User Guide TL-SF1008P 8-Port 10/100Mbps Desktop PoE Switch Rev：1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2008 TP-LINK TECHNO- LOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
CONTENT Package Contents ......................................................1 Chapter 1. Introduction of the Product 1.1 1.2 1.3 Chapter 2. Installation 2.1 2.2 ..........................1 Overview of the Product ...................................... 1 Convention ............................................................ 2 Features................................................................. 2 ................................................3 Mounting the Switch on a Desk.....................
Package Contents The following items should be found in your box: ¾ One TL-SF1008P 8-Port 10/100Mbps Desktop PoE Switch ¾ One DC Power Adapter ¾ Four rubber cushions to be used under the switch ¾ This User Guide Note Make sure that the box contains the above items. If any of the listed items are damaged or missing, please contact with your distributor. Chapter 1. Introduction of the Product Thank you for choosing the TL-SF1008P 8-Port 10/100Mbps Desktop PoE Switch. 1.
*PSE: a device (switch or hub for instance) that will provide power in a PoE setup. *PoE: This technology describes a system to transmit electrical power, along with data, to remote devices over standard twisted-pair cable in an Ethernet network. *PD: a device powered by a PSE and thus consumes energy. Examples include powering IP telephones, wireless LAN access points, network cameras, network hubs, embedded computers etc. 1.
¾ LED indicators for monitoring power, link, activity and speed ¾ External power adapter supply Chapter 2. Installation During the installation procedure, please only use the accessories equipped with the switch. 2.1 Mounting the Switch on a Desk To install the Switch, please follow the steps: 1) You can place the Switch on a flat desk. 2) Please insert the power adapter carefully to the power socket of the switch, and then connect it properly to a power source through the cable of the switch.
2.2 Power On The TL-SF1008P Switch can be used with DC power supply. Powering on the Switch, it will automatically initialize and its LED indicators will respond as follows: 1) All the LED indicators except PoE ports LED will light synchronously at first, then all of them included Link/Act LED (green), 100Mbps LED (green) and PoE MAX LED (red), will light off at once, which indicates the system initialized well. 2) The Power indicator will light all the time.
Name Power Status On(green) Off On(green) PoE ports On(red) (port-1~port-4) Off Flashing (red) PoE MAX On(red) Off Flashing (green) Link/Act On(green) (port-1~port-8) Off Indication Power on. Power off. There is a PoE PD connected to the port, which supply power successfully. The PoE power circuit may be in short, or the power current may be over that of the PD’s classification. No PD connected to the corresponding port，or no power is supplied according to the power limits of the port.
On(green) 100Mbps (port-1~port-8) Off There is a 100Mbps device connected to the corresponding port. There is a 10Mbps device connected to the corresponding port, or there is no device connected to the corresponding port. Note If all PoE PDs power consumption is >= 53w, a priority* will be arranged among the PoE ports like port-1 > port-2 > port-3 > port-4, then the system will cut off the power of the lowest-priority port.
The following parts are located on the rear panel: ¾ Power (48V): 48V indicates the input voltage of the power adapter provided with this TL-SF1008P Switch. The Power socket is where you will connect the power adapter. ¾ PoE Ports (1-4): These ports support PoE function which integrates power and data onto one the same cable.
Appendix A: Specifications General Standard Topology Protocol Data Transfer Rate Network Media(Cable) Number of Ports PoE Power on RJ-45 LEDs Transfer Method MAC Address Learning Frame Filter Rate Frame Forward Rate IEEE802.3,IEEE802.3u,IEEE802.3x,IEEE802.
Environmental and Physical 5.8 watts. (max. no PD connected) Power Consumption 58 watts (max.
