Quick Installation Guide

Quick Installation Guide
Setup with videos
Visit https://www.tp-link.com/support/setup-video/ or scan the QR
code to search for the setup video of your product model.
Power LED PoE Port
Indoor/Outdoor Access Point
Overview
Package Contents
Panel Layout
© 2021 TP-Link 7106509165 REV1.0.0
Passive PoE Adapter
LED Status
Indication
Solid green
The device is initializing or working properly.
Flashing yellow
System errors. RAM, Flash, Ethernet, WLAN or
rmware may be malfunctioning.
Flashing yellow, green
Firmware update is in progress. Do not disconnect
or power o the device.
Quickly ashing yellow, green
The device is being reset to its factory default
settings.
Flashes green twice
Initialization is completed.
SYS LED Explanation
Quickly ashing green
Locate the device.
Slowly ashing green
The device is in an isolated state.
1
Lightning and ESD Protection
Before mounting the EAP, you should consider Lightning and ESD
Protection to ensure safety.
Proper grounding is extremely important for outdoor devices. To reduce
the damage of potential lightning and ESD attacks, connect the
grounding terminal to grounding facilities using a proper grounding wire,
which should meet the local installation requirements. You need to secure
the grounding wire to the grounding terminal with the screw.
Hardware Installation
Mount the EAP
The EAP can be pole-mounted or wall-mounted. Follow the steps below
for the appropriate installation.
Option 1: Pole Mounting
Lead the end of the pole mounting strap
through the back of the EAP.
Step 1:
Position the EAP and wrap the pole
mounting strap around the pole. Feed the
end through the screw-block and tighten
the strap until the EAP is secure.
Step 2:
Option 2: Wall Mounting
Step 1:
Place the mounting bracket (for EAP) in
the right position. Mark two positions
for the screw holes .
Drill two 6 mm holes for the screws at
the marked positions.
Step 2:
Insert the plastic wall anchors into the 6
mm holes. Align the bracket (for EAP) to
the plastic wall anchors and drive the
self-tapping screws into the anchors
through the bracket (for EAP).
Step 3:
Align the mounting tabs on the back of
the EAP with the slot of the mounting
bracket (for EAP). Push and slide the
EAP downward until it locks into place.
3
Connect the Cable
Fit an Ethernet cable through the Spiral Cover, Bracket, and O-Ring, and
connect the cable to the port.
Note: It’s recommended that you scan the QR code and
watch the installation video. If you have any trouble in this
process, please follow the instructions below step by step.
Fit the O-Ring to the head of the Bracket and screw the Bracket to the
body of the device.
Note: Don’t warp the O-Ring.
Fit the Ethernet cable through the Seal’s slit with the thicker side
towards the Bracket, and plug the seal to the Bracket.
Note: Choose the proper Seal according to the type and diameter of the
Ethernet cable.
Screw the Spiral Cover to the Bracket.
RESET Grounding
Terminal
Ethernet
Port LAN
M3×28 Plastic Wall
Anchors (Qty.4)
M3×20
Self-tapping
Screws (Qty.2)
Mounting Bracket
(for EAP)
Pole Mounting Strap
Mounting Kit
M3×16
Self-tapping
Screws (Qty.2)
M3×6 Screw
(For Securing the
Grounding Wire)
2
1
2
3
4
LAN Port
Passive PoE Adapter
(Mounting Bracket Included)
Power Cord
Installation GuideEAP
Spiral Cover
O-Ring
Bracket
Waterproof Kit
Seal
(For Unshielded Cable)
O-Ring
Bracket
EAP
Grounded PoE Adapter
Ethernet Cable
Grounded 3-wire
Power Outlet
1
3
4
2
Seal
(For Shielded Cable)
Spiral Cover
Seal