Quick Installation Guide

ManualsBrandsTP-Link ManualsComputersEAP235-Wall Omada AC1200 PoE-Compliant Wireless Gigabit Wall Plate Access Point

Wireless Wall Plate Access Point

Bottom View

RESET Button

With the device powered on, press and hold the button for about ve seconds until the LED ashes,

then release the button. The device will restore to its factory defaults.

ETH1 & ETH2 Port

Connected to a client device to transmit data.

ETH3 (PoE OUT) Port

Connected to a client device to transmit data and supply power (PoE Passthrough). The PoE OUT

feature requires 802.3at PoE+ input and the maximum output is 13 W.

RESET

ETH1 ETH2 ETH3 (PoE OUT)

Pre-Installation Checklist

Note: To power an 802.3af device in the LAN, you must use 802.3at PoE+ input.

Installation Steps

The EAP can be mounted into an 86 mm wall junction box, a standard EU wall junction box, or a

standard US junction box. The junction box should be pre-installed with a running-in-wall Ethernet

cable connected to a PoE switch.

Standard EU wall junction box86 mm wall junction box Standard US wall junction box

Note: For simplicity, the 86 mm wall junction box is used as an example below.

1. Detach the faceplate of the junction box with a Phillips screwdriver.

2. Insert the enclosed screws and tighten them with a Philips screwdriver to secure the mounting

bracket.

3. Connect the Ethernet cable inside the junction box to an RJ45 plug. Then connect the cable to

the ETH0 (PoE IN) port. Position the Ethernet cable to ensure it is not strained.

Note:

If the junction box does not have enough room to accommodate the EAP, replace the junction box with

an open‑end junction box or a deeper one.

4. Attach the EAP to the mounting bracket by aligning the two mounting studs on the mounting

bracket with the large openning of the slots on the EAP. Press and slide the EAP down until it

locks into place.

Note:

Do not over tighten the screws.

If the enclosed screws do not t the junction box, use the screws attached to the junction box instead.

When mounting the bracket to a standard US junction box, use the holes on the top and bottom sides.

Setup with videos

Scan QR code or visit https://www.tp-link.com/support/setup-video/

Before installation, be sure that you have the following items:

A pre-installed wall junction box

An RJ45 plug

A Phillips screwdriver

A PoE switch

Hardware Overview

Front Panel & Rear Panel

LED

ETH0 (PoE IN)

LED Button

Locking Tab

LED Indicator

On: Working normally/Initializing.

O: Working abnormally/Power o/LED is turned o.

Flashing:

Initialization: The LED ashes twice after initialization is completed.

Upgrade: The LED ashes once per second while upgrading.

Reset: The LED ashes quickly during the reset. The EAP will then reboot.

Locate: When the Locate feature is activated in the Omada controller, the LED ashes quickly to

locate and identify the device. The LED will ash for 10 minutes, or you can disable the feature

manually to stop it ashing.

ETH0 (PoE IN) Port

Connected to a PSE (Power Sourcing Equipment), such as a PoE switch, for both data

transmission and Power. The device supports 802.3af/at inputs.

LED Button

Press the LED button to turn on/o the LED.

Note: The image may dier from the actual product.

Summary of content (2 pages)

PAGE 1
Bottom View 2. Insert the enclosed screws and tighten them with a Philips screwdriver to secure the mounting bracket. RESET ETH1 Quick Installation Guide ETH2 ETH3 (PoE OUT) RESET Button With the device powered on, press and hold the button for about five seconds until the LED flashes, then release the button. The device will restore to its factory defaults. Wireless Wall Plate Access Point ETH1 & ETH2 Port Connected to a client device to transmit data.
PAGE 2
Tip: To remove the EAP from the mounting bracket, insert a paper clip into the hole next to the LED button to release the Locking Tab. Slide the EAP upwards and pull it out to detach it from the mounting bracket, as shown below. Option2: Controller Mode Controller Mode is applicable to configuration for mass EAPs. All EAPs can be centrally configured and monitored via Omada Software Controller, Omada Hardware Controller (OC200/OC300) or Omada Cloud-Based Controller.