NC220 Day/Night Cloud Camera, 300Mbps Wi-Fi NC230 HD Day/Night Wi-Fi Cloud Camera NC250 HD Day/Night Cloud Camera, 300Mbps Wi-Fi 1910012149 REV1.1.
COPYRIGHT & TRADEMARKS is a registered trademark of Specifications are subject to change without notice. TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2017 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
RF Exposure Information This device meets the EU requirements (1999/5/EC Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSSs.
BSMI Notice 安全諮詢及注意事項 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 注意防潮，請勿將水或其他液體潑灑到本產品上。 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
Explanation of the symbols on the product label Symbol Explanation DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
CONTENTS Chapter 1 About This Guide ................................................................................... 1 1.1 1.2 Conventions................................................................................................................... 1 Overview of This Guide ................................................................................................. 1 Chapter 2 Get to Know Your Camera ..................................................................... 3 2.1 2.2 2.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Chapter 1 About This Guide This User Guide contains information for setup and management of the Cloud Camera. When using this guide, please notice that features may vary slightly depending on the model and software version you have, and on your location, and language. All images, parameters and descriptions documented in this guide are used for demonstration only. 1.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Chapter Introduction Chapter 4 Configure Your Camera Introduces how to configure the camera using the built-in web management page.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Chapter 2 Get to Know Your Camera 2.1 Product Overview TP-LINK Cloud Camera is a versatile solution for home and office monitoring to keep an eye on your home, kids or workplace, whatever you care for most.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Wireless connectivity compliant with WPS button Instantly eliminates the dead zones and expand your home’s wireless network Ethernet port for wired connectivity 4x digital zoom for close-up viewing Advanced H.264 video compression for smooth video streaming Support wireless 802.11b/g/n 2.3 Panel Appearance 2.3.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi System LED: Status Flashing Red Solid Red Flashing Green Solid Green Indication The camera starts booting up. The camera has boot up, but is not connected to any network. The camera is in firmware upgrade procedure. The camera is connected to a network or is transferring data. 2.3.
NC220 NC230 NC250 Solid Green Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi The camera has been successfully added to a network by WPS function. This process will last in the first 2 minutes. Ethernet Port: The ethernet port is used to connect the camera to a network via RJ45 cable. Power Jack: The power jack is where you connect the power adapter to the camera. WPS/RESET Button: This button is used for both WPS and RESET function.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Chapter 3 Set Up Your Camera 3.1 Set up the Camera with the tpCamera App You can install your camera in minutes with the free tpCamera app. If your router has a WPS button, you can complete the setup wirelessly using WPS function. Please follow the steps below to set up your camera. Step 1. Connect the camera to the network your smartphone is on.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Step 2. Download and install the tpCamera app. You can download the free tpCamera app from the App Store or Google Play. You can also scan the QR code below to download the tpCamera app. OR Step 3. Add the camera to your TP-LINK cloud account. Launch the tpCamera app, log in with your TP-LINK cloud account or create one if you do not have an account.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 1. Unscrew the camera head. 2. Remove the base cover. 3. Use two screws (not included) to secure 4. Put the base cover and camera head back the base. on. After relocating your camera, face it towards the area you’d like to view, and then plug the power adapter into a power outlet.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Chapter 4 Configure Your Camera You can use the tpCamera app and TP-LINK Cloud (http://www.tplinkcloud.com) to view and manage your camera remotely. To configure the camera’s settings, such as the network settings, cloud settings, notification delivery, you should use the camera’s built-in web management page in your local network. 4.1 1.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 4. Enter the default username and password (admin/admin). Click Login. 5. Create a new password for your camera to enhance security. Click OK. Note: For the administrator, the default password is “admin”. For subsequent logins, use your password you have created. If you log in to the camera as an administrator, you can perform all the settings provided by the camera.
NC220 NC230 NC250 Symbols Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Meaning Note Click to capture a still image shot by the camera. The image file will be saved to your local computer. You can select a save path and rename the image file. Click to rotate the current image. If the camera is installed upside down, Rotate Image should be checked.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Saturation: Drag the slider to adjust the saturation level of the camera. Large value will saturate the current displayed screen to be more colorful. 4.3 Preset: Click the Preset button to restore to factory image settings. Basic Click the Basic menu to display the submenus including Status, Network, Wireless Connection, Cloud Setting, and LED. 4.3.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 14
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 4.3.2 Basic > Network On this page, you can configure your camera’s IP address which is used to access and configure the camera. Dynamic IP: Select this option when a DHCP server is installed on the network to issue IP address assignment. With this setting, the IP address of the camera is assigned automatically.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Primary DNS Server: Enter a DNS address in dotted-decimal notation. Secondary DNS Server: Enter a DNS address in dotted-decimal notation. Click Save to save and enable the settings. 4.3.3 Basic > Wireless Connection The camera’s wireless function is enabled by default. This function helps to connect your camera to a wireless network wirelessly.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi To connect your camera to a wireless network, follow the steps below: 1. Click Scan to scan the available wireless network and to refresh the Wireless Network List. 2. Select a wireless network from the wireless network list. 3. If the wireless network’s security mode is None, simply click Connect.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 5. Click OK on the pop–up screen to finish wireless connection procedure. 6. To start using camera wirelessly, unplug its Ethernet cable. 4.3.4 Basic > Cloud Setting A Cloud Camera can be viewed anytime and anywhere over the Internet with TP-LINK Cloud service. On this page, you can add the camera to your TP-LINK Cloud account. Note: 1.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Account: Enter your TP-LINK Cloud account, either E-mail address or username is allowed. Password: Enter your TP-LINK Cloud account’s password. Camera Name: The default value is the camera model. You can change it to an easy-to-remember one. Camera name can contain up to 31 characters. It cannot contain the following characters: \ / : = & ‘ “ < > { }.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 4.4.1 Advanced > Status Refer to 4.3.1 Basic > Status. 4.4.2 Advanced > Network On this page, you can configure the network settings of the camera.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi On this section, you can configure your camera’s IP address which is used to access and configure the camera. Dynamic IP: Select this option when a DHCP server is installed on the network to issue IP address assignment. With this setting, the IP address of the camera is assigned automatically.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Primary DNS Server: Enter a DNS address in dotted-decimal notation. Secondary DNS Server: Enter a DNS address in dotted-decimal notation. HTTP (Hypertext Transfer Protocol) This feature allows you to access and manage your camera via its IP address. Web browser access normally uses the standard HTTP service port 80. The camera uses HTTP port 80 by default.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi On this page, you can either scan a wireless network to connect to or enter a wireless network’s parameters manually. To scan a wireless network, refer to 4.3.3 Basic > Wireless Connection. To enter the parameters manually, see the following. 1. Select Enable to enable your camera’s wireless function. 2. Click Manually, and you will see the following screen. 3.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Note: The name must be exactly the same as that used in the wireless access point, or the connection will not be established. Leaving this field blank means the camera will attempt to access the nearest open network. If your PC wants to access the camera, make sure your PC and the camera are connecting to the same wireless network. 4.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Same as Host: The extended network will use the same name and settings as your Host network. Your devices can use the same wireless information to connect to both the host and extended networks. Create a New One: Select this to manually set the name and security used for the extended network.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Coding Format: Displays the video coding format of the camera. Resolution: Displays the video resolution of the camera. Higher resolution offers better quality, but will require more bandwidth to stream. Frame Rate: Select the frame rate to use for the video stream from the drop-down list. Higher settings offer smoother video streams, but will require more bandwidth.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Time Stamp&On-Screen Display (OSD): If enabled, the current time of your camera, which can be set on the System > Date/Time page, will be displayed on the Live View screen. Meanwhile, you can set the OSD text to be displayed with the time stamp. The OSD text is camera name by default. Enabled Disabled 2015-05-10 09:51:21 NC250 Click Save to save and enable the settings. 4.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Motion Detection: To enable or disable the motion detection function. The area with blue mask indicates that it is the area with motion detection on. All areas are selected by default. You can drag your mouse to draw specific areas that you want to monitor. Sensitivity: Specify the level of difference between two sequential images that would indicate motion.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Sound Detection: To enable or disable the sound detection function. Sensitivity: Specify the level of difference between current sound and the threshold you set. Select one of the three levels of sensitivity from the drop-down list: High, Medium, and Low. Threshold: Select the threshold of sound level.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi FTP Select FTP, you can configure your camera to send snapshots to a specified FTP sever on the following screen: FTP Server/ Port: Enter the IP or the domain (IP/domain without prefix ftp://) and the port of the FTP server that you will be connecting to. The port is 21 by default. Note: The FTP server you set and the camera should be in the same LAN.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 1. Enter an IP address or domain of your FTP server, e.g. 192.168.1.168 2. Remain the FTP port number as the default value: 21. 3. Enter your username to log in to the FTP server, e.g. test. 4. Enter your password to log in to the FTP server. 5. Enter the path to the destination on the FTP server, e.g. /test 6. Enable Passive Mode. 7.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Recipient E-mail Address: Enter the receiver’s E-mail address that the notification E-mail will be sent to. Click Add recipient to add receiver’s E-mail addresses. You can specify up to four recipient E-mail addresses. Sender E-mail Address: Enter the sender’s E-mal address that is used to send the notification E-mail.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 1. Enter the receiver’s E-mail address in Recipient E-mail Address, e.g. test@tp-link.com. 2. Enter your E-mail address in Sender E-mail Address, e.g. test@gmail.com. 3. Enter the password required to access the SMTP server. 4. Enter smtp.gmail.com in SMTP server. 5. Select TLS as the SSL encryption and the SMPT server port number will be changed to 465 automatically.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 4.5.1 Account On this page, you can change the administrator’s password and manage the user account(s) that are allowed to access to your camera. Username: Displays the name of user account. User Group: Displays the group that the user account is in. Different user group has different limits of authority. admin: This group has all authority of configuration.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 2. Enter a username for your new account. 3. Enter a password for your new account. The password should contain 5 to 20 characters. 4. Enter the password again to confirm it. 5. Click Save to save and enable the settings. Change Password You can change the password of all the accounts here. Note: The default account and password are both admin.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi 3. Enter the current password in the Old Password textbox. 4. Enter a new password. 5. Enter the new password again to confirm it. 6. Click Save to save and enable the settings. Delete a User Account You can delete a user account except admin here. Click a user entry in the list and click Delete. 4.5.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Current Time: Displays the current date and time of the camera. Time Zone: Select the time zone for the region where the camera is installed. Synchronize With NTP Server: Select this option to specify the NTP server name to synchronize the date and time of the camera with those of the time server, known as the NTP (Network Time Protocol) server.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Copy Your Computer’s Time Settings: Click this button to copy your computer’s current time settings. Click Save to save and enable the settings. 4.5.3 Management On this page, you can reboot the camera, backup and restore the camera’s current settings, reset factory settings, and update the camera’s software.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Backup: Click Backup and follow the instructions on the browser to save the setting data file to your specified location. Restore: Click Browse to locate the saved backup file and then click Restore. The camera will start rebooting and then the settings will be restored to the previous configuration.
NC220 NC230 NC250 Day/Night Cloud Camera, 300Mbps Wi-Fi HD Day/Night Wi-Fi Cloud Camera HD Day/Night Cloud Camera, 300Mbps Wi-Fi Time: Displays the time when the log event occurs. The log can get the correct time after you configure on the Date/Time page. (go to Advanced > Date/Time) Module: Displays the module to which the log information belongs. You can specify the module by selecting one from the Module drop-down list at the bottom. Level: Displays the severity level of the log information.
