Quick Installation Guide

ManualsBrandstp-link ManualsComputers & AccessoriesAX1800 Ceiling Mount Wi-Fi 6 Access Point

Table Of Contents

7106509200-EAP660 HD多机型IG

Wireless Access Point

Setup with videos

Visit https://www.tp-link.com/support/setup-video/ or scan the QR code to search for

the setup video of your product model.

Note: For simplicity, we will take EAP660 HD for example throughout the Guide. The image may dier from the

actual product.

Hardware Overview

On:

Working normally/Initializing.

Off:

Working abnormally/Power o/LED is turned o.

Flashing:

Initialization

: The LED ashes twice after initialization is completed.

Upgrade

: The LED ashes once per second while upgrading.

Reset

: The LED ashes quickly during the reset. The EAP will then reboot.

Locate

: When the Locate feature is activated in the Omada controller, the LED ashes quickly to locate and

identify the device. The LED will ash for 10 minutes, or you can disable the feature manually to stop it ashing.

LED Indicator

RESET

With the device powered on, press and hold the button for about 5 seconds until the LED flashes quickly . Then release the

button. The device will restore to factory default settings.

The port is used to connect to a router or a switch to transmit data, or to a PSE (Power Sourcing Equipment), such as a PoE switch,

for both data transmission and Power over Ethernet (PoE) through Ethernet cable. The port supports transmission speed of

10/100/1000/2500 Mbps for EAP660 HD and 10/100/1000 Mbps for EAP610 / EAP620 HD.

Ethernet Port: 2.5G ETH (PoE) (for EAP660 HD) | ETH (PoE) (for EAP610 / EAP620 HD)

Plug one end of the provided power adapter to this port and the other end to a standard electrical wall outlet to power the EAP.

Power Port: 12V 2A (for EAP660 HD) | 12V 1A (for EAP610 / EAP620 HD)

Insert the plastic wall anchors into the 6 mm

diameter holes.

Connect the Ethernet cable to the Ethernet port on

the EAP.

Attach the EAP to the mounting bracket, then

rotate the EAP until it locks into place, as shown on

the left.

M3×20 Self-tapping Screws (Qty.4)

M3×28 Plastic Wall Anchors (Qty.4)

If your Ethernet cable feeds through the wall, you

can position the mounting bracket below the cable

hole. Mark four positions for the screw holes and

then drill four 6 mm diameter holes at the marked

positions.

Secure the mounting bracket to the wall by driving

the self-tapping screws into the anchors. Make

sure that the shoulders of the mounting bracket are

on the outside.

Remove the ceiling tile.

Place the mounting bracket in the center of the

ceiling tile. Mark four positions for the screw

holes and a position for the Ethernet cable hole.

Drill four 4 mm diameter holes for the screws and

a 25 mm diameter hole for the Ethernet cable at

the marked positions.

Secure the mounting bracket to the ceiling tile

using four M3x30 pan-head screws, washers and

wing nuts, as shown on the left.

Feed the Ethernet cable through the hole and set

the ceiling tile back into place.

Connect the Ethernet cable to the Ethernet port.

Attach the EAP to the mounting bracket, then

rotate the EAP until it locks into place, as shown on

the left.

Note: Make sure that the ceiling tile is bigger than the EAP.

Wing Nuts (Qty.4)Washers (Qty.4) M3×30 Pan-head Screws (Qty.4)

The EAP can be ceiling-mounted or wall-mounted. Choose a mounting method according to your

needs. Follow the steps below for the appropriate installation.

Hardware Installation

Drill Hole for Ethernet cable

Front Panel

Rear Panel

Option 1: Ceiling Mounting Option 2: Wall Mounting

Option1: Ceiling Mounting

Option2: Wall Mounting

Summary of content (23 pages)

PAGE 1
2 Hardware Installation The EAP can be ceiling-mounted or wall-mounted. Choose a mounting method according to your needs. Follow the steps below for the appropriate installation. Option2: Wall Mounting M3×28 Plastic Wall Anchors (Qty.4) Quick Installation Guide Wireless Access Point Option 1: Ceiling Mounting Option 2: Wall Mounting Setup with videos Washers (Qty.4) M3×30 Pan-head Screws (Qty.4) 1 Hardware Overview Note: For simplicity, we will take EAP660 HD for example throughout the Guide.
PAGE 2
3 Power Supply The EAP can be powered via a power adapter or a PSE device (such as a PoE switch). Option1: Via PoE Switch (Compliant with 802.3at) Option2: Controller Mode Controller Mode applies to the large scale network with mass devices. All devices can be centrally configured and monitored via Omada Software Controller, Omada Hardware Controller or Omada Cloud-Based Controller. Omada Cloud-Based Controller PoE Switch (Compliant with 802.
PAGE 3
Regulatory Compliance EAP
PAGE 4
For Class A EAP with adapter: FCC Compliance Information Statement Product Name: Omada EAP Model Number: EAP110 / EAP110-Outdoor / EAP660 HD Component Name I.T.E. Power Supply Model TL-POE2406 (For EAP110 / EAP110-Outdoor) T120200-2B1 (For EAP660 HD) Responsible party: TP‑Link USA Corporation, d/b/a TP‑Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp‑link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6803 E‑mail: sales.usa@tp‑link.
PAGE 5
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.
PAGE 6
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date:2020-5-12 CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
PAGE 7
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. For EAP110-Outdoor: This radio transmitter (IC: 8853A-EAP110OD / Model: EAP110-Outdoor) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated.
PAGE 8
第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。安全諮詢及注意事項 ■■ 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ■■ 清潔本產品之前請先拔掉電源線 . 請勿使用液體、噴霧清潔劑或濕布進行清潔。 ■■ 注意防潮，請勿將水或其他液體潑灑到本產品上。 ■■ 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ■■ 請勿將本產品置放於靠近熱源的地方 .
PAGE 9
■■ Do not use the device where wireless devices are not allowed ■■ Adapter shall be installed near the equipment and shall be easily accessible. ■■ Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t hesitate to contact us. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device.
PAGE 10
For Class B EAP with adapter: FCC Compliance Information Statement Product Name: Omada EAP Model Number: EAP115 / EAP225 / EAP245 / EAP265 HD / EAP610 / EAP620 HD / EAP660 HD / EAP225-Outdoor / EAP610-Outdoor Component Name Model T090060-2B1 (For EAP115) I.T.E.
PAGE 11
•• Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 12
•• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •• Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 13
EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce. RF Exposure Information This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
PAGE 14
Le présent émetteur radio (IC: 8853A-EAP225OD / Model: EAP225-Outdoor) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste ci-dessous et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Antenna Two 2.
PAGE 15
Korea Warning Statements 당해 무선설비는 운용중 전파혼신 가능성이 있음 . NCC Notice & BSMI Notice 注意！依據低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性或功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。針對EAP225 / EAP245 / EAP265 HD / EAP610 /EAP620 HD / EAP660 HD / EAP225-Outdoor： 4.7.9.1應避免影響附近雷達系統之操作。 4.7.9.2高增益指向性天線只得應用於固定式點對點系統。安全諮詢及注意事項 ■■ 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ■■ 清潔本產品之前請先拔掉電源線 .
PAGE 16
Safety Information ■■ Keep the device away from water, fire, humidity or hot environments. ■■ Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. ■■ Do not use damaged charger or USB cable to charge the device. ■■ Do not use any other chargers than those recommended. ■■ Do not use the device where wireless devices are not allowed ■■ Adapter shall be installed near the equipment and shall be easily accessible.
PAGE 17
RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
PAGE 18
For Class B EAP with no adapter: FCC Compliance Information Statement Product Name: Omada EAP Model Number: EAP115-Wall / EAP225-Wall / EAP230-Wall / EAP235-Wall / EAP615-Wall Responsible party: TP‑Link USA Corporation, d/b/a TP‑Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp‑link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6803 E‑mail: sales.usa@tp‑link.
PAGE 19
Note: The manufacturer is not responsible for any radio or T V interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
PAGE 20
RF Exposure Information This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body. National Restrictions For EAP225-Wall / EAP230-Wall / EAP235-Wall: Attention: In EU member states and EFTA countries, the operation in the frequency range 5150MHz - 5350MHz is only permitted indoors.
PAGE 21
DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 54705600MHz, and 5650-5725MHz.
PAGE 22
4.7.9.1應避免影響附近雷達系統之操作。 4.7.9.2高增益指向性天線只得應用於固定式點對點系統。安全諮詢及注意事項 ■■ 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ■■ 清潔本產品之前請先拔掉電源線 . 請勿使用液體、噴霧清潔劑或濕布進行清潔。 ■■ 注意防潮，請勿將水或其他液體潑灑到本產品上。 ■■ 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ■■ 請勿將本產品置放於靠近熱源的地方 . 除非有正常的通風，否則不可放在密閉位置中。 ■■ 不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。限用物質含有情況標示聲明書產品元件名稱 PCB 外殼鉛 Pb 鎘 Cd ○ ○ ○ ○ 限用物質及其化學符號汞 Hg 六價鉻 CrVI 多溴聯苯 PBB 多溴二苯醚 PBDE ○ ○ ○ ○ ○ ○ ○ ○ 備考1. "超出0.1 wt %" 及 "超出0.01 wt %" 系指限用物質之百分比含量超出百分比含量基準值. 備考2."○"系指該項限用物質之百分比含量未超出百分比含量基準值.
PAGE 23
Explanation of the symbols on the product label Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbol Explanation Class II equipment AC voltage Indoor use only. Polarity of output terminals Energy efficiency marking (Level VI) RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE).