Specifications

ManualsBrandsTP-LINK ManualsNetworkingARCHER D5

Archer D5

AC1200 Wireless Dual Band Gigabit ADSL2+ Modem

Router

Rev: 1.0.0

1910011021

Summary of content (127 pages)

PAGE 1
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router Rev: 1.0.
PAGE 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD.
PAGE 3
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 4
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
PAGE 5
Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Korea Warning Statements: 당해 무선설비는 운용중 전파혼신 가능성이 있음.
PAGE 6
Safety Information    When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations.
PAGE 7
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router Model No.
PAGE 8
CONTENTS Package Contents ....................................................................................................1 Chapter 1. Product Overview...................................................................................2 1.1 Overview of the Modem Router ...................................................................................... 2 1.2 Main Features................................................................................................................. 3 1.
PAGE 9
4.7.2 Clients List.......................................................................................................................... 41 4.7.3 Address Reservation.......................................................................................................... 41 4.7.4 Conditional Pool ................................................................................................................. 42 4.8 Wireless 2.4GHz........................................................................
PAGE 10
4.13.1 IPv6 Default Gateway....................................................................................................... 77 4.13.2 IPv6 Static Route .............................................................................................................. 78 4.14 Forwarding.................................................................................................................... 79 4.14.1 Virtual Servers ................................................................................
PAGE 11
4.24 Logout......................................................................................................................... 111 Appendix A: Specifications .................................................................................112 Appendix B: Troubleshooting .............................................................................113 Appendix C: Technical Support ..........................................................................
PAGE 12
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package:  One Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router  One Power Adapter for Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router  Quick Installation Guide  One RJ45 cable  Two RJ11 cables  One ADSL splitter  One Resource CD for Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router, including:  This Use
PAGE 13
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Chapter 1. Product Overview Thank you for choosing the Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router. 1.1 Overview of the Modem Router The Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP.
PAGE 14
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 1.2 Main Features  Complies with IEEE 802.11ac to provide a wireless data rate of up to 300Mbps (2.4GHz) + 867Mbps (5GHz).  Four 10/100/1000Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port.  Provides external splitter.  Adopts Advanced DMT modulation and demodulation technology.  Supports bridge mode and Router function.  Multi-user sharing a high-speed Internet connection.
PAGE 15
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The modem router’s LEDs are located on the top panel (View from top to bottom). They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name (WPS) (USB) Status Indication On A wireless device has been successfully added to the network by WPS function.
PAGE 16
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide On There is a device connected to this LAN port, or the LAN port is sending or receiving data. Off There is no device connected to this LAN port. On Wireless is enabled. The modem router is working on 2.4GHz/5 GHz radio band. Off Wireless is disabled. On The network is available with a successful Internet connection. Off There is no successful Internet connection or the modem router is operating in Bridge mode.
PAGE 17
Archer D5 1.3.2 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide The Back Panel Figure 1-2  ADSL: Through the port, you can connect the telephone to the modem router. Or you can connect them by an external separate splitter. For details, please refer to 2.3 Connecting the Modem Router.  USB2, USB1: The USB port connects to a USB storage device or a USB printer.  WPS: The switch for the WPS function. For details, please refer to 4.8.2 WPS Settings.
PAGE 18
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Chapter 2. Connecting the Modem Router 2.1 System Requirements  Broadband Internet Access Service (DSL/Cable/Ethernet).  PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.  TCP/IP protocol on each PC.  Web browser, such as Microsoft Internet Explorer, Mozilla Firefox and Apple Safari. 2.
PAGE 19
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 2-1 8
PAGE 20
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0.
PAGE 21
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the modem router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.
PAGE 22
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Note: 1) Do not mix up the user name and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy. Go to Tools menu→Internet Options→Connections→LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 2.
PAGE 23
Archer D5 5. AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Select Yes and wait for 1-2 minutes to detect the connection type. Figure 3-6  Note: If the connection type can not be detected, please select No… and click Next to configure it manually (shown in Figure 3-7). Figure 3-7 A. Configuration for PPPoE/PPPoA Enter the Username, Password given by your ISP, and then click Next.
PAGE 24
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Note: If you are using the modem router on a new DSL line and have not completed your DSL provider’s online registration, you may be using a generic username and password. When registration is completed, you will need to update the username and password if you have created a new one. B. Configuration for Dynamic IP or Bridge This type doesn't need to be configured. C.
PAGE 25
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 3-11 8. On this page, please confirm all parameters. Click Back to modify or click the Save button to save your configuration. Figure 3-12 9. You will see the Complete screen below, click Finish to complete these settings.
PAGE 26
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 3-13 The basic settings for your modem router are completed. Please open the web browser and try to log on to http://www.tp-link.com to test your Internet connection.
PAGE 27
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Chapter 4. Configuring the Modem Router This chapter will show configuration for the key functions on the Web-based management page. 4.1 Login After your successful login, you will see the twenty-three main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below.
PAGE 28
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.2 Status Choose “Status”, you can see the corresponding information about Device Information, DSL, WAN, LAN and Wireless.
PAGE 29
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-1 18
PAGE 30
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.3 Quick Setup Please refer to 3.2 Quick Installation Guide. 4.4 Operation Mode Choose “Operation Mode”, and you will see the screen as shown in Figure 4-2. Select your desired mode and then click Save. Figure 4-2  DSL Modem Router Mode: The device enables multi-users to share Internet via ADSL using its ADSL port and share it wirelessly at 867Mbps wireless speeds over the crystal clear 5GHz band and 300Mbps over the 2.
PAGE 31
Archer D5 4.5.1 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide WAN Settings Choose “Network”“WAN Settings”, and you will see the WAN Port Information Table in the screen similar to Figure 4-3. There are six different configurations for the connection types, which are Static IP, Dynamic IP, PPPoE, PPPoA, IPoA and Bridge. You can select the corresponding types according to your needs.
PAGE 32
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-4 4.5.1.1 Static IP Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below.
PAGE 33
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-5 ATM Configuration:   VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. VCI (1~65535): Identifies the virtual channel endpoints in an ATM network. The valid range is from 1 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value provided by your ISP.
PAGE 34
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Gateway (Optional): Enter the gateway IP address in dotted-decimal notation provided by your ISP.  DNS Server/ Secondary DNS Server: Here you can set DNS Server (at least one) manually. The modem router will use the first DNS Server for priority.  Default Gateway: Select a WAN Interface from the drop-down list as the IPv4 default gateway.  Enable IPv6: Check the box to enable IPv6.
PAGE 35
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-6 Click Advance, advanced selections for WAN Service Setup can be shown.  MTU (bytes):. The default MTU (Maximum Transmission Unit) value is 1500 Bytes. Do not change the default value unless required by your ISP.  Enable NAT: This technology translates the IP addresses of a local area network to a different IP address for the Internet.
PAGE 36
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Get IP with Unicast: It is disabled by default. A few ISPs’ DHCP Servers do not support the broadcast applications. When the modem router cannot get the IP address normally, you can choose this option. (It is rarely required)  Set DNS Server manually: Choose “Set DNS Server manually”, you can set DNS Server manually here. The modem router will use this DNS Server for priority.
PAGE 37
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-7  PPP Username/Password/Confirm Password: Enter the User Name, Password and Confirm Password provided by your ISP. These fields are case-sensitive.  Always on: The connection can be re-established automatically when it is down.  Connect on demand: This mode is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time (MAX Idle Time), the connection will drop down automatically.
PAGE 38
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Enable IPv6: Check this box to enable IPv6.  Default Gateway: Select a WAN connection from the drop-down list as the IPv4 default gateway.  IPv6 Default Gateway: Select a WAN connection from the drop-down list as the IPv6 default gateway. Click Advance, advanced selections for WAN Service Setup can be shown.  Service Name/Server Name: Enter the Service Name and Server Name if it was provided by your ISP.
PAGE 39
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-8 4.5.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the Connection Type on the screen.
PAGE 40
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-9  IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP.  DNS Server/Secondary DNS Server: Type in your preferred DNS server.  Default Gateway: Select a WAN Interface from the drop-down list as the IPv4 default gateway. 4.5.1.6 Bridge If you select this type of connection, the modem router can be configured to act as a bridging device between your LAN and your ISP.
PAGE 41
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Note: After you finish the Internet configuration, please click Save to make the settings take effect. 4.5.2 Interface Grouping Choose “Network”“Interface Grouping”, you can view all the current groups on this page (shown in Figure 4-11).
PAGE 42
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-12 Click Save to make the entry effective immediately 4.5.3 LAN Settings Choose “Network”“LAN Settings” menu, and you will see the LAN screen (shown in Figure 4-13). Please configure the parameters for LAN ports according to the descriptions below. Figure 4-13  IP Address: You can configure the modem router’s IP Address and Subnet Mask for LAN Interface.
PAGE 43
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Enable IGMP Snooping: IGMP Snooping is the process of listening to IGMP (Internet Group Management Protocol) network traffic. The feature prevents hosts on a local network from receiving traffic for a multicast group they have not explicitly joined. It is enabled by default.
PAGE 44
Archer D5 2) AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide If DHCPv6 Server is selected, please complete the following parameters. Figure 4-15   Start IPv6 Address: Enter a value for the DHCPv6 server to start with when issuing IPv6 addresses.  End IPv6 Address: Enter a value for the DHCPv6 server to end with when issuing IPv6 addresses.
PAGE 45
Archer D5 4.5.5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide MAC Clone Choose menu “Network”“MAC Clone”, you can configure the MAC address of the WAN Interface as shown below. The WAN Interface List displays the WAN Interfaces you have configured on the section 4.5.1 WAN Settings and its default MAC Address. You can select the corresponding WAN Interface from the drop-down list and click Clone MAC To button to clone your current PC MAC, and then click Save.
PAGE 46
Archer D5    AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide L2TP Pass-through: L2TP (Layer Two Tunneling Protocol) is the method used to enable Point-to-Point sessions via the Internet on the Layer Two level. To allow L2TP tunnels to pass through the modem router, click Enable.
PAGE 47
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-21 This section will guide you to configure a VPN tunnel between two Archer D5s. The topology is as follows. Archer D5 Archer D5  Note: You could also use other VPN Routers to set VPN tunnels with Archer D5. Archer D5 supports up to 10 VPN tunnels simultaneously. Click Add New Connection in Figure 4-21 and then you will enter the screen shown in Figure 4-22.
PAGE 48
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-22  IPSec Connection Name: Enter a name for your VPN.  Remote IPSec Gateway Address (URL): Enter the destination gateway IP address which is the public WAN IP or Domain Name of the remote VPN server endpoint. (For example: Input 219.134.112.247 in Device1, Input 219.134.112.
PAGE 49
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Click Show Advanced Settings and then you can configure the Advanced Settings. We recommend you leave the Advanced Settings as default value. Figure 4-23  Mode: Select Main Mode to configure the standard negotiation parameters for IKE phase1.Select Aggressive Mode to configure IKE phase1 of the VPN Tunnel to carry out negotiation in a shorter amount of time.
PAGE 50
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-24  Enable IPTV: Check the box to enable IPTV function.  VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP.  VCI (1~65535): Identifies the virtual channel endpoints in an ATM network. The valid range is from 1 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value provided by your ISP.
PAGE 51
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-25  Group/ IP Address/ Subnet Mask: Displays group name, IP address and subnet mask. The parameters can be configured on the Interface Grouping page and LAN Settings page.  DHCP Server: If enabled, the modem router will work as a DHCP server, which provides the TCP/IP configuration for all the PC(s) that are connected to it on the LAN.
PAGE 52
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Note: 1) 2) 3) To use the DHCP server function of the modem router, you must configure all computers on the LAN as "Obtain an IP Address automatically". You have to disable NAT of the WAN connections, or the DHCP Relay may not take effect. If you select Disabled, the DHCP function will not take effect. Click the Save button to save your settings. 4.7.
PAGE 53
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-27    MAC Address: The MAC address of the PC for which you want to reserve an IP address. IP Address: The IP address reserved for the PC by the modem router. Status: The status of this entry, either Enabled or Disabled. To Reserve an IP address: 1. Click the Add New button. Then Figure 4-28 will pop up. 2. Enter the MAC address (in XX:XX:XX:XX:XX:XX format.
PAGE 54
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-29 To add a vendor class: 1. Click the Add New button. Then Figure 4-30 will pop up. 2. Enter parameters for the vendor class. Click the Save button. Figure 4-30 To modify or delete an existing entry: 1. Click Edit in the entry you want to modify the entry. 2. Modify the information. 3. Click the Save button. Click the Enable/Disable Selected button to make selected entries enabled/disabled.
PAGE 55
Archer D5 4.8 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Wireless 2.4GHz There are seven submenus under the Wireless 2.4Ghz menu: Basic Settings, WPS Settings, Wireless Security, Wireless Schedule, Wireless MAC Filtering, Wireless Advanced and Wireless Status. Click any of them, and you will be able to configure the corresponding function. 4.8.1 Basic Settings Choose menu “Wireless 2.4GHz” → “Basic Settings”, you can configure the basic settings for the wireless network of 2.
PAGE 56
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 11g only: Select if all of your wireless clients are 802.11g. 11n only: Select only if all of your wireless clients are 802.11n. 11bg mixed: Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed: Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. When 802.11g mode is selected, only 802.11g wireless stations can be connected to the modem router. When 802.11n mode is selected, only 802.
PAGE 57
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Authentication Type: This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It indicates the authorization type of the Root AP.  Password: If the AP your modem router is going to connect needs password, you need to fill the password in this blank. Click Save to save your settings. 4.8.
PAGE 58
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide You can also keep the default WPS Status as Enabled and click the Add device button in Figure 4-32, then Choose “Press the button of the new device in two minutes” and click Connect. (Shown in the following figure) Figure 4-33 Step 2: Press and hold the WPS button of the client device directly. Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process.
PAGE 59
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Setup process. Step 3: When the WPS LED is on, the client device has successfully connected to the modem router. Step 4: Refer back to your client device or its documentation for further instructions.  Note: 1) The WPS LED on the modem router will light green for five minutes if the device has been successfully added to the network.
PAGE 60
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Encryption: You can select Auto, TKIP or AES as Encryption.  Wireless Password: You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters. The default password is the same with the default PIN code, which is labeled on the bottom of the modem router or can be found in Figure 4-32.  Group Key Update Period: Specify the group key update interval in seconds. The value should be 30 or above.
PAGE 61
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Key Type: You can select the WEP key length (64-bit, or 128-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit: You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. 128-bit: You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters.
PAGE 62
Archer D5 4.8.5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Wireless MAC Filtering Choose menu “Wireless 2.4GHz”  ”Wireless MAC Filtering”, you can control the wireless access by configuring the Wireless MAC Filtering function, shown in Figure 4-37. Figure 4-37 To filter wireless users by MAC Address, click Enable. The default setting is Disabled.  MAC Address: The wireless station's MAC address that you want to filter.
PAGE 63
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide To edit or delete an existing entry: 1. Click the Edit in the entry you want to modify. 2. Modify the information. 3. Click the Save button. Click the Enable/ Disabled Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries.
PAGE 64
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-39  Transmit Power: Here you can specify the transmit power of the modem router. You can select 100%, 50% or 25%. 100% is the default setting and is recommended.  Beacon Interval: Enter a value between 25-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the modem router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons.
PAGE 65
Archer D5 4.8.7 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Wireless Status Choose menu “Wireless 2.4GHz””Wireless Status”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-40  MAC Address: The connected wireless station's MAC address.  Current Status: The connected wireless station's running status, one of STA-AUTH/ STA-ASSOC/ STA-JOINED/ WPA/ WPA-PSK/ WPA2/ WPA2-PSK/ AP-UP/ AP-DOWN/ Disconnected.
PAGE 66
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-41  SSID: Wireless network name. Enter a desired SSID which is case-sensitive and must not exceed 32 characters. The default SSID is TP-LINK_5GHz_XXXXXX (xx is the last six numbers of MAC address) .  Region: Select your region from the drop-down list. This field specifies the region where the wireless function of the modem router can be used.
PAGE 67
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  SSID (to be bridged): The SSID of the AP your modem router is going to connect to as a client. You can also use the search function to select the SSID to join.  BSSID (to be bridged): The BSSID of the AP your modem router is going to connect to as a client. You can also use the search function to select the BSSID to join.  Scan: Click this button, you can search the AP which runs in the current channel.
PAGE 68
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide button. b). To add a new device: If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and modem router using either Push Button Configuration (PBC) method or PIN method.  Note: To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function meanwhile. I.
PAGE 69
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-44 Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then click Connect button. Step 3: “Connect successfully” will appear on the screen of Figure 4-44, which means the client device has successfully connected to the modem router. III. Enter the modem router’s PIN on your client device Use this method if your client device asks for the modem router’s PIN number.
PAGE 70
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-45  Disable Wireless Security: If you do not want to use wireless security, check this radio button. But it’s strongly recommended to choose one of the below modes to ensure security.  WPA/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-shared passphrase. It is chosen by default.  Authentication Type: You can choose the type for the WPA/WPA2-Personal security on the drop-down list.
PAGE 71
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Authentication Type: Authentication Type: You can choose the type for the WPA/WPA2-Personal security on the drop-down list. The default setting is Auto, which can select WPA-PSK or WPA2-PSK as authentication type automatically based on the wireless station's capability and request.  Encryption: You can select Auto, TKIP or AES as Encryption.  RADIUS Server IP: Enter the IP address of the Radius Server.
PAGE 72
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Be sure to click the Save button to save your settings on this page. 4.9.4 Wireless Schedule Choose menu “Wireless 5GHz”“Wireless Schedule”, you can configure the Task Schedule as shown below. Figure 4-46  Note: The time you set is the period you need the wireless off. Before configure the wireless schedule, please set system time first which refer to 4.23.2 Time Settings, then you can enable or disable Wireless Schedule.
PAGE 73
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-47 To filter wireless users by MAC Address, click Enable. The default setting is Disabled.  MAC Address: The wireless station's MAC address that you want to filter.  Status: The status of this entry either Enabled or Disabled.  Host: The wireless network name (SSID).  Description: A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New button.
PAGE 74
Archer D5 3. AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Click the Save button. Click the Enable/ Disabled Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries.
PAGE 75
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-49  Transmit Power: Here you can specify the transmit power of the modem router. You can select 100%, 50% or 25%. 100% is the default setting and is recommended.  Beacon Interval: Enter a value between 25-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the modem router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons.
PAGE 76
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-50  MAC Address: The connected wireless station's MAC address  Current Status: The connected wireless station's running status, one of STA-AUTH/ STA-ASSOC/ STA-JOINED/ WPA/ WPA-PSK/ WPA2/ WPA2-PSK/ AP-UP/ AP-DOWN/ Disconnected  Received Packets: Packets received by the station  Sent Packets: Packets sent by the station Click on the Refresh button to update this page. 4.
PAGE 77
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-51  Guest Network: When enable this function, you can set wireless parameters for guest network.  SSID: The guest network name. When setting up a Guest network, it is strongly recommended to use a name that easily distinguishes it from your primary network. The default name is TP-LINK Guest_2.4GHz.  Security: It’s strongly recommended to enable WPA/WPA2-Personal.
PAGE 78
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-52  Guest Network: When enable this function, you can set wireless parameters for guest network.  SSID: The guest network name. When setting up a Guest network, it is strongly recommended to use a name that easily distinguishes it from your primary network. The default name is TP-LINK Guest_5GHz.  Security: It’s strongly recommended to enable WPA/WPA2-Personal.
PAGE 79
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.10.3 Guest Status 2.4GHz Choose menu “Guest Network”“Guest Status 2.4GHz”, you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-53  MAC Address: The connected wireless station's MAC address.  Current Status: The connected wireless station's running status.  Received Packets: Packets received by the station.
PAGE 80
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.11 USB Settings There are six submenus under the USB Settings menu, USB Mass Storage, User Accounts, Storage Sharing, FTP Server, Media Server and Print Server. Click any of them, and you will be able to configure the corresponding function. 4.11.
PAGE 81
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide when volume is non-shared, you can click the Activate button to share the volume. Click Disconnect to safely remove the USB storage device that is connected to USB port.  Note: Before removing the USB storage device, you should click “Disconnect” to make sure that all your data have been saved completely. Removing device directly may cause your USB storage device crashed. 4.11.
PAGE 82
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-57  Server Status: Indicates the Storage Sharing's current status.  Anonymous access to all the volumes: This function is enabled by default, so that users can access to all activated volumes without authentication. If you want to add a shared folder which does not allow anonymous login, uncheck the box. Then Folder Table will be displayed as shown below.  Share Name: This folder's display name.
PAGE 83
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-58 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter the display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries.
PAGE 84
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-59  Server Status: Indicates the FTP Server's current status.  Internet Access: If Internet Access is enabled, user(s) in public network can access FTP server via Internet Address.  Internet Address: If Internet Access is enabled, WAN IP will be displayed here.  Service Port: Enter the FTP Port number to use. The default is 21.  Share Name: This folder's display name.
PAGE 85
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-60 2. Click the Browse button, and then select the Select Volume from the drop-down list. 3. Enter display name of the share folder in Share Name filed. 4. Click the Apply button to apply the settings. You can click the upper button to go to the upper folder. Click the Enable/Disable Selected button to enable or disable the selected entries. Click the Delete Selected button to delete the selected entries.  Note: 1.
PAGE 86
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide b) Enter the name of the share folder in Share Name field. c) Click the Apply button to apply the configuration. Figure 4-62 Click the Scan now to scan all the share folders immediately. You can also select the Auto-scan, and, at the same time, select an auto scan interval time from the drop-down list. In this case, the media server will automatically scan the share folders.  Note: The max share folders number is 6.
PAGE 87
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.12.1 Default Gateway Choose “Route Settings”“Default Gateway”, you can see the Default Gateway screen. You can select a WAN Interface from the drop-down list as the system default gateway. Figure 4-64 Click the Add Interface button, you can add WAN Interfaces. Click the Save button to save your settings. 4.12.2 Static Route Choose “Route Settings” “Static Route”.
PAGE 88
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide static route.  Subnet Mask: It determines which portion of an IP Address is the network portion, and which portion is the host portion.  Gateway: Type in the correct gateway address for the static route.  Interface: Select the Interface from the drop-down list.  Status: Select Enabled or Disabled from the drop-down list. 3. Click Save to save your settings as shown in Figure 4-66.
PAGE 89
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-68 Click the Add Interface button, you can add WAN Interfaces. Click the Save button to save your settings. 4.13.2 IPv6 Static Route Choose “IPv6 Route Settings” “IPv6 Static Route”. You can see the IPv6 Static Route screen. This screen allows you to configure the IPv6 static routes (shown in Figure 4-69).
PAGE 90
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Prefix Length: The prefix length of the destination IPv6 address.  Gateway: Type in the correct IPv6 Gateway address for the IPv6 Static Route.  Interface: Select the Interface from the drop-down list.  Status: Select Enabled or Disabled from the drop-down list. 3. Click Save to save your settings. To modify or delete an existing entry: 1. Find the desired entry in the table. 2.
PAGE 91
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  IP Address: The IP address of the PC running the service application.  Protocol: The protocol used for this application. The options are TCP, UDP, or All (all protocols supported by the modem router).  Status: The status of this entry, "Enabled" means the virtual server entry is enabled.  Edit: To modify or delete an existing entry. To set up a virtual server entry: 1. Click the Add New button.
PAGE 92
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide System Tools –> Manage Control page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. 4.14.2 Port Triggering Choose menu “Forwarding”→ ”Port Triggering”, you can view and add port triggering in the next screen (shown in Figure 4-73). Some applications require multiple connections, such as Internet games, video conferencing, Internet telephoning and so on.
PAGE 93
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-74  Interface: Display the default gateway you have set in 4.5.1 WAN Settings.  Trigger Port: The port for outgoing traffic. An outgoing connection using this port will trigger this rule.  Trigger Protocol: The protocol used for Trigger Ports. The options are TCP, UDP, or All (all protocols supported by the modem router). .
PAGE 94
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Note: 1. 2. 3. When the trigger connection is released, the corresponding opened ports will be closed. Each rule can only be used by one host on the LAN at a time. The trigger connection of other hosts on the LAN will be refused. Open Ports ranges cannot overlap each other. 4.14.3 DMZ Choose menu “Forwarding→DMZ”, and then you can view and configure the DMZ host in the screen (shown in Figure 4-75).
PAGE 95
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide  Current UPnP Status: UPnP can be enabled or disabled by clicking the Enable or Disable button. This feature is enabled by default.  Current UPnP Settings List: This table displays the current UPnP information.  App Description: The description about the application which initiates the UPnP request.  External Port: The port which the modem router opens for the application.
PAGE 96
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-77  Enable Parental Control: Check the box if you want this function to take effect. This function is disabled by default.  MAC Address of Parental PC: In this field, enter the MAC address of the controlling PC, or you can make use of the Copy To Above button below.  MAC Address of Current PC: This field displays the MAC address of the PC that is managing this modem router.
PAGE 97
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.16 Firewall There are four submenus under the Firewall menu: Rule, LAN Host, WAN Host and Schedule. Click any of them, and you will be able to configure the corresponding function. 4.16.1 Rule Choose menu “Firewall” → “Rule”, and then you can view and set access control rules in the screen as shown in Figure 4-78.
PAGE 98
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide The methods to add a new rule: 1. Click the Add New button and the next screen will pop up as shown in Figure 4-79. 2. Give a name (e.g. Rule_1) for the rule in the Description field. 3. Select a host from the LAN Host drop-down list or choose “Add LAN Host”. 4. Select a target from the WAN Host drop-sown list or choose “Add WAN Host”. 5. Select a schedule from the Schedule drop-down list or choose “Add Schedule”. 6.
PAGE 99
Archer D5  AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button. 2. In the Mode field, select IP Address or MAC Address.  If you select IP Address, please follow the steps below: 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In IP Address field, enter the IP address.
PAGE 100
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In IP Address field, enter the IP address. If you select MAC Address, the screen shown is Figure 4-83. Figure 4-83 1) In Description field, create a unique description for the host (e.g. Host_1). 2) In MAC Address field, enter the MAC address. If you select URL Address, the screen shown is Figure 4-84.
PAGE 101
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-85  Description: Here displays the description of the schedule and this description is unique.  Edit: Here you can modify an existing schedule. To add a new schedule, follow the steps below: 1. Click Add New button and the next screen will pop-up as shown in Figure 4-86. 2. In Description field, create a unique description for the schedule (e.g. Schedule_1). 3. In Apply To field, select the day or days you need. 4.
PAGE 102
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.17 IPv6 Firewall There are four submenus under the IPv6 Firewall menu: IPv6 Rule, IPv6 LAN Host, IPv6 WAN Host and IPv6 Schedule. Click any of them, and you will be able to configure the corresponding function. 4.17.1 IPv6 Rule Choose menu “IPv6 Firewall” → “IPv6 Rule”, and then you can view and set access control rules in the screen as shown in Figure 4-87.
PAGE 103
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-88 2. Give a name (e.g. Rule_1) for the rule in the Description field. 3. Select a host from the IPv6 LAN Host drop-down list or choose “Add IPv6 LAN Host”. 4. Select a host from the IPv6 WAN Host drop-sown list or choose “Add IPv6 WAN Host”. 5. Select a schedule from the IPv6 Schedule drop-down list or choose “Add IPv6 Schedule”. 6. In the Action field, select Deny or Allow to deny or allow your entry. 7.
PAGE 104
Archer D5  AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Edit: To modify an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button, and you will see the screen as shown in Figure 4-90. Figure 4-90 2. Create a unique name for the host (e.g. Host_1) in the Description field. 3. Enter an IPv6 address in the IPv6 Address field. 4. Enter the prefix length of the IPv6 address in the Prefix Length field. 5.
PAGE 105
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-92 2. Create a unique description for the host (e.g. Host_1) in the Description field. 3. Enter an IPv6 address in the IPv6 Address field. 4. Enter the prefix length of the IPv6 address in the Prefix Length field. 5. Click the Save button to save the settings. Click the Delete Selected button to delete the selected entries. 4.17.
PAGE 106
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-94 2. Create a unique description for the schedule (e.g. Schedule_1) in Description field. 3. Select the day or days you need in Apply To field. 4. In time field, you can select all day-24 hours or you may enter the Start Time and Stop Time in the corresponding field. 5. Click Save to save the settings. Click the Clear Schedule button to clear your settings in the table.
PAGE 107
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-95  Enable: Check the box to enable IPv6 Tunnel function. It is disabled by default.  Mechanism: Select a type for IPv6 tunnel from the drop-down list. DS-Lite, 6RD and 6to4 are supported. 1) DS-Lite This type is used in the situation that your WAN connection is IPv6 while LAN connection is IPv4. Select DS-Lite, and you will see the screen as shown in Figure 4-96.
PAGE 108
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-97  WAN Connection: Select a WAN connection from the drop-down list. Only the connected WAN connections can be shown in the drop-down list.  Configuration Type: Select a configuration type for this tunnel. Auto means to obtain the following parameters automatically while Manual means you set them up manually. If Auto is selected, only Dynamic IP WAN connection can be selected from the drop-down list.
PAGE 109
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4.19 Bandwidth Control Choose menu “Bandwidth Control”, and then you can configure the Upstream Bandwidth and Downstream Bandwidth in the next screen. The values you configure should be less than 1000000Kbps. For optimal control of the bandwidth, please select the right Line Type and consult your ISP for the total bandwidth of the egress and ingress.
PAGE 110
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-100 3. Click the Save button. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete the selected entries. 4.20 IP&MAC Binding There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List. Click any of them, and you will be able to scan or configure the corresponding function.
PAGE 111
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Edit button, and then you will go to the next page. This page is used for adding or modifying an IP & MAC Binding entry (shown in Figure 4-102.) Figure 4-102 To add IP & MAC Binding entries, follow the steps below. 1. Click the Add New button as shown in Figure 4-101. 2. Enter the MAC Address and IP Address. 3.
PAGE 112
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Click the Delete Selected button to delete the selected entries. Click the Refresh button to refresh all items. 4.21 Dynamic DNS Choose menu “Dynamic DNS”, and you can configure the Dynamic DNS function.
PAGE 113
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-105 4.23 System Tools Choose menu “System Tools”, and you can see the submenus under the main menu: System Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore, Factory Defaults, Firmware Upgrade, Reboot and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.23.
PAGE 114
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-106  Log Type: Select the log type to be displayed.  Log Level: Select the log level to be displayed.  Refresh: Refresh the page to show the latest log list.  Clear Log: All the logs will be deleted from the modem router permanently, not just from the page.  Save Log: Click to save all the logs in a txt file.  Log Settings: Click to set the logs in the screen (shown in Figure 4-107).
PAGE 115
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-108  Time Zone: Select your local time zone from this drop-down list.  Date: Enter your local date in MM/DD/YY into the right blanks.  Time: Enter your local time in HH/MM/SS into the right blanks.  NTP Server 1 / NTP Server 2: Enter the address or domain of the NTP Server 1 or NTP Server 2, and then the modem router will get the time from the NTP Server preferentially.
PAGE 116
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-109  Current User Status: This box displays the information about User Type, User Name, Host IP Address and Host MAC Address.  Account Management: Here you can set the account user information about New User Name and New Password.  Service Configuration: Here you can modify the port of the modem router’s web management interface and limit the hosts which can log into this modem router’s web management interface.
PAGE 117
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-110  CWMP: Select Enable to enable the CWMP function.  Inform: If enabled, the information will be informed to ACS server periodically.  Inform Interval: Enter the interval time here.  ACS URL: Enter the website of ACS which is provided by your ISP.  ACS User Name/Password: Enter the User Name and password to log in the ACS server.
PAGE 118
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-111 An SNMP Agent is an application running on the modem router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs. So a router contains SNMP "agent" software can be monitored and/or controlled by SNMP Manager using SNMP messages. 4.23.
PAGE 119
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-113 Click the Restore button to reset all configuration settings to their default values.  The default User Name: admin  The default Password: admin  The default Subnet Mask: 255.255.255.0  Note: All changed settings will be lost when factory defaults are restored. 4.23.
PAGE 120
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide want to use. 2) When upgrade the modem router's firmware, you may lose its current configurations, so please write down some of your customized settings before upgrading the firmware. 3) Do not turn off the modem router or press the Reset button while the firmware is being upgraded. Loss of power during the upgrade could damage the modem router. 4) The firmware version must correspond to the hardware.
PAGE 121
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Figure 4-116  Traffic Status: If it is disabled, the function of DoS protection in Security settings will be disabled.The default value is disabled. To enable it, click the Enable.  Statistics Interval (5-60): Indicates the time section of the packets statistic. The default value is 10. Select a value between 5 and 60 seconds in the drop-down list. Click Reset All to reset the values of all the entries to zero.
PAGE 122
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Reset Reset the value of the entry to zero. Delete Delete the existing entry in the table. Operation 4.24 Logout Choose “Logout”, and you will back to the login screen as shown in Figure 4-117.
PAGE 123
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Appendix A: Specifications General ANSI T1.413, ITU G.992.1, ITU G.992.3, ITU G.992.5, Standards and Protocols Safety & Emission IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.11ac, IEEE 802.3, IEEE 802.3u, IEEE802.3ab, TCP/IP, PPPoA, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT FCC, CE Four 10/100/1000M Auto-Negotiation RJ45 ports（Auto MDI/MDIX) Ports One RJ11 port Two USB 2.
PAGE 124
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my modem router’s configuration to its factory default settings? With the modem router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it.  Note: Once the modem router is reset, the current configuration settings will be lost and you will need to re-configure the router. T2.
PAGE 125
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide 4） Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. For Windows 8 1） Move your mouse to the lower right corner and you will see Search icon in the Popups. Go to “ -> Apps”. Type Control Panel in the search box and press Enter, then you will go to Control Panel. 2） Click “View network status and tasks > Change adapter settings”.
PAGE 126
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your modem router’s factory default settings and reconfigure your modem router following the instructions in 3.2 Quick Installation Guide. Please feel free to contact our Technical Support if the problem still exists. T4.
PAGE 127
Archer D5 AC1200 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide Appendix C: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq  To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download  For all other technical support, please contact us by using the following details:  Global Tel: +86 755 2650 4400 Fee: Depending on rate of different carriers, IDD. E-mail: support@tp-link.