Deco X55 Superior Mesh Wi-Fi, Everywhere User Guide AX3000 Whole Home Mesh Wi-Fi 6 System 1910013325 REV1.26.
Contents About This Guide ···················································· 1 Appearance ······························································· 2 Set Up Your Deco ··················································· 3 Troubleshooting ······················································ 7 Authentication ·························································· 8
About This Guide This guide provides a brief introduction to AX3000 Whole Home Mesh Wi-Fi 6 System and regulatory information. Features available in Deco may vary by model and software version. Deco availability may also vary by region or ISP. All images, steps, and descriptions in this guide are only examples and may not reflect your actual Deco experience.
Appearance Each Deco has an LED that changes color according to its status, three RJ-45 Ethernet ports, a power slot, and a Reset button. See the explanation below: Tip: The product label can be found at the bottom of the product. Pulse Yellow: Deco is resetting. Solid Yellow: Deco is starting up. Pulse Blue: Deco is ready for setup. Solid Blue: Deco is setting up. Pulse Green: Deco is upgrading firmware. Solid Green: Deco is all set up and connected.
Set Up Your Deco First let's start by setting up the Deco network. Get the TP-Link Deco app for iOS or Android, then follow the app to walk through the setup. 1. Get the Deco app 2. Log in or sign up with TP-Link ID 3. Select your Deco model Scan the QR code below or go to Google Play or the App Store to download the Deco app. Install the app on your Android or iOS smartphone or tablet. Open the app and log in with your TP-Link ID. If you don’t have a TP-Link ID, create one first.
4. Plug in your Deco 5. Connect to your Deco's Wi-Fi 6. Specify your Deco's location Power off your modem. Connect your Deco to the modem and power them both on. Connect your phone/tablet to the Deco's Wi-Fi using the default SSID printed on the product label. Select or custom a location for your Deco. The location will be used as the name of your Deco. If you don't have a modem, connect your Deco directly to the Ethernet outlet.
. Connect your Deco to the internet 8. Create your Wi-Fi network 9. Connect to your Wi-Fi network Select the internet connection type and enter the information. If you are not sure, contact your internet service provider. Set a network name and a password. These will be the name and password you use to connect your devices to Wi-Fi. Connect your phone/tablet to the Deco's Wi-Fi.
10. Setup complete Your Deco network is now up. You can connect your devices to the Deco network.
Troubleshooting Solutions to common problems during setup or use are provided here for reference. Follow the steps and the provided link below to diagnose and solve problems you might experience with your Deco. If problems still exist, contact us: https://www.tp-link.com/support Q1. What should I do if I fail to configure the main Deco and get stuck on “We couldn't find Deco”? Refer to the guide https://www.tp-link.com/support/faq/2239/ or follow the video https://youtu.be/2HYuEYS9XJM Q2.
Authentication FCC Compliance Information Statement Product Name: AX3000 Whole Home Mesh Wi-Fi 6 System Model Number: Deco X55 Component Name I.T.E Power Supply Model T120150-2B4 Responsible party: TP-Link USA Corporation Address: 10 Mauchly, Irvine, CA 92618 Website: http://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
• Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Compliance Information Statement Product Name: I.T.E POWER SUPPLY Model Number: T120150-2B4 Responsible party: TP-Link USA Corporation Address: 10 Mauchly, Irvine, CA 92618 Website: http://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6804 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. OPERATING FREQUENCY(the maximum transmitted power) 2412MHz—2472MHz (20dBm) 5150MHz—5350MHz (23dBm) Frequency band 5150 - 5250 MHz: Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted.
National restrictions Attention: This device may only be used indoors in all EU member states and EFTA countries, and Northern Ireland. AT BE BG CH CY CZ DE DK EE EL ES FI FR HR HU IE IS LT LU LV MT NL IT LI NO PL PT RO SE SI SK UK(NI) UKCA Mark UK Declaration of Conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. l’appareil ne doit pas produire de brouillage; 2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.
Korea Warning Statements: 당해 무선설비는 운용중 전파혼신 가능성이 있음.
限用物質及其化學符號 單元 Unit PCB Restricted substances and its chemical symbols 鎘 六價鉻 多溴聯苯 鉛 汞 Lead Mercury Cadmium (Pb) (Hg) (Cd) ○ ○ − − ○ ○ ○ ○ 多溴二苯醚 Hexavalent chromium Polybrominated biphenyls Polybrominated diphenyl ethers (Cr+6) (PBB) (PBDE) ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 外殼 電源供應器 其他及其配件 備考1. 超出0.1 wt %” 及 “超出0.01 wt %” 系指限用物質之百分比含量超出百分比含量基準值。 Note 1：“Exceeding 0.1 wt %” and “exceeding 0.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. • Do not use damaged charger or USB cable to charge the device. • Do not use any other chargers than those recommended. • Do not use the device where wireless devices are not allowed. • Adapter shall be installed near the equipment and shall be easily accessible. • Use only power supplies which are provided by manufacturer and in the original packing of this product.
Symbol Explanation Class II equipment RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
