Enterprise Networking Solution Installation Guide Gigabit Smart Switch TL-SG2216/TL-SG2424/TL-SG2424P/TL-SG2452
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.
Related Document The User Guide and CLI Reference Guide (CLI Reference Guide is not available for TL-SG2452) of the product are provided on the resource CD. To obtain the latest product information, please visit the official website: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during installation. This Installation Guide is structured as follows: Chapter 1 Introduction.
Contents Chapter 1 Introduction————————————— 01 1.1 1.2 Product Overview......................................01 Appearance. .................................................. 01 Chapter 2 Installation— ———————————— 07 2.1 2.2 2.3 2.4 Package Contents......................................07 Safety Precautions.....................................07 Installation Tools.......................................09 Product Installation...................................
Gigabit Smart Switch CCCCCCCCCC Introduction 1111 Product Overview TP-LINK Gigabit Smart Switch, designed for workgroups and departments, provides wire-speed performance and abundant layer 2 management features. It provides a variety of service features and multiple powerful functions with high security. The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks. QoS and IGMP snooping/filtering optimize voice and video application.
Gigabit Smart Switch The front panel of TL-SG2424 is shown as the following figure. Reset LEDs 10/100/1000Mbps RJ45 Port SFP Port FFFFFFFFFFF Front Panel of TL-SG2424 Reset Press this button for five seconds or above to reset the software setting back to factory default settings.
Gigabit Smart Switch The front panel of TL-SG2424P is shown as the following figure. LEDs LED Mode Switch Button Reset 10/100/1000Mbps RJ45 Port SFP Port FFFFFFFFFFF Front Panel of TL-SG2424P LEDs TL-SG2424P has an LED mode switch button which is for switching the LED status indication. When the Speed LED is on, the port LED is indicating the data transmission rate. When the PoE LED is on, the port LED is indicating the power supply status. By default the Speed LED is on.
Gigabit Smart Switch LED PoE Max Status Indication On The remaining PoE power≤7W Flashing The remaining PoE power keeps ≤7W after this LED is on for 2 minutes Off The remaining PoE power≥7W Green 10/100/ 1000Mbps Yellow On The port is supplying power normally Flashing The supply power exceeds the correponding port's maximum power On Overload or short circuit is detected Flashing Power-on self-test has failed Off No PoE power supply is provided on the port LED Mode Switch Button Press
Gigabit Smart Switch LED Status Indication Green On A 1000Mbps device is connected to the corresponding port, but no activity Flashing Data is being transmitted or received On A 10/100Mbps device is connected to the corresponding port, but no activity Flashing Data is being transmitted or received 10/100/ 1000Mbps Yellow Off No device is connected to the corresponding port 10/100/1000Mbps RJ45 Port Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps.
Gigabit Smart Switch The rear panel of TL-SG2424 is shown as the following figure. Grounding Terminal Power Socket FFFFFFFFFFF Rear Panel of TL-SG2424 The rear panel of TL-SG2424P is shown as the following figure. Grounding Terminal Power Socket FFFFFFFFFFF Rear Panel of TL-SG2424P The rear panel of TL-SG2452 is shown as the following figure. Grounding Terminal Power Socket FFFFFFFFFFF Rear Panel of TL-SG2452 Grounding Terminal The Switch already comes with lightning protection mechanism.
Gigabit Smart Switch CCCCCCCCCC Installation 2222 Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord Two mounting brackets and the fittings One Resource CD This Installation Guide 2222 Safety Precautions To avoid any device damage and bodily injury caused by improper use, please observe the following rules.
Gigabit Smart Switch ■■ Site Requirements Temperature/Humidity ȭ ȭ Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table.
Gigabit Smart Switch Lightning Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. ■■ Ensure the rack and device are well earthed. ■■ Make sure the power socket has a good contact with the ground.
Gigabit Smart Switch 2222 Product Installation ■■ Desktop Installation To install the device on the desktop, please follow the steps: 111Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 222Remove the adhesive backing papers from the rubber feet. 333Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device.
Gigabit Smart Switch Rack FFFFFFFFFFF Rack Installation Caution: Please set 5~10cm gaps around the device for air circulation. Please avoid any heavy thing placed on the device. Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation.
Gigabit Smart Switch CCCCCCCCCC Lightning Protection 3333 Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors, please use a signal lightning arrester.
Gigabit Smart Switch ■■ Requirements for Cabling Indoors When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. ■■ ■■ The main cable should be paved in the metal raceway of the access shaft. When cabling, keep the loop area formed by the cable itself as small as possible. Requirements for the distance between Ethernet cable and other pipelines are shown in the table.
Gigabit Smart Switch Cable 2~5kVA powerline >5kVA powerline Pave Way Min Parallel Length (mm1 Parallel cabling 300 One is in the grounded metal raceway or metal pipe 150 The both are in the grounded metal raceway or metal pipe 80 Parallel cabling 600 One is in the grounded metal raceway or metal pipe 300 The both are in the grounded metal raceway or metal pipe 150 Device Min Distance (m1 Switch case 1.00 Transformer room 2.00 Elevator tower 2.00 Air-conditioner room 2.
Gigabit Smart Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. ■■ Connecting to the Ground via the Power Supply If the device is installed in the normal environment, the device can be grounded via the PE (Protecting Earth) cable of the AC power supply as shown in the following figure. FFFFFFFFFFF Connecting to the Ground Note: The figure is to illustrate the application and principle.
Gigabit Smart Switch Grounding Terminal Equipotential Bonding Cable Ground Cable Grounding Bar FFFFFFFFFFF Equipotential Bonding When equipotential bonding, please note that the cable should be copper wrapped 2 Kelly with its area being 6mm at least. The shorter cable the better, and use a grounding bar to establish an equipotential bonding point. Note: The equipotential bonding cable and ground cable are not provided with our product. If needed, please self purchase it.
Gigabit Smart Switch ■■ ■■ The port rate of the signal lightning arrester should match the rate of the desired port on the device. If it is not matched, this signal lighting arrester will not work. Purchase a standard lightning arrester. Install signal lightning arrester near the protected device and connect it to the ground via a shorter ground cable.
Gigabit Smart Switch CCCCCCCCCC Connection 4444 Ethernet Port Connect a Ethernet port of the Switch to the computer by RJ45 cable as the following figure shown. RJ45 Port RJ45 Cable FFFFFFFFFFFFConnecting the RJ45 Port 4444 SFP Port Connect the SFP port to a SFP module. If an SFP transceiver (purchased separately) is installed in a slot and has a valid link on the port, the associated RJ45 port will be disabled and cannot be used.
Gigabit Smart Switch 4444 Verify Installation After completing the installation, please verify the following items: ■■ There are 5~10cm of clearance around the sides of the device for ventilation and the air flow is adequate. ■■ The voltage of the power supply meets the requirement of the input voltage of the device. ■■ The power socket, device and rack are well grounded. ■■ The device is correctly connected to other network devices.
Gigabit Smart Switch CCCCCCCCCC Configuration 5555 Configure the Switch via GUI 111To access the GUI of the Switch, open a web browser and type the default management address http://192.168.0.1 in the address field of the browser, then press the Enter key. FFFFFFFFFFFFWeb Browser Note: To log on to the GUI of the Switch, the IP address of your PC should be set in the same subnet addresses of the Switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is 255.255.255.0.
Gigabit Smart Switch FFFFFFFFFFFFMain Page of the Switch 5555 Configure the Switch Using CLI You can log on to the Switch and access the CLI by Logging on to the Switch remotely by a Telnet connection through an Ethernet port. To log on to the switch by a Telnet connection, please take the following steps: 111Make sure the switch and the PC are in the same LAN. 222Click Start→Run to open the Run window.
Gigabit Smart Switch 333Type cmd in the prompt Run window as Figure 5-5 and click OK. FFFFFFFFFFFFRun Window 444Type telnet 192.168.0.1 in the command prompt shown as Figure 5-6, and press the Enter button. FFFFFFFFFFFFConnecting to the Switch Note: TL-SG2452 is unaccessible through Telnet Connection so that no configuration can be made by using CLI.
Gigabit Smart Switch Appendix A Troubleshooting QQQQ What could I do if I forgot the username and password of the Switch? Press the Reset button for at least 5 seconds to reset the system. The system will be reset to the factory default settings, and the default login user name and password are both admin. QQQQ Why does the Power LED work abnormally? The Power LED should be lit up when the power system works normally.
Gigabit Smart Switch Appendix B Hardware Specifications Item Content IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX/100Base-FX Standards IEEE 802.3ab 1000Base-T IEEE 802.3z 1000Base-X IEEE 802.3x Flow Control IEEE 802.3af (for TL-SG2424P only1 IEEE 802.3at (for TL-SG2424P only1 10Base-T: UTP/STP of Cat. 3 or above (maximum 100m1 100Base-TX: 2-pair UTP/STP of Cat. 5 or above (maximum 100m1 Transmission Medium 100Base-FX: MMF or SMF SFP Module (Optional1 1000Base-T: 4-pair UTP/STP of Cat. 5, Cat.
Gigabit Smart Switch Appendix C Technical Support ■■ For more troubleshooting help, please go to: www.tp-link.com/support/faq ■■ To download the latest Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/en/support/download ■■ For all other technical support, please contact us by using the following details: Global Singapore UK USA/Canada Tel: +86 755 2650 4400 E-mail: support@tp-link.com Service time: 24hrs, 7 days a week Tel: +65 6284 0493 E-mail: support.sg@tp-link.
Gigabit Smart Switch Germany/Austria Tel: +49 1805 875 465 (German Service) +49 1805 TPLINK +43 820 820 360 E-mail: support.de@tp-link.com Fee: 0.14 EUR/min from the German fixed phone network and up to 0.42 EUR/min from mobile phone Service time: Monday to Friday, 09:00 to 12:30 and 13:30 to 17:30. GMT+ 1 or GMT+ 2 (Daylight Saving Time in Germany) Switzerland Russian Federation Ukraine Brazil Poland *Except bank holidays in Hesse Tel: +41 (0) 848 800 998 (German Service) E-mail: support.ch@tp-link.
Website: http://www.tp-link.com E-mail: support@tp-link.com 7106504146 Rev: 1.1.
