TL-WR845N 300Mbps Wireless N Router 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the router rather than the configuration, you can try to upgrade the firmware. 2.
TL-WR845N 300Mbps Wireless N Router Click the Backup button to save all configuration settings as a backup file in your local computer. To upgrade the router's configuration, follow these instructions. • Click the Browse… button to locate the update file for the router, or enter the exact path to the Setting file in the text box. • Click the Restore button. Note: The current configuration will be covered by the uploading configuration file.
TL-WR845N 300Mbps Wireless N Router It is strongly recommended that you should change the factory default user name and password of the router, because all users who try to access the router's Web-based utility or Quick Setup will be prompted for the router's default user name and password. Note: The new user name and password must not exceed 14 characters in length and not include any spaces. Enter the new Password twice to confirm. Click the Save button when finished.
TL-WR845N 300Mbps Wireless N Router Auto Mail Feature - Indicates whether auto mail feature is enabled or not. Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature, as shown in the figure below. From - Your mail box address. The router would connect it to send logs. To - Recipient’s address. The destination mailbox where the logs would be received. SMTP Server - Your smtp server.
TL-WR845N 300Mbps Wireless N Router Log Type - By selecting the log type, only logs of this type will be shown. Log Level - By selecting the log level, only logs of this level will be shown. Refresh - Refresh the page to show the latest log list. Save Log - Click to save all the logs in a txt file. Mail Log - Click to send an email of current logs manually according to the address and validation information set in Mail Settings.
TL-WR845N IP/MAC Address Total Current Modify 300Mbps Wireless N Router The IP and MAC address are displayed with related statistics. Packets The total number of packets received and transmitted by the Router. Bytes The total number of bytes received and transmitted by the Router. Packets The total number of packets received and transmitted in the last Packets Statistic interval seconds. Bytes The total number of bytes received and transmitted in the last Packets Statistic interval seconds.
TL-WR845N 300Mbps Wireless N Router Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the router. The telephone cord plugs into the Line port of the ADSL Modem. 3) Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “PPPoE” for WAN Connection Type.
TL-WR845N 2. 300Mbps Wireless N Router How do I configure the router to access Internet by Ethernet users? 1) Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking “Save”. 2) Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem during installation.
TL-WR845N 300Mbps Wireless N Router Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page. 4) How to enable DMZ Host: Log in to the router, click the “Forwarding” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click Enable radio button and type your IP address into the “DMZ Host IP Address” field, using 192.168.0.198 as an example, remember to click the Save button.
TL-WR845N 4. 300Mbps Wireless N Router I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the router, you must change the WEB management port number to avoid interference. 2) To change the WEB management port number: Log in to the router, click the “Security” menu on the left of your browser, and click "Remote Management" submenu.
TL-WR845N 300Mbps Wireless N Router on the “Add or Modify a Virtual Server” page, enter “80” into the blank next to the “Service Port”, and your IP address next to the “IP Address”, assuming 192.168.0.188 for an example, remember to Enable and Save. 5. The wireless stations cannot connect to the router. 1) Make sure the "Wireless Router Radio" is enabled. 2) Make sure that the wireless stations' SSID accord with the router's SSID.
TL-WR845N 300Mbps Wireless N Router Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed. 1. Install TCP/IP component 1) On the Windows taskbar, click the Start button, and then click Control Panel. 2) Click the Network and Internet, and click the Network and Sharing Center, then click Change adapter settings.
TL-WR845N 5) 300Mbps Wireless N Router The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
TL-WR845N 300Mbps Wireless N Router Setting IP address manually 1 Select Use the following IP address radio button. And the following items available 2 If the router's LAN IP address is 192.168.0.1, specify the IP address as 192.168.0.x (x is from 2 to 254), and Subnet mask is 255.255.255.0. 3 Type the router’s LAN IP address (the default IP is 192.168.0.1) into the Default gateway field. 4 Select Use the following DNS server addresses radio button.
TL-WR845N -105- 300Mbps Wireless N Router
TL-WR845N 300Mbps Wireless N Router Appendix C: Specifications General Standards IEEE 802.3, 802.3u, 802.11b, 802.11g and 802.
TL-WR845N 300Mbps Wireless N Router Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802.
TL-WR845N 300Mbps Wireless N Router SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name.