TL-WR700N 150Mbps Wireless N Mini Pocket Router Rev: 1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device.
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即 停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射 頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。 安全諮詢及注意事項 ●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ●注意防潮，請勿將水或其他液體潑灑到本產品上。 ●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 ●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актам
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N Mini Pocket Router Model No.
CONTENTS Package Contents..................................................................................................................................1 Chapter 1. Introduction .......................................................................................................................2 1.1 Overview of the Router .......................................................................................................2 1.2 Conventions ...........................................................
4.7 4.8 4.9 4.6.1 Wireless Settings ..................................................................................................34 4.6.2 Wireless Security ..................................................................................................37 4.6.3 MAC Filtering ........................................................................................................39 4.6.4 Wireless Advanced .........................................................................................
4.14 System Tools .....................................................................................................................69 4.14.1 Time ......................................................................................................................70 4.14.2 Diagnostic .............................................................................................................71 4.14.3 Firmware ...............................................................................................
6.1 Login .................................................................................................................................94 6.2 Status ................................................................................................................................94 6.3 Quick Setup.......................................................................................................................96 6.4 Working Mode ...................................................................
7.7.3 7.8 Address Reservation ......................................................................................... 121 System Tools .................................................................................................................. 122 7.8.1 Diagnostic .......................................................................................................... 122 7.8.2 Firmware ............................................................................................................
8.8.6 Password ........................................................................................................... 151 8.8.7 System Log ........................................................................................................ 151 Appendix A: FAQ .............................................................................................................................. 153 Appendix B: Configuring the PC .............................................................................
TL-WR700N 150Mbps Wireless N Mini Pocket Router Package Contents The following items should be found in your package: One TL-WR700N 150Mbps Wireless N Mini Pocket Router Quick Installation Guide One RJ-45 Ethernet Cable One Resource CD for TL-WR700N 150Mbps Wireless N Mini Pocket Router, including: • User Guide • Other Helpful Information Note: Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact with your distributor.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Chapter 1. Introduction 1.1 Overview of the Router Small enough to fit in the average pocket, the TL-WR700N 150Mbps Wireless N Mini Pocket Router is uniquely suited to provide robust wireless networking to travelers, students, or anyone else for work or play. Incredible Speed TL-WR700N supports the newest 802.11n standards, and provides backward compatibility with older 802.11b/g standards as well.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 1.2 Conventions The Router or TL-WR700N mentioned in this guide stands for TL-WR700N 150Mbps Wireless N Mini Pocket Router without any explanation. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand. 1.3 Main Features Complies with IEEE 802.
TL-WR700N 150Mbps Wireless N Mini Pocket Router LED Status Solid Blue Blinking Indication The device is working properly. The system is booting. Please wait 15 seconds. The device is unable to connect to the network. Table 1-1 The LED Description Note: For Repeater/ Bridge/ Client mode, the LED may blink for up to 3 minutes. If the devices blink for more than 3 minutes, please verify that the password is entered correctly.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Chapter 2. Connecting the Router 2.1 System Requirements Each PC in the LAN needs a working Ethernet Adapter TCP/IP protocol must be installed on each PC Web browser, such as Microsoft Internet Explorer 5.
TL-WR700N 150Mbps Wireless N Mini Pocket Router On this mode, the only wired port works as WAN, which can be connected to DSL Modem with an Ethernet cable. Computers could connect to the device by only wireless way. Figure 2-1 Hardware Installation of the TL-WR700N in Router Mode 1. Connect the WAN port of TL-WR700N to the LAN Port on the DSL/Cable Modem. 2. Connect the WAN port on the DSL/Cable Modem to the wired Internet. 3. Plug the power plug of TL-WR700N in electrical wall socket. 4.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 2-2 Hardware Installation of the TL-WR700N in Repeater Mode 1. Plug the power plug of TL-WR700N in electrical wall socket. 2. Power on the notebook(s). Note: It is recommended that you connect a PC/notebook to the LAN port of the Router with an Ethernet cable, and then login the Router from the PC/notebook to set the Router in AP Repeater mode. 2.3.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 1. Plug the power plug of TL-WR700N in electrical wall socket. 2. Power on the notebook(s). Note: It is recommended that you connect a PC/notebook to the LAN port of the Router with an Ethernet cable, and then login the Router from the PC/notebook to set the Router in Bridge mode. 2.3.4 Client Mode TL-WR700N is used as a wireless network card to connect the wireless network signal or wireless router. On this mode, the only wired port works as LAN.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Note: The Device is equipped with Smart IP function, which would help to enable its built-in DHCP server when it’s required. For your convenience, please configure your PC or other clients to “Obtain an IP address automatically”. If you need any instructions as how to do this, please refer to Appendix B: "Configuring the PC”. Figure 2-5 Hardware Installation of the TL-WR700N in AP Mode 1.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TL-WR700N 150Mbps Wireless N Mini Pocket Router using Quick Setup Wizard within minutes. With a Web-based utility, it is easy to configure and manage the TL-WR700N 150Mbps Wireless N Mini Pocket Router.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 3-2 Quick Setup - Working Mode Note: The Router supports five working modes for multi-user to access the Internet: Router, Repeater, Bridge, Client and AP. In Router mode, TL-WR700N can access the Internet via DSL/Cable Modem. In Repeater mode, the device will relay data to an associated root AP. In Bridge mode, the device bridges to another AP. In Client mode, the device will act as a wireless station to enable wired host(s) to access AP.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Wireless Network Name (SSID) - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive.
TL-WR700N 150Mbps Wireless N Mini Pocket Router The Router supports three popular ways Dynamic IP, PPPoE and Static IP to connect to the Internet. To make sure the connection type your ISP provides, please refer to the ISP. Make sure the cable is securely plugged into the WAN port before detection. Dynamic IP - Your ISP uses a DHCP service to assign your Router an IP address for connecting to the Internet.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 3-7 Quick Setup – Finish 3.1.2 Repeater Mode When you choose Repeater Mode on Working Mode page in Figure 3-2 , take the following steps: 1. Wait a few minutes when the device is detecting the surrounding wireless networks. Figure 3-8 2. Choose the wireless network you would like to extend from the list available, and then click Next.
TL-WR700N 3. 150Mbps Wireless N Mini Pocket Router Input the wireless password of the wireless network you’ve chosen, and then click Next. Figure 3-10 4. The Finish page is shown as Figure 3-11. Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup. Figure 3-11 3.1.3 Bridge Mode When you choose Bridge on Working Mode page in Figure 3-2 , take the following steps: 1. Wait a few minutes when the device is detecting the surrounding wireless networks.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 3-13 3. Input the wireless password of the wireless network you’ve chosen, and then click Next. Figure 3-14 4. Set the wireless parameters for the network created by TL-WR700N, or you can keep them default, and then click Next.
TL-WR700N 5. 150Mbps Wireless N Mini Pocket Router The Finish page is shown as Figure 3-16. Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup. Figure 3-16 3.1.4 Client Mode When you choose Client on Working Mode page in Figure 3-2 , take the following steps: 1. Wait a few minutes when the device is detecting the surrounding wireless networks. Figure 3-17 2.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 3-19 4. The Finish page is shown as Figure 3-20. Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup. Figure 3-20 3.1.5 AP Mode When you choose AP on Working Mode page in Figure 3-2 , take the following steps: 1. Set the required wireless parameters on the page (as shown in Figure 3-21), and then click Next.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Wireless Network Name (SSID) - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Note: The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router. Near the center of the area in which your wireless stations will operate. In an elevated location such as a high shelf. Away from the potential sources of interference, such as PCs, microwaves, and cordless phones. Away from large metal surfaces.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Chapter 4. Configuration for Router Mode This chapter will show each Web page's key functions and the configuration way for Router Mode of TL-WR700N. 4.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-2 Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • MAC Address - The physical address of the Router, as seen from the LAN. • IP Address - The LAN IP address of the Router. • Subnet Mask - The subnet mask associated with LAN IP address. Wireless - This field displays basic information or status for wireless function, you can configure them in the Wireless > Wireless Settings page. • Wireless Mode - The current wireless working mode in use.
TL-WR700N 150Mbps Wireless N Mini Pocket Router System Up Time - The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 4.3 Quick Setup Please refer to Section 3.2.1. 4.4 Working Mode The Router supports five operation mode types: Router, Repeater, Bridge, Client and AP. Please select the mode you want. Click Save to save your choice, which is shown as Figure 4-3.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4.5 Network Figure 4-5 the Network menu There are three submenus under the Network menu (shown in Figure 4-5): WAN, LAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function. 4.5.1 WAN Choose menu “Network → WAN”, and then you can configure the IP parameters of the WAN on the screen below. 1.
TL-WR700N 150Mbps Wireless N Mini Pocket Router This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Default Gateway - Enter the gateway IP address in dotted-decimal notation provided by your ISP. MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP. Primary DNS / Secondary DNS (Optional) - Enter one or two DNS addresses in dotted-decimal notation provided by your ISP. Click the Save button to save your settings.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Dynamic IP - You can check this radio button to use Dynamic IP as the secondary connection to connect to the local area network provided by ISP. • Static IP - You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-9 PPPoE Advanced Settings MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. Service Name/AC Name - The service name and AC (Access Concentrator) name should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-10 WAN – L2TP/Russia L2TP User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, check the radio button.
TL-WR700N 150Mbps Wireless N Mini Pocket Router User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4.5.2 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 4-12 LAN MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed. IP Address - Enter the IP address of your Router in dotted-decimal notation (factory default: 192.168.0.254). Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.
TL-WR700N 150Mbps Wireless N Mini Pocket Router WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XX-XX format (X is any hexadecimal digit). Your PC's MAC Address - This field displays the MAC address of the PC that is managing the Router.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-15 Wireless Settings - Router SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 802.11b/g/n, and all of 802.11b, 802.11g, and 802.11n wireless stations can connect to the Router. Channel Width - Select any channel width from the pull-down list. The default setting is automatic, which can automatically adjust the channel width for your clients. Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the wireless router will broadcast its name (SSID) on the air. Enable WDS - You can select to enable WDS.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Note: 1. The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router. Near the center of the area in which your wireless stations will operate. In an elevated location such as a high shelf. Away from the potential sources of interference, such as PCs, microwaves, and cordless phones. Away from large metal surfaces. 2.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security. WEP - It is based on the IEEE 802.11 standard. • Type - you can choose the type for the WEP security on the pull-down list.
TL-WR700N 150Mbps Wireless N Mini Pocket Router WPA-PSK/WPA2-PSK- It’s the WPA/WPA2 authentication type based on pre-shared passphrase. • Version - you can choose the version of the WPA-PSK security on the drop-down list. The default setting is Automatic (Recommended), which can select WPA-PSK (Pre-shared key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request.
TL-WR700N 150Mbps Wireless N Mini Pocket Router To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address - The wireless station's MAC address that you want to access. Status - The status of this entry, either Enabled or Disabled. Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button.
TL-WR700N 150Mbps Wireless N Mini Pocket Router For example: If you desire that the wireless station A with MAC address 00-0A-EB-B0-00-0B and the wireless station B with MAC address 00-0A-EB-00-07-5F are able to access the Router, but all the other wireless stations cannot access the Router, you can configure the Wireless MAC Address Filtering list by following these steps: 1. Click the Enable button to enable this function. 2.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-20 Wireless Statistics MAC Address - The connected wireless station's MAC address Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected Received Packets - Packets received by the station Sent Packets - Packets sent by the station You cannot change any of the values on this page.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-22 DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4.7.2 DHCP Clients List Choose menu “DHCP → DHCP Clients List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 4-23. Figure 4-23 DHCP Clients List Client Name - The name of the DHCP client MAC Address - The MAC address of the DHCP client Assigned IP - The IP address that the Router has allocated to the DHCP client Lease Time - The time of the DHCP client leased.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Status - The status of this entry, either Enabled or Disabled. To Reserve an IP address: 1. Click the Add New… button. Then will pop-up. 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address. 3. Click the Save button. Figure 4-25 Add or Modify an Address Reservation Entry To modify or delete an existing entry: 1.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4.8.1 Virtual Servers Choose menu “Forwarding → Virtual Servers”, and then you can view and add virtual servers in the screen as shown in Figure 4-27. Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and FTP. A virtual server is defined as a service port, and all requests from the Internet to this service port will be redirected to the computer specified by the server IP.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-28 Add or Modify a Virtual Server Entry Note: If your computer or server has more than one type of available service, please select another service, and enter the same IP Address for that computer or server. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-29 Port Triggering Once the Router is configured, the operation is as follows: 1. A local host makes an outgoing connection using a destination port number defined in the Trigger Port field. 2. The Router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. 3.
TL-WR700N 5. Select Enable in Status field. 6. Click the Save button to save the new rule. 150Mbps Wireless N Mini Pocket Router Figure 4-30 Add or Modify a Port Triggering Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button. Click the Enable All button to make all entries enabled. Click the Disable All button to make all entries disabled.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-31 DMZ To assign a computer or server to be a DMZ server: 1. Check the Enable radio button. 2. Enter the IP Address of a local host in the DMZ Host IP Address field. 3. Click the Save button. Note: After you set the DMZ host, the firewall related to the host will not work. 4.8.4 UPnP Choose menu “Forwarding → UPnP”, and then you can view the information about UPnP (Universal Plug and Play) in the screen as shown in Figure 4-32.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Protocol - The type of protocol the Router opens for the application. • Internal Port - The Internal port the Router opens for local host. • IP Address - The IP address of the UPnP device that is currently accessing the Router. • Status - The status of the port is displayed here. “Enabled” means that the port is still active. Otherwise, the port is inactive. Click Refresh to update the Current UPnP Settings List. 4.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Enable Firewall - the general firewall switch is on or off. Enable IP Address Filtering - set IP Address Filtering is enabled or disabled. There are two default filtering rules of IP Address Filtering, either Allow or Deny passing through the router. Enable Domain Filtering - set Domain Filtering is enabled or disabled. Enable MAC Filtering - set MAC Address Filtering is enabled or disabled.
TL-WR700N 150Mbps Wireless N Mini Pocket Router To create or modify an IP Address Filtering entry, please follow these instructions: 1. Effective Time - Enter a range of time in HHMM format, which point to the range time for the entry to take effect. For example, 0803 - 1705, the entry will take effect from 08:03 to 17:05. 2. LAN IP Address - Enter a LAN IP Address or a range of LAN IP addresses in the field, in dotted-decimal notation format. For example, 192.168.0.20 - 192.168.0.30.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4.9.3 Domain Filtering The Domain Filtering page allows you to control access to certain websites on the Internet by specifying their domains or key words. Figure 4-37 Domain Filtering Before adding a Domain Filtering entry, you must ensure that Enable Firewall and Enable Domain Filtering have been selected on the Firewall page. To Add a Domain filtering entry, click the Add New… button.
TL-WR700N 2. Modify the information. 3. Click the Save button. 150Mbps Wireless N Mini Pocket Router Click the Enable All button to make all entries enabled. Click the Disable All button to make all entries disabled. Click the Delete All button to delete all entries Click the Next button to go to the next page and the Previous button to return to the previous page. For example: if you want to block the PC(s) on your LAN to access websites www.xxyy.com.cn, www.aabbcc.com and websites with .
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-40 Add or Modify a MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0E-AE-B0-00-0B. 2. 3. 4. Type the description of the PC in the Description field. Fox example: John’s PC.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4.9.5 Remote Management You can configure the Remote Management function on this page. This feature allows you to manage your Router from a remote location, via the Internet. Figure 4-41 Remote Management Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router’s default remote management Web port number is 80.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-42 Advanced Security settings Packets Statistic interval (5 ~ 60) - The default value is 10. Select a value between 5 and 60 seconds in the pull-down list. The Packets Statistic interval value indicates the time section of the packets statistic. The result of the statistic used for analysis by SYN Flood, UDP Flood and ICMP-Flood. DoS protection - Enable or Disable the DoS protection function.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Ignore Ping Packet from WAN Port - Enable or Disable ignore ping packet from WAN port. The default is disabled. If enabled, the ping packet from the Internet cannot access the router. Forbid Ping Packet from LAN Port - Enable or Disable forbidding Ping Packet to access the router from the LAN port. The default value is disabled. If enabled, the ping packet from the LAN port cannot access the router.
TL-WR700N 150Mbps Wireless N Mini Pocket Router To add static routing entries: 1. Click the Add New button. 2. Enter the following data: Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route. Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-46 IP QoS Enable IP QoS - Enable or disable the function of IP QoS. Choose BandWidth Type - Select the network connection type from the drop-down list. Bandwidth Apply - The bandwidth you get. If you are not clear about that, please contact with your ISP for help. IP Range - IP range of this entry. Mode - There are two types of mode: Minimum Bandwidth Guarantee and Maximum Bandwidth Limit.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4. IP address range for different entries could not have intersection with each other. 5. After the configurations, click the Save button for the change to take effect. 4.12 IP & MAC Binding Setting Figure 4-47 the IP & MAC Binding menu There are two submenus under the IP & MAC Binding menu: Binding Setting and ARP List. Click any of them, and you will be able to scan or configure the corresponding function.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-49 IP & MAC Binding Setting (Add & Modify) To add IP & MAC Binding entries: 1. Click the Add New... button. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4. Click the Save button to save it. To modify or delete an existing entry: 1. Find the desired entry in the table. 2. Click Modify or Delete as desired on the Modify column. To find an existing entry: 1. Click the Find button (shown in Figure 4-48). 2.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4.12.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could configure the items on the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding entries. Figure 4-51 ARP List MAC Address - The MAC address of the controlled computer in the LAN.
TL-WR700N 150Mbps Wireless N Mini Pocket Router service providers such as www.oray.net, www.comexe.cn, www.dyndns.org, or www.no-ip.com. The Dynamic DNS client service provider will give you a password or key. 4.13.1 No-IP DDNS If the dynamic DNS Service Provider you select is www.no-ip.com, the page will appear as shown in Figure 4-52. Figure 4-52 No-IP DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-53 PeanutHull DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the User Name for your DDNS account. 2. Enter the Password for your DDNS account. 3. Click the Login button to login to the DDNS service. Connection Status - The status of the DDNS service connection is displayed here. Service Type - The type of service is displayed here. Domain Name - The domain names are displayed here.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 4-54 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Type the Domain Name received from your dynamic DNS service provider. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service.
TL-WR700N Figure 4-55 150Mbps Wireless N Mini Pocket Router Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider here. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to logout of the DDNS service.
TL-WR700N 150Mbps Wireless N Mini Pocket Router There are nine submenus under the System Tools menu: Time, Diagnostic, Firmware, Factory Defaults, Backup & Restore, Reboot, Password, System Log and Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.14.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4.14.2 Diagnostic Choose menu “System Tools → Diagnostic”, you can transact Ping or Traceroute function to check connectivity of your network in the following screen. Figure 4-58 Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic too. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Ping Packet Size - The size of Ping packet. Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. Traceroute Max TTL - The max number of hops for a Traceroute connection. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis.
TL-WR700N 150Mbps Wireless N Mini Pocket Router To upgrade the Router's firmware, follow these instructions below: 1. Download a more recent firmware upgrade file from the TP-LINK website (http://www.tp-link.com). 2. Type the path and file name of the update file into the File field, or click the Browse… button to locate the update file. 3. Click the Upgrade button. Note: 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 4.14.5 Backup & Restore This page allows you to save current configuration of router as backup or restore the configuration file you saved before. Figure 4-62 Backup & Restore Configuration Click the Backup button to save all configuration settings as a backup file in your local computer. To restore the router's configuration, follow these instructions: • Click the Browse… button to select the backup file which you want to restore.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Upgrade the firmware of the router (system will reboot automatically). Restore the router's settings to factory default (system will reboot automatically). 4.14.7 Password This page allows you to change the factory default user name and password of the router. Figure 4-64 Password It is recommended strongly that you change the factory default user name and password of the router.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Click the Clear All button to clear all the logs. 4.14.9 Statistics The Statistics page displays the network traffic of each PC in LAN, including total traffic and traffic of the last Packets Statistic interval seconds. Figure 4-66 Statistics Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button. If disabled, the function of DoS protection in Security settings will be ineffective.
TL-WR700N TCP SYN Tx 150Mbps Wireless N Mini Pocket Router The total amount of the TCP SYN packets transmitted to WAN in the last Packets Statistic interval seconds. Click the Save button to save the Packets Statistic interval value. Click the Auto-refresh checkbox to refresh automatically. Click the Refresh button to refresh immediately.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Chapter 5. Configuration for Repeater Mode This chapter will show each Web page's key functions and the configuration way for Repeater Mode of TL-WR700N. 5.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 5-2 Status Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. Connection Status to Main Router/AP Wi-Fi Network - This part shows you the current information of the Main Router/AP Wi-Fi network which the device is connecting to. • Main Router/AP Wi-Fi Network - It shows the name of the wireless network which your device is connecting to.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Wireless Mode - The current wireless working mode in use. • Name (SSID) - The SSID of Root AP. • Channel - The current wireless channel in use. • MAC address - The physical address of the Router, as seen from the WLAN. System Up Time - The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 5.3 Quick Setup Please refer to Section 3.2.2. 5.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 5-4 5.5 Network Figure 5-5 the Network menu There is only one submenu under the Network menu (shown in Figure 5-5): LAN. 5.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 5-6 LAN Address Type - Choosing Smart IP to get IP address from DHCP server, or choosing Static IP to configure IP address manually.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 2. If you select the type of Smart IP (DHCP) and there is a DHCP server forward, the DHCP server in this device will not start up. 3. If the new LAN IP address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automatically, but the Virtual Server and DMZ Host will not take effect until they are re-configured. 5.
TL-WR700N 150Mbps Wireless N Mini Pocket Router the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. Survey - Click this button, you can search the AP which runs in the environment. Security Options - This option should be chosen according to the security configuration of the AP you want to access. It is recommended that the security type is the same as your AP’s security type.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 5.7.1 DHCP Settings Selecting DHCP > DHCP Settings will enable you to set up the Range Extender as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs that are connected to the system on the LAN. The DHCP Server can be configured on the page (shown as Figure 5-11), only when you’ve set the Network LAN type as Static IP in Figure 5-6.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Server, you must have another DHCP server within your network or else you must manually configure the computer. Start IP Address - This field specifies the first address in the IP Address pool. 192.168.0.100 is the default start IP address. End IP Address - This field specifies the last address in the IP Address pool. 192.168.0.199 is the default end IP address.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 5-12 DHCP Clients List Client Name - The name of the DHCP client MAC Address - The MAC address of the DHCP client Assigned IP - The IP address that the Router has allocated to the DHCP client Lease Time - The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page.
TL-WR700N 2. 150Mbps Wireless N Mini Pocket Router Enter the MAC address (in XX-XX-XX-XX-XX-XX format) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address. 3. Click the Save button. Figure 5-14 Add or Modify an Address Reservation Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 5.8.1 Diagnostic Choose menu “System Tools → Diagnostic”, and then you can transact Ping or Traceroute function to check connectivity of your network in the following screen. Figure 5-16 Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. The default is 800. Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis.
TL-WR700N 5. 150Mbps Wireless N Mini Pocket Router Type the path and file name of the update file into the File field, or click the Browse… button to locate the update file. 6. Click the Upgrade button. Note: 5. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 5.8.4 Backup & Restore Choose menu “System Tools → Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 5-20. Figure 5-20 Backup & Restore Configuration Click the Backup button to save all configuration settings as a backup file in your local computer. To upgrade the Router's configuration, follow these instructions.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (system will reboot automatically). • Update the configuration with the file (system will reboot automatically. 5.8.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 5.8.7 System Log Choose menu “System Tools → System Log”, and then you can view the logs of the Router. Figure 5-23 System Log Refresh - Refresh the page to show the latest log list. Clear All - All the logs will be deleted from the Router permanently, not just from the page.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Chapter 6. Configuration for Bridge Mode This chapter will show each Web page's key functions and the configuration way for Bridge Mode of TL-WR700N. 6.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 6-2 Status Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. Connection Status to Main Router/AP Wi-Fi Network - This part shows you the current information of the Main Router/AP Wi-Fi network which the device is connecting to. • Main Router/AP Wi-Fi Network - It shows the name of the wireless network which your device is connecting to.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Wireless Mode - The current wireless working mode in use. • Wireless Radio - Indicates whether the wireless radio feature of the AP is enabled or disabled. • Name (SSID) - The SSID of the AP. • Channel - The current wireless channel in use. • MAC Address - The physical address of the Router, as seen from the WLAN. System Up Time - The length of the time since the Router was last powered on or reset.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 6-4 6.5 Network Figure 6-5 the Network menu There is only one submenu under the Network menu (shown in Figure 6-5): LAN. 6.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 6-6 LAN Address Type - Choosing Smart IP to get IP address from DHCP server, or choosing Static IP to configure IP address manually.
TL-WR700N 150Mbps Wireless N Mini Pocket Router server in this device will not start up. 3. If the new LAN IP address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automatically, but the Virtual Server and DMZ Host will not take effect until they are re-configured. 6.6 Wireless Figure 6-7 Wireless menu There are two submenus under the Wireless menu (shown in Figure 6-7): Wireless Settings and Wireless Security.
TL-WR700N 150Mbps Wireless N Mini Pocket Router name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 6.6.2 Wireless Security Choose menu “Wireless → Wireless Security”, and then you can configure the security settings of your wireless network. There are three wireless security modes supported by the Router: WEP (Wired Equivalent Privacy), WPA/WPA2 and WPA-PSK/WPA2-PSK. Figure 6-9 Wireless Security Disable Security - The wireless security function can be enabled or disabled.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • WEP Key Format - Hexadecimal and ASCII formats are provided here. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length. • WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Encryption - When WPA-PSK or WPA is set as the Authentication Type, you can select Automatic (Recommended), TKIP or AES as Encryption. • PSK Password - You can enter ASCII or Hexadecimal characters. The default password is the last unique eight numbers of each Router’s MAC address For ASCII, the key can be made up of any numbers 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 6-11 DHCP Settings Figure 6-12 DHCP Settings DHCP Server - Selecting the radio button before Disable/Enable will disable/enable the DHCP server on your Range Extender. The default setting is Enable. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer. Start IP Address - This field specifies the first address in the IP Address pool. 192.168.0.
TL-WR700N 150Mbps Wireless N Mini Pocket Router is up, the PC will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. Default Gateway (optional) - Enter the IP address of the gateway for your LAN. The factory default setting is 0.0.0.0. Default Domain (optional) - Enter the domain name of the your DHCP server. You can leave the field blank. Primary DNS (optional) - Enter the DNS IP address provided by your ISP.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 6.7.3 Address Reservation Choose menu “DHCP → Address Reservation”, and then you can view and add a reserved address for clients via the next screen (shown in Figure 6-14).When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings.
TL-WR700N 3. 150Mbps Wireless N Mini Pocket Router Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 6.
TL-WR700N Figure 6-17 150Mbps Wireless N Mini Pocket Router Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. • Traceroute - This diagnostic tool tests the performance of a connection. Note: You can use ping/traceroute to test both numeric IP address or domain name.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 6-18 Diagnostic Results Note: Only one user can use this tool at one time.
TL-WR700N 3. 150Mbps Wireless N Mini Pocket Router Click the Upgrade button. Note: 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware. 2.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 6-21 Backup & Restore Configuration Click the Backup button to save all configuration settings as a backup file in your local computer. To upgrade the Router's configuration, follow these instructions. • Click the Browse… button to locate the update file for the Router, or enter the exact path to the Setting file in the text box. • Click the Restore button. Note: The current configuration will be covered by the uploading configuration file.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Restore the Router's settings to factory defaults (system will reboot automatically). • Update the configuration with the file (system will reboot automatically. 6.8.6 Password Choose menu “System Tools → Password”, and then you can change the factory default user name and password of the Router in the next screen as shown in Figure 6-23.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Refresh - Refresh the page to show the latest log list. Clear All - All the logs will be deleted from the Router permanently, not just from the page.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Chapter 7. Configuration for Client Mode This chapter will show each Web page's key functions and the configuration way for Client Mode of TL-WR700N. 7.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 7-2 Status Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. Connection Status to Main Router/AP Wi-Fi Network - This part shows you the current information of the Main Router/AP Wi-Fi network which the device is connecting to. • Main Router/AP Wi-Fi Network - It shows the name of the wireless network which your device is connecting to.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Channel - The current wireless channel in use. • MAC Address - The physical address of the Router, as seen from the WLAN. System Up Time - The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 7.3 Quick Setup Please refer to Section 3.2.4. 7.4 Working Mode The Router supports five operation mode types: Router, Repeater, Bridge, Client and AP.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 7-4 7.5 Network Figure 7-5 the Network menu There is only one submenu under the Network menu (shown in Figure 7-5): LAN. 7.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 7-6 LAN Address Type - Choosing Smart IP to get IP address from DHCP server, or choosing Static IP to configure IP address manually.
TL-WR700N 150Mbps Wireless N Mini Pocket Router server in this device will not start up. 3. If the new LAN IP address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automatically, but the Virtual Server and DMZ Host will not take effect until they are re-configured. 7.6 Wireless Figure 7-7 Wireless menu There is one submenu under the Wireless menu (shown in Figure 7-7): Wireless Settings.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. Survey - Click this button, you can survey the AP which runs in the current channel.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 7-10 DHCP Settings Figure 7-11 DHCP Settings DHCP Server - Selecting the radio button before Disable/Enable will disable/enable the DHCP server on your Range Extender. The default setting is Enable. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer. Start IP Address - This field specifies the first address in the IP Address pool. 192.168.0.
TL-WR700N 150Mbps Wireless N Mini Pocket Router is up, the PC will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. Default Gateway (optional) - Enter the IP address of the gateway for your LAN. The factory default setting is 0.0.0.0. Default Domain (optional) - Enter the domain name of the your DHCP server. You can leave the field blank. Primary DNS (optional) - Enter the DNS IP address provided by your ISP.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 7.7.3 Address Reservation Choose menu “DHCP → Address Reservation”, and then you can view and add a reserved address for clients via the next screen (shown in Figure 7-13).When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings.
TL-WR700N 3. 150Mbps Wireless N Mini Pocket Router Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 7.
TL-WR700N Figure 7-16 150Mbps Wireless N Mini Pocket Router Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. • Traceroute - This diagnostic tool tests the performance of a connection. Note: You can use ping/traceroute to test both numeric IP address or domain name.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 7-17 Diagnostic Results Note: Only one user can use this tool at one time.
TL-WR700N 3. 150Mbps Wireless N Mini Pocket Router Click the Upgrade button. Note: 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware. 2.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 7-20 Backup & Restore Configuration Click the Backup button to save all configuration settings as a backup file in your local computer. To upgrade the Router's configuration, follow these instructions. • Click the Browse… button to locate the update file for the Router, or enter the exact path to the Setting file in the text box. • Click the Restore button. Note: The current configuration will be covered by the uploading configuration file.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Restore the Router's settings to factory defaults (system will reboot automatically). • Update the configuration with the file (system will reboot automatically. 7.8.6 Password Choose menu “System Tools → Password”, and then you can change the factory default user name and password of the Router in the next screen as shown in Figure 7-22.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Refresh - Refresh the page to show the latest log list. Clear All - All the logs will be deleted from the Router permanently, not just from the page.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Chapter 8. Configuration for AP Mode This chapter will show each Web page's key functions and the configuration way for AP Mode of TL-WR700N. 8.1 Login After your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 8-2 Status Firmware Version - The version information of the Router’s firmware. Hardware Version - The version information of the Router’s hardware. LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. • MAC address - The physical address of the Router, as seen from the LAN. • IP address - The LAN IP address of the Router.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Channel Width - The current wireless channel width in use. • MAC address - The physical address of the Router, as seen from the WLAN. • WDS Status - The status of WDS connection. System Up Time - The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 8.3 Quick Setup Please refer to Section 3.2.5. 8.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 8-4 8.5 Network Figure 8-5 the Network menu There is only one submenu under the Network menu (shown in Figure 8-5): LAN. 8.5.1 LAN Choose menu “Network → LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 8-6 LAN Address Type - Choosing Smart IP to get IP address from DHCP server, or choosing Static IP to configure IP address manually.
TL-WR700N 150Mbps Wireless N Mini Pocket Router server in this device will not start up. 3. If the new LAN IP address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automatically, but the Virtual Server and DMZ Host will not take effect until they are re-configured. 8.
TL-WR700N 150Mbps Wireless N Mini Pocket Router name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field.
TL-WR700N 150Mbps Wireless N Mini Pocket Router SSID (to be bridged) - The SSID of the AP your Router is going to connect to as a client. You can also use the search function to select the SSID to join. BSSID (to be bridged) - The BSSID of the AP your Router is going to connect to as a client. You can also use the search function to select the BSSID to join. Survey - Click this button, you can survey the AP which runs in the current channel.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 2. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Router. 8.6.2 Wireless Security Choose menu “Wireless → Wireless Security”, and then you can configure the security settings of your wireless network. There are three wireless security modes supported by the Router: WEP (Wired Equivalent Privacy), WPA/WPA2 and WPA-PSK/WPA2-PSK.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Type - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. • WEP Key Format - Hexadecimal and ASCII formats are provided here. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.
TL-WR700N 150Mbps Wireless N Mini Pocket Router key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. • Encryption - When WPA-PSK or WPA is set as the Authentication Type, you can select Automatic (Recommended), TKIP or AES as Encryption. • PSK Password - You can enter ASCII or Hexadecimal characters. The default password is the last unique eight numbers of each Router’s MAC address.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 8-11: Figure 8-11 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 1. Click the Enable button to enable this function. 2. Select the radio button “Allow the stations specified by any enabled entries in the list to access” for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New... button. • Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-00-07-5F in the MAC Address field. • Enter wireless station A/B in the Description field.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. RTS Threshold - Here you can specify the RTS (Request to Send) Threshold.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 8-13 Wireless Statistics MAC Address - The connected wireless station's MAC address Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected Received Packets - Packets received by the station Sent Packets - Packets sent by the station You cannot change any of the values on this page.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Note: The DHCP Settings function cannot be configured if you have chosen Smart IP (DHCP) in Network -> LAN, in which situation the device will help you configure the DHCP automatically as you need. The DHCP Settings page will appear as Figure 8-15. Figure 8-15 DHCP Settings Figure 8-16 DHCP Settings DHCP Server - Selecting the radio button before Disable/Enable will disable/enable the DHCP server on your Range Extender. The default setting is Enable.
TL-WR700N 150Mbps Wireless N Mini Pocket Router End IP Address - This field specifies the last address in the IP Address pool. 192.168.0.199 is the default end IP address. Address Lease Time - Enter the amount of time for the PC to connect to the Range Extender with its current assigned dynamic IP address. The time is measured in minutes. After the time is up, the PC will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Lease Time - The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 8.7.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 8-19 Add or Modify an Address Reservation Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 3. Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled Click the Delete All button to delete all entries.
TL-WR700N Figure 8-21 150Mbps Wireless N Mini Pocket Router Diagnostic Tools Diagnostic Tool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. • Traceroute - This diagnostic tool tests the performance of a connection. Note: You can use ping/traceroute to test both numeric IP address or domain name.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20. Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 8-22 Diagnostic Results Note: Only one user can use this tool at one time.
TL-WR700N 150Mbps Wireless N Mini Pocket Router 3. Click the Upgrade button. Note: 1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware. 2.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure 8-25 Backup & Restore Configuration Click the Backup button to save all configuration settings as a backup file in your local computer. To upgrade the Router's configuration, follow these instructions. • Click the Browse… button to locate the update file for the Router, or enter the exact path to the Setting file in the text box. • Click the Restore button. Note: The current configuration will be covered by the uploading configuration file.
TL-WR700N 150Mbps Wireless N Mini Pocket Router • Update the configuration with the file (system will reboot automatically). 8.8.6 Password Choose menu “System Tools → Password”, and then you can change the factory default user name and password of the Router in the next screen as shown in Figure 8-27.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Clear All - All the logs will be deleted from the Router permanently, not just from the page.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Appendix A: FAQ 1. How do I configure the Router to access the Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router. The telephone cord plugs into the Line port of the ADSL Modem. 3) Log in to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu.
TL-WR700N 2. 150Mbps Wireless N Mini Pocket Router How do I configure the Router to access the Internet by Ethernet users? 1) Log in to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking Save. 2) Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem during installation.
TL-WR700N Figure A-4 Figure A-5 150Mbps Wireless N Mini Pocket Router Virtual Servers Add or Modify a Virtual server Entry Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page. 4) How to enable DMZ Host: Log in to the Router, click the “Forwarding” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click Enable radio button and type your IP address into the “DMZ Host IP Address” field, using 192.168.0.
TL-WR700N 4. 150Mbps Wireless N Mini Pocket Router I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the Router, you must change the WEB management port number to avoid interference. 2) To change the WEB management port number: Log in to the Router, click the “Security” menu on the left of your browser, and click "Remote Management" submenu.
TL-WR700N Figure A-9 5. 150Mbps Wireless N Mini Pocket Router Add or Modify a Virtual server Entry The wireless stations cannot connect to the Router. 1) Make sure the "Enable Wireless Router Radio" is checked. 2) Make sure that the wireless stations' SSID accord with the Router's SSID. 3) Make sure the wireless stations have right KEY for encryption when the Router is encrypted.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary. 1. Configure TCP/IP component 1) On the Windows taskbar, click the Start button, and then click Control Panel. 2) Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Figure B-2 5) Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as shown in the Figure below: Figure B-3 - 159 -
TL-WR700N 150Mbps Wireless N Mini Pocket Router Appendix C: Specifications General Standards IEEE 802.11n, 802.11b, 802.11g Protocols TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP Port One 10/100Mbps LAN/WAN port 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) Cabling Type EIA/TIA-568 100Ω STP (maximum 100m) 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) LED SYS Dimensions (L×W×H) 81mm×71mm×28mm Safety & Emissions FCC, CE Wireless Frequency Band 2.4~2.
TL-WR700N 150Mbps Wireless N Mini Pocket Router Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802.
TL-WR700N 150Mbps Wireless N Mini Pocket Router PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection. SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID.
