User Guide 300Mbps Wireless N Router TL-WR845N REV3.0.
Contents About This Guide..........................................................................................................1 Chapter 1. Get to Know About Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 1. 1. 2. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. 7. 1.Virtual Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 4. 7. 2.Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 4. 7. 3. DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 4. 8. 4. 7. 4. UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About This Guide This guide is a complement to Quick Installation Guide. The Quick Installation Guide provides instructions for quick Internet setup, while this guide contains details of each function and demonstrates how to configure them. When using this guide, please notice that features of the router may vary slightly depending on the model and software version you have, and on your location, language, and Internet service provider.
Chapter 1 Get to Know About Your Router This chapter introduces what the router can do and shows its appearance.
Chapter 1 1. 1. Product Overview The TP-LINK router is designed to fully meet the need of Small Office/Home Office (SOHO) networks and users demanding higher networking performance. The powerful antennas ensure continuous Wi-Fi signal to all your devices while boosting widespread coverage throughout your home, and the built-in Ethernet ports supply high-speed connection to your wired devices.
Chapter 1 LED Explanation Name Status On (Power) (Wireless) (Ethernet) Flashing (WPS) 1. 2. 2. System initialization completes. System initialization or firmware upgrade is in prograss. Do not disconnect or power off the router. Off Power is off. On The wireless function is working properly. Off The wireless function is disabled. On The corresponding Ethernet port is connected. Off No Ethernet port is connected. Blue On (Internet) Indication Orange On Off The Internet is available.
Chapter 1 Item Description Power Port For connecting the router to a power socket via the provided power adapter. WAN Port For connecting to a DSL/Cable modem, or an Ethernet port. Ethernet Ports (1/2/3/4) For connecting your PCs or other wired network devices to the router. Press and hold this button until the WPS/Wi-Fi Button LED is on/off to turn on/off the Wi-Fi function. To enable the WPS function, press this button about 2 seconds.
Chapter 2 Connect the Hardware This chapter contains the following sections: • “Position Your Router” • “Connect Your Router”
Chapter 2 2. 1. Position Your Router • The product should not be located in a place where it will be exposed to moisture or excessive heat. • Place the router in a location where it can be connected to multiple devices as well as to a power source. • Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard. • The router can be placed on a shelf or desktop.
Chapter 2 4 ) Connect the power adapter to the router and turn on the router. 5 ) Verify that the hardware connection is correct by checking these LEDs. Power On Wi-Fi On Internet On Tips: If Wi-Fi LED is off, press and hold the WPS/Wi-Fi button until it is on. 2. Connect your computer to the router. • Method 1: Wired Turn off the Wi-Fi on your computer and connect the devices as shown below. Ethernet cable • Method 2: Wirelessly 1.
Chapter 2 Close to Reset WPS/ Wi-Fi 9
Chapter 3 Set Up Internet Connection Via Quick Setup Wizard This chapter introduces how to connect your router to the Internet via the web-based Quick Setup Wizard.
Chapter 3 3. 1. Log in to the Router With the web-based utility, it is easy to configure and manage the router. The webbased utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft the Internet Explorer, Mozilla Firefox or Apple Safari. Follow the steps below to log in to your router. 1. Set up the TCP/IP Protocol in Obtain an IP address automatically mode on your computer. 2. Visit http://tplinkwifi.
Chapter 3 2. In this case, we take dynamic IP for instance. Please select to clone the mac address or not and click Next. For other connection types, please enter the parameters provided by your ISP, and then click Next. 3. Either customize your Wireless Network Name and Wireless Password or keep the default ones, and then click Next.
Chapter 3 4. Click Finish to complete the configuration.
Chapter 4 Configure the router This chapter presents how to configure the various features of the router.
Chapter 4 4. 1. Status 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Status. You can view the current status information of the router. • Firmware Version - The version information of the router’s firmware. • Hardware Version - The version information of the router’s hardware. • LAN - This field displays the current settings of the LAN, and you can configure them on the Network > LAN page.
Chapter 4 • Name (SSID) - The SSID of the router. • Channel Width - The current wireless channel width in use. • • • • Mode - The current wireless working mode in use. Channel - The current wireless channel in use. MAC Address - The physical address of the router. WDS Status - The status of WDS connection. • WAN - This field displays the current settings of the WAN, and you can configure them on the Network > WAN page. • MAC Address - The physical address of the WAN port.
Chapter 4 Method ONE: Press the WPS Button on Your Client Device 1. Keep the WPS Status as Enabled and click Add Device. 2. Select Press the button of the new device in two minutes and click Connect. 3. Within two minutes, press the WPS button on your client device. 4. A success message will appear on the WPS page if the client device has been successfully added to the router’s network. Method TWO: Enter the Client’s PIN 1. Keep the WPS Status as Enabled and click Add Device. 2.
Chapter 4 3. A success message will appear on the WPS page if the client device has been successfully added to the router’s network. Method Three: Enter the Router’s PIN 1. Keep the WPS Status as Enabled and get the Current PIN of the router. 2. Enter the router’s current PIN on your client device to join the router’s Wi-Fi network. 4. 3. Network 4. 3. 1. WAN 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Network > WAN. 3.
Chapter 4 • MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU size unless required by your ISP. • Use These DNS Servers - If your ISP providess you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses. Otherwise, the DNS servers will be assigned dynamically from your ISP. • Host Name - This option specifies the name of the router.
Chapter 4 PPPoE/Russia PPPoE If your ISP provides PPPoE connection, select PPPoE/Russia PPPoE. • User Name/Password - Enter the user name and password provided by your ISP. These fields are case-sensitive. • Confirm Password - Enter the Password provided by your ISP again to ensure the password you entered is correct. • Secondary Connection - It’s available only for PPPoE connection. If your ISP provides an extra connection type, select Dynamic IP or Static IP to activate the secondary connection.
Chapter 4 Note: after a specified inactivity period (Max Idle Time) and not be able to re-establish when you attempt to access the Internet again. • Only when you have configured the system time on the System Tools > Time Settings page, will the time-based connecting function take effect. • Sometimes the connection cannot be terminated although you have specified the Max Idle Time because some applications are visiting the Internet continually in the background.
Chapter 4 • User Name/Password - Enter the user name and password provided by your ISP. These fields are case-sensitive. • Auth Server - Enter the authenticating server IP address or host name. • Auth Domain - Type in the domain suffix server name based on your location. • MTU Size - The default MTU size is 1480 bytes. It is not recommended that you change the default MTU size unless required by your ISP.
Chapter 4 L2TP/Russia L2TP If your ISP provides L2TP connection, please select L2TP/Russia L2TP. • User Name/Password - Enter the user name and password provided by your ISP. These fields are case-sensitive. • Confirm Password - Enter the Password provided by your ISP again to ensure the password you entered is correct. • Connect/Disconnect - Click this button to connect or disconnect immediately. • Dynamic IP/ Static IP - Select either as required by your ISP.
Chapter 4 • • field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects. Connect Automatically - The connection can be re-established automatically when it is down. Connect Manually - You can click Connect/Disconnect to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode.
Chapter 4 • Confirm Password - Enter the Password provided by your ISP again to ensure the password you entered is correct. • Connect/Disconnect - Click this button to connect or disconnect immediately. • Dynamic IP/ Static IP - Select either as required by your ISP. If Static IP is selected, please enter the IP address, subnet marsk, gateway and DNS also provided by your ISP. • Internet IP Address/ Internet DNS - The Internet IP address and DNS server address assigned by L2TP server.
Chapter 4 address in this field. Click Restore Factory MAC to restore the MAC address of WAN port to the factory default value. • Your PC’s MAC Address - This field displays the MAC address of the PC that is managing the router. If the MAC address is required, you can click Clone MAC Address and this MAC address will be filled in the WAN MAC Address field. Note: • You can only use the MAC Address Clone function for PCs on the LAN.
Chapter 4 2. Go to Wireless > Wireless Settings. 3. Configure the basic settings for the wireless network and click Save. • Wireless Network Name - Enter a string of up to 32 characters. The default SSID is TP-LINK_XXXX (XXXX indicates the last unique four numbers of each router’s MAC address). It is strongly recommended that you change your network name (SSID). This value is case-sensitive. For example, TEST is NOT the same as test. • Mode - Select the desired mode.
Chapter 4 Note: If this checkbox is selected, you had better make sure the following settings are correct. • SSID (to be bridged) - The SSID of the AP your router is going to connect to as a client. You can also use the survey function to select the SSID to join. • BSSID (to be bridged) - The BSSID of the AP your router is going to connect to as a client. You can also use the survey function to select the BSSID to join. • Survey - Click this button, you can search the AP which runs currently.
Chapter 4 • Disable Security - The wireless security function can be enabled or disabled. If disabled, wireless clients can connect to the router without a password. It’s strongly recommended to choose one of the following modes to enable security. • WPA-PSK/WPA2-Personal - It’s the WPA/WPA2 authentication type based on preshared passphrase. • Version - Select Automatic, WPA-PSK or WPA2-PSK. • Wireless Password - Enter ASCII or Hexadecimal characters.
Chapter 4 • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. • WEP - It is based on the IEEE 802.11 standard. • • • • • • • Type - The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless client’s capability and request. WEP Key Format - Hexadecimal and ASCII formats are provided here.
Chapter 4 4. Select Allow the stations specified by any enabled entries in the list to access as the filtering rule. 5. Delete or disable all entries if there are any entries already. 6. Click Add New and fill in the blanks. 1 ) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB00-07-5F in the MAC Address field. 2 ) Enter wireless client A/B in the Description field. 3 ) Leave the status as Enabled. 4 ) Click Save and click Back. 7.
Chapter 4 Note: If you are not familiar with the setting items on this page, it’s strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. • Transmit Power - Select High, Middle or Low which you would like to specify for the router. High is the default setting and recommended. • Beacon Interval - Enter a value between 40-1000 milliseconds for Beacon Interval here. Beacon Interval value determines the time interval of the beacons.
Chapter 4 • Enable AP Isolation - This function isolates all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS / Bridge is enabled. 4. 4. 5. Wireless Statistics 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Wireless > Wireless Statistics to check the data packets sent and received by each client device connected to the router.
Chapter 4 6. Select Schedule from the Access Time drop-down list and customize it for the guest network. 7. Click Save. • • • • • • • • Allow Guest To Access My Local Network - If enabled, guests can access the local network and manage it. Enable Guest Network Bandwidth Control - If enabled, the Guest Network Bandwidth Control rules will take effect. Egress Bandwidth For Guest Network - The upload speed through the WAN port for the guest network.
Chapter 4 4. 6. DHCP 4. 6. 1. DHCP Settings By default, the DHCP (Dynamic Host Configuration Protocol) Server is enabled and the router acts as a DHCP server; it dynamically assigns TCP/IP parameters to client devices from the IP Address Pool. You can change the settings of DHCP Server if necessary, and you can reserve LAN IP addresses for specified client devices. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to DHCP > DHCP Settings. 3.
Chapter 4 Note: To use the DHCP server function of the router, you must configure all computers on the LAN as Obtain an IP Address automatically. 4. 6. 2. DHCP Client List 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to DHCP > DHCP Client List to view the information of the clients connected to the router. • Client Name - The name of the DHCP client. • MAC Address - The MAC address of the DHCP client.
Chapter 4 3 ) Leave the status as Enabled. 4 ) Click Save. 4. 7. Forwarding The router’s NAT (Network Address Translation) feature makes the devices on the LAN use the same public IP address to communicate in the Internet, which protects the local network by hiding IP addresses of the devices. However, it also brings about the problem that external hosts cannot initiatively communicate with the specified devices in the local network.
Chapter 4 2. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 3. Go to Forwarding > Virtual Servers. 4. Click Add New. Select HTTP from the Common Service Port list. The service port, internal port and protocol will be automatically filled in. Enter the PC’s IP address 192.168.0.100 in the IP Address field. 5. Leave the status as Enabled and click Save.
Chapter 4 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Forwarding > Port Triggering. 3. Click Add New. Select the desired application from the Common Applications list. The trigger port amd incoming ports will be automatically filled in. The following picture takes application MSN Gaming Zone as an example. 4. Leave the status as Enabled and click Save. Note: • You can add multiple port triggering rules as needed.
Chapter 4 host with all ports opened. 1. Assign a static IP address to your PC, for example 192.168.0.100. How can I do that? 2. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 3. Go to Forwarding > DMZ. 4. Select Enable and enter the IP address 192.168.0.100 in the DMZ Host IP Address filed. 5. Click Save. Done! 4. 7. 4. You’ve set your PC to a DMZ host and now you can make a team to game with other players.
Chapter 4 If necessary, you can follow the steps to change the status of UPnP. 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Forwarding > UPnP. 3. Click Disable or Enable according to your needs. 4. 8. Security 4. 8. 1. Basic Security This function allows you to protect your home network from cyber attacks and unauthorized users by implementing these network security functions. 1. Visit http://tplinkwifi.
Chapter 4 • SPI Firewall - SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the traffic passing through the session conforms to the protocol. SPI Firewall is enabled by default. • VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using IPSec, PPTP or L2TP protocols to pass through the router’s firewall.
Chapter 4 • Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics. The result of the statistics is used for analysis by SYN Flood, UDP Flood and ICMP-Flood. • DoS Protection - Denial of Service protection. Select Enable or Disable to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled.
Chapter 4 • Ignore Ping Packet From WAN Port - The default setting is disabled. If enabled, the ping packet from the Internet cannot access the router. • Forbid Ping Packet From LAN Port - The default setting is disabled. If enabled, the ping packet from LAN cannot access the router. This function can be used to defend against some viruses. 3. Click Save. 4. Click Blocked DoS Host List to display the DoS host table by blocking. 4. 8. 3. Local Management 1. Visit http://tplinkwifi.
Chapter 4 4. 8. 4. Remote Management 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Security > Remote Management, and you can manage your router from a remote device via the Internet. • Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router’s default remote management web port number is 80.
Chapter 4 4. Go to Parental Control. 5. Select Enable and enter the MAC address 00-11-22-33-44-BB in the MAC Address of Parental PC field. 6. Click Add New. 7. Enter appropriate parameters in corresponding fields. • Enter 00-11-22-33-44-AA in the MAC Address of Children’s PC field. • • • Enter www.tp-link.com in the Allowed Website Name field. Select Schedule_1 you created from the Effective Time drop-down list. In the Status field, select Enable.
Chapter 4 4. 10. Access Control Access Control is used to deny or allow specific client devices to access your network with access time and content restrictions. I want to: How can I do that? Deny or allow specific client devices to access my network with access tiem and content restrictions. For example, If you want to restrict the Internet activities of host with MAC address 00-11-22-33-44-AA on the LAN to access www.tp-link.com only, please follow the steps below: 1. Visit http://tplinkwifi.
Chapter 4 3 ) Click Save. 4. Go to Access Control > Schedule and configure the schedule settings: 1 ) Click Add New. 2 ) Create a unique description (e.g. schedule_1) for the schedule in the Schedule Description field and set the day(s) and time period. 3 ) Click Save. 5. Go to Access Control > Rule and add a new access control rule. 1 ) Click Add New. 2 ) Give a name for the rule in the Rule Name field.
Chapter 4 3 ) Leave the status as Enabled as click Save. 6. Select Enable Internet Access Control to enable Access Control function. 7. Select Allow the packets specified by any enabled access control policy to pass through the Router as the default filter policy and click Save. Done! Now only the specific host(s) can visit the target(s) within the scheduled time period. 4. 11.
Chapter 4 4. 11. 1. Static Routing List 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Advanced Routing > Static Routing. ¾¾ To add static routing entries: 1. Click Add New. 2. Enter the following information. • • • Destination Network - The Destination Network is the address of the network or host that you want to assign to a static route.
Chapter 4 • Destination Network - The Destination Network is the address of the network or host to which the static route is assigned. • Subnet Mask - The Subnet Mask determines which portion of an IP address is the network portion, and which portion is the host portion. • Gateway - This is the IP address of the gateway device that allows for contact between the Router and the network or host.
Chapter 4 4. 12. 2. Rule List 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Bandwidth Control > Rule List, and you can view and configure the Bandwidth Control rules. • Description - This is the information about the rules such as address range. • Egress Bandwidth - This field displays the max and min upload bandwidth through the WAN port. The default is 0.
Chapter 4 4. 13. 1. Binding Settings 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to IP & MAC Binding > Binding Settings. 3. Select Enable for ARP Binding. 4. Click Save. ¾¾ To add IP & MAC Binding entries: 1. Click Add New. 2. Select the Bind checkbox. 3. Enter the MAC address and IP address. 4. Click Save. ¾¾ To modify or delete an existing entry: 1. Find the desired entry in the table. 2. Click Modify or Delete in the Modify column.
Chapter 4 4. 13. 2. ARP List To manage a device, you can observe the device on the LAN by checking its MAC address and IP address on the ARP list, and you can also configure the items. This page displays the ARP list which shows all the existing IP & MAC Binding entries. • MAC Address - The MAC address of the listed computer on the LAN. • IP Address - The assigned IP address of the listed computer on the LAN. • Status - Indicates whether or not the MAC and IP addresses are bound.
Chapter 4 To set up for DDNS, follow these instructions: 1. Enter the Domain Name received from your dynamic DNS service provider. 2. Enter the User Name for your DDNS account. 3. Enter the Password for your DDNS account. 4. Click Login. 5. Click Save. • Connection Status - The status of the DDNS service connection is displayed here. • Logout - Click Logout to log out of the DDNS service. Dyndns DDNS If the dynamic DNS Service Provider you select is www.dyn.com, the following page will appear.
Chapter 4 1. Enter the User Name for your DDNS account. 2. Enter the Password for your DDNS account. 3. Enter the Domain Name you received from dynamic DNS service provider here. 4. Click Login. 5. Click Save. • Connection Status - The status of the DDNS service connection is displayed here. • Logout - Click Logout to log out of the DDNS service. No-ip DDNS If the dynamic DNS Service Provider you select is www.noip.com, the following page will appear.
Chapter 4 4. 15. 1. IPv6 Status 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to IPv6 Support > IPv6 Status, and you can view the current IPv6 status information of the router. • WAN - This section shows the current IPv6 information of the router’s WAN port, including Connection Type, IPv6 Address information, IPv6 Default Gateway, Primary IPv6 DNS and Secondary IPv6 DNS.
Chapter 4 2. Go to IPv6 Support > IPv6 Setup. 3. Select the WAN Connection Type according to your ISP network topolopy: • SLAAC - Connections which use RADVD IPv6 address assignment. • Static IPv6 - Connections which use static IPv6 address assignment. • • • DHCPv6 - Connections which use dynamic IPv6 address assignment. PPPoEv6 - Connections which use PPPoEV6 that requires a username and password. Tunnel 6to4 - Connections which use 6to4 address assignment.
Chapter 4 • • • • • IPv6 Address Prefix - Display the IPv6 prefix length in dotted-decimal notation provided by your ISP. Default Gateway - Display the default gateway in colon-hexadecimal notation provided by your ISP. Connect - Click Connect to connect immediately. Disconnect - Click Disconnect to disconnect immediately.
Chapter 4 • Get IPv6 DNS Server Automatically - If your ISP does not give you any DNS IPv6 address, keep the default selection Get IPv6 DNS Server Automatically, and the DNS servers will be assigned from ISP dynamically. • • • Primary IPv6 DNS - Enter the DNS IPv6 address in colon-hexadecimal notation provided by your ISP. Secondary IPv6 DNS - Enter another DNS IPv6 address in colonhexadecimal notation provided by your ISP.
Chapter 4 PPPoEv6 • PPPoE Session - The PPP session type for IPv6 connection. There are two types: • • • • Share with PPPoEv4 - The PPPoEv6 and PPPoEv4 use the same PPP session. Create a new Session - The PPPoEv6 and PPPoEv4 use different PPP sessions. It is default to select this option. Username/Password - Enter the username and password provided by your ISP. These fields are case-sensitive. Address Mode - The way to get the IPv6 address and prefix.
Chapter 4 • Primary IPv6 DNS - Enter the DNS IPv6 address in colon-hexadecimal notation provided by your ISP. • • • • • Secondary IPv6 DNS - Enter another DNS IPv6 address in colonhexadecimal notation provided by your ISP. Use the following IPv6 DNS Servers - If your ISP gives you one or two DNS IPv6 addresses, select Use the following IPv6 DNS Servers and enter the Primary IPv6 DNS and Secondary IPv6 DNS in the corresponding fields. Connection Mode - The way to connect the ISP.
Chapter 4 • Secondary IPv6 DNS - Enter another DNS IPv6 address in colonhexadecimal notation provided by your ISP. 4. Select the Address Autoconfiguration Type which determines the way how the router assigns IPv6 address for PCs on the LAN: • • Address Autoconfiguration Type - RADVD (Router Advertisement Daemon) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server. Site Prefix Configuration Type - The type of IPv6 address prefix.
Chapter 4 3. Select your local time zone. 4. Enter the Date in Month/Day/Year format. 5. Enter the Time in Hour/Minute/Second format. 6. Click Save. ¾¾ To set time automatically: 7. Select your local time zone. 8. Enter the address or domain of the NTP Server I or NTP Server II. 9. Click Get GMT to get time from the Internet if you have connected to the Internet. ¾¾ To set Daylight Saving Time: 1. Select Enable DaylightSaving. 2. Select the start time from the drop-down list in the Start field. 3.
Chapter 4 • Diagnostic Tool - Select one diagnostic tool. • • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Tracerouter - This diagnostic tool tests the performance of a connection. Note: You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name is not, you might have a name resolution problem.
Chapter 4 4. Click Browse to locate the downloaded firmware file, and click Upgrade. 4. 16. 4. Factory Defaults 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to System Tools > Factory Defaults. Click Restore to reset all settings to the default values. • The default Username: admin • The default IP Address: 192.168.0.1 • • The default Password: admin The default Subnet Mask: 255.255.255.0 4. 16. 5.
Chapter 4 Note: During the restoring process, do not power off or reset the router. 4. 16. 6. Reboot 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to System Tools > Reboot, and you can restart your router. Some settings of the router will take effect only after rebooting, including: • Change the LAN IP Address (system will reboot automatically). • Change the DHCP Settings. • Change the Web Management Port.
Chapter 4 3. Click Save. 4. 16. 8. System Log 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to System Tools > System Log, and you can view the logs of the router. • Auto Mail Feature - Indicates whether the auto mail feature is enabled or not. • Mail Settings - Set the receiving and sending mailbox address, server address, validation information as well as the timetable for Auto Mail Feature. • • From - Your mail box address.
Chapter 4 • • SMTP Server - Your smtp server. It corresponds with the mailbox filled in the From field. You can log on the relevant website for help if you are not clear with the address. Authentication - Most SMTP Server requires Authentication. It is required by most mailboxes that need user name and password to log in. Note: Only when you select Authentication, do you have to enter the user name and password in the following fields.
Chapter 4 • Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button. If disabled, the function of DoS protection in Security settings will disabled. • Packets Statistics Interval (5-60) - The default value is 10. Select a value between 5 and 60 in the drop-down list. The Packets Statistic Interval indicates the time section of the packets statistic. • Sorted Rules – Choose how displayed statistics are sorted.
FAQ Q1. What can I do if I forgot my wireless password? The default wireless password is printed on the label of the router. If the password has been altered, please connect your computer to the router using an Ethernet cable and follow the steps below: 1. Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2. Go to Wireless > Wireless Security to retrieve or reset your wireless password. Q2.
3 ) Click LAN settings and deselect the following three options, and click OK.
4 ) Go to Advanced > Restore advanced settings, and click OK to save the settings. • Use another web browser or computer to log in again. • Reset the router to factory default settings and try again. If the login still fails, please contact the technical support. Note: You’ll need to reconfigure the router to surf the Internet once the router is reset. Q4. How to use the WDS Bridging function to extend my wireless network? For example, my house covers a large area.
2 ) Click Save. Note: Log in to the web management page again if the IP address of the router is altered. 3. Survey the SSID to be bridged: 1 ) Go to Wireless > Wireless Settings and click Enable WDS Bridging. 2 ) Click Survey, locate the root router’s SSID and click Choose (Here we take TP-LINK_2512 as example). 3 ) If the root router is set with a wireless password, you should enter the wireless password of the root router. 4 ) Click Save. 4.
Q5. What can I do if I cannot access the Internet even though the configuration is finished? 1. Visit http://tplinkwifi.net, and log in to with the username and password you set for the router. 2. Go to Status to check WAN status: If IP Address is a valid one, please try the methods below and try again: • Your computer might not recognize any DNS server addresses, please manually configure DNS server. 1 ) Go to DHCP. 2 ) Enter 8.8.8.8 as Primary DNS, and click Save. Tips: 8.8.8.
1 ) Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 2 ) Go to Network > MAC Clone, select Clone MAC Address and click Save. • • Tips: Some ISP will register the MAC address of your computer when you access the Internet for the first time through their Cable modem, if you add a router into your network to share your Internet connection, the ISP will not accept it as the MAC address is changed, so we need to clone your computer’s MAC address to the router.
• Double check the Internet Connection Type. 1 ) Confirm your Internet Connection Type, which can be learned from the ISP. 2 ) Visit http://tplinkwifi.net, and log in with the username and password you set for the router. 3 ) Go to Network > WAN. 4 ) Select your WAN Connection Type and fill in other parameters. 5 ) Click Save. 6 ) Restart the modem and the router. • Please upgrade the firmware of the router.
• On Windows 7 1 ) If you see the message No connections are available, it is usually because the wireless function is disabled or blocked somehow. 2 ) Clicking Troubleshoot and windows might be able to fix the problem by itself. • On Windows XP 1 ) If you see the message Windows cannot configure this wireless connection, this is usually because windows configuration utility is disabled or you are running another wireless configuration tool to connect the wireless.
2 ) If you cannot find the PIN or PIN failed, you may choose Connecting using a security key instead, and then type in the Wireless Password/Network Security Key. 3 ) If it continues to show note of Network Security Key Mismatch, it is suggested to confirm the wireless password of your wireless router. Note: Wireless Password/Network Security Key is case sensitive.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2016 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. RF Exposure Information This device meets the EU requirements (1999/5/EC Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body.
NCC Notice & BSMI Notice: 注意！ 依據 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅 自變更頻率、加大功率或變更原設計之特性或功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象 時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業 之無線電信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機 設備之干擾。 安全諮詢及注意事項 • 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 • 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 • 注意防潮，請勿將水或其他液體潑灑到本產品上。 • 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋 開口。 • 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位 置中。 • 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項 工作。 Продукт сертифіковано згідно с правилами
• The plug considered as disconnect device of adapter. • Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t hesitate to contact us. Explanations of the symbols on the product label Symbol Explanation DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).
