TD-8610/TD-8610B External ADSL2+ MODEM Rev: 1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2008 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Package Contents The following contents should be found in your package: ¾ One TD-8610/TD-8610B External ADSL2+ MODEM ¾ One AC power Adapter for TD-8610/TD-8610B External ADSL2+ MODEM ¾ One RJ45 cable ¾ Two RJ11 cable ¾ One ADSL splitter (only available for TD-8610) ¾ One Resource CD for TD-8610/TD-8610B External ADSL2+ MODEM, including: • This User Guide • Other Helpful Information ) Note: Make sure that the package contains the above items.
CONTENTS Chapter 1. Product Overview ....................................................................1 1.1 Product main specification .............................................................................1 1.2 Supporting protocol ........................................................................................1 1.3 Transmit data-rate ..........................................................................................1 1.4 ATM property.........................................
TD-8610/8610B External ADSL MODEM Chapter 1. Product Overview With the excellent design of circuit and high quality production, we guarantee ADSL2+ MODEM a high performance, very good stability and easy to use. TD-8610/TD-8610B is a complete plug-and-play solution. With standard Ethernet interface, it can be directly connected to any 10M/100M Ethernet devices, support Auto-MDIX.
TD-8610/8610B ¾ Max upload data-rate: 1Mbps ¾ Max line length: 6Km External ADSL MODEM 1.4 ATM property ¾ AAL0, AAL5, OAM, RM, and raw cell types supported ¾ Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs supported in software ¾ Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) 1.5 System support ¾ Support PVC ¾ Support IEEE 802.3、IEEE 802.3u ¾ Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet ¾ Support Auto-MDIX 1.
TD-8610/8610B External ADSL MODEM Chapter 2. Hardware Installation Guide 2.1 System requirement Confirm your computer has been installed with networking interface card (NIC) before connecting ADSL MODEM to your computer, with operating system supporting the TCP/IP protocol. 2.
TD-8610/8610B External ADSL MODEM 2.3 Rear-panel ¾ ON/OFF: Turn on/off the ADSL modem’s power. ¾ Power (9VAC/0.8A input): please do not use any unknown power adaptor, otherwise that may cause damage to your ADSL MODEM. ¾ RESET (reset default): When the device is working, please press the reset button of the Modem, keep the reset button pressed down for more than five seconds and then wait for the router to reboot. ¾ LAN: Connect with your computer’s NIC.
TD-8610/8610B Figure 2-1 5 External ADSL MODEM
TD-8610/8610B External ADSL MODEM Chapter 3. How to use 3.1 Computer Configuration 1. Connect the cable according to Chapter 2, and then turn on the power. 2. Change the IP address of your PC(Figure 3-1): Open TCP/IP Properties of the LAN card in your PC, enter the IP address as 192.168.1.* (* is any value between 2 to 254, Subnet mask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided by ISP).
TD-8610/8610B External ADSL MODEM Choose Properties -> Right-click Local Connection -> Choose Properties -> Double-press Internet Protocol (TCP/IP). 3) The words in fact maybe are different with this guide. You can check whether your configuration is successful through PING command. Enter Ping 192.168.1.1 If the screen likes the following, your configuration is successful. Figure 3-2 If the screen likes the following, your configuration is unsuccessful. Please repeat the previous steps again.
TD-8610/8610B External ADSL MODEM Figure 3-4 The default user name and its password is admin; if you want to change it, please go to "Management→Password". (Figure 3-5) Figure 3-5 3.3 Setup 1) Choose ATM PVCs Configuration (See Figure 3-6) 2) Enter the VPI/VCI value which is provided by your ISP, click Save to finish the configuration. You can press Next to add VPI/VCI value.
TD-8610/8610B External ADSL MODEM Figure 3-6 3.4 Software Dial TD-8610/TD-8610B works in bridged (RFC 1483 Bridged) mode to connect to the Internet. You need to install dial software on your PC. There is some software working on WINDOWS in market, example for EnterNet3000, RASPPPoE and WinPeET.
TD-8610/8610B Appendix A: Default Configuration USER NAME admin PASSWORD admin IP ADDRESS 192.168.1.