TD-8616 ADSL2+ Modem Rev: 1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations.
DECLARATION OF CONFORMITY For the following equipment: Product Description: ADSL2+ Modem Model No.
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Introduction ........................................................................................ 2 1.1 Product Overview .................................................................................................... 2 1.2 Main Features ......................................................................................................... 2 1.
TD-8616 ADSL2+ Modem User Guide Package Contents The following items should be found in your package: One TD-8616 ADSL2+ Modem One Power Adapter for TD-8616 ADSL2+ Modem Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter One Resource CD , including: This User Guide Other Helpful Information Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.
TD-8616 ADSL2+ Modem User Guide Chapter 1. Introduction Thank you for choosing the TD-8616 ADSL2+ Modem . 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet network. The Modem is easy to use. Connect the TD-8616 to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors.
TD-8616 ADSL2+ Modem User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel, which indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Power LAN ADSL Internet Status Indication On The modem is powered on. Off The modem is off. Please ensure that the power adapter is connected correctly. On There is a device connected to this LAN port.
TD-8616 2.2 ADSL2+ Modem User Guide The Back Panel Figure 2-2 ON/OFF: The switch for the power. POWER: The Power plug is where you will connect the power adapter. RESET: There are two ways to reset the Modem's factory defaults. Method one: With the Modem powered on, use a pin to press and hold the RESET button (about 5 seconds) until all LEDs are lit. And then release the button and wait for the Modem to reboot to its factory default settings.
TD-8616 ADSL2+ Modem User Guide Figure 2-3 Wall-mount Install Note: The diameter of the screw, 4mm
TD-8616 ADSL2+ Modem User Guide TD-8616. Connect the other end to the MODEM port of the external splitter. Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s Ethernet port or a regular hub/switch port, and the other end to the LAN port on the TD-8616. Step 3: Attach the power adapter. Connect the power adapter to the POWER connector on the rear of the device and plug in the adapter to a wall outlet or power extension.
TD-8616 ADSL2+ Modem User Guide Chapter 3. Quick Installation Guide 3.1 Configuring the PC After you directly connect your PC to the TD-8616 or connect your adapter to a Hub/Switch which has connected to the Modem, you need to configure your PC’s IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1).
TD-8616 ADSL2+ Modem User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button.
TD-8616 ADSL2+ Modem User Guide Figure 3-3 Step 4: Configure the IP address (Figure 3-4): Enter the IP address as 192.168.1.* (* is any value between 2 to 254, Subnet mask is 255.255.255.0). After that, click OK.
TD-8616 ADSL2+ Modem User Guide Figure 3-4 Note: 1) The users of Windows 98 can open TCP/IP Properties according to the following: Right-press (Mouse) Network Neighbor -> Choose Properties -> Double-press TCP/IP. PCI Fast Ethernet Adapter. 2) The words in fact maybe are different with this guide. Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd in the field and press Enter.
TD-8616 ADSL2+ Modem User Guide Figure 3-5 If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Modem. Figure 3-6 You can check it following the steps below: 1) Is the connection between your PC and the Modem correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Modem's IP address is 192.168.1.
TD-8616 ADSL2+ Modem User Guide Figure 3-7 After that you will see the page as follow when ADSL connection is OK.
TD-8616 ADSL2+ Modem User Guide Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Management page. After your successful login, you can configure and manage the device.
TD-8616 ADSL2+ Modem User Guide Figure 4-2 4.1.2 Traffic Statistics Choose “Statistics→Traffic Statistics” menu, and you will be able to view the traffic statistics about the Modem.
TD-8616 4.2 ADSL2+ Modem User Guide Basic Setup Choose “Basic Setup”, you can see the next submenus: WAN Setting, LAN Setting and ADSL. Click any of them, and you will be able to configure the corresponding function. Figure 4-4 4.2.1 WAN Setting Choose “Basic Setup→WAN Setting” menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-5). Figure 4-5 WAN Setting: WAN settings are used to connect to your ISP.
TD-8616 ADSL2+ Modem User Guide Figure 4-6 • PVC Pool: PVC Pool contains multiple VPI/VCI sets. The Modem can match PVC automatically and it can plug and play. The detailed VPI/VCI sets inside PVC Pool are shown in Figure 4-7, besides you can add VPI/VCI sets to or remove VPI/VCI sets from the PVC pool. Figure 4-7 • Status: If you want to use a designed VC, you should activate it. • VPI: Identify the virtual path between endpoints in an ATM network. The valid range is from 0 to 255.
TD-8616 ADSL2+ Modem User Guide Figure 4-8 PVC Poll: • PVC Poll: PVC Pool is activated as default. If unnecessary, please do not modify the status of PVC Pool. 4.2.2 LAN Setting Choose “Basic Setup→LAN Setting” menu, and you will see the LAN screen (shown in Figure 4-9). Please configure the parameters for LAN ports according to the descriptions below. Figure 4-9 LAN Setting: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings.
TD-8616 ADSL2+ Modem User Guide 4.2.3 ADSL Choose “Basic Setup→ADSL”, you can select the ADSL Mode and the Annex Type in the next screen. You can change the ADSL features when meeting physical connection problem. Please check the proper settings with your ISP. Figure 4-10 ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. Annex Type: Select the Annex type which your ADSL connection uses. 4.
TD-8616 ADSL2+ Modem User Guide Figure 4-12 Note: 1) 2) There is only one account that can access the Web-based Management page. The default account is "admin", and the password is "admin". Admin has read/write access privilege. When you change the password, you should enter the new password twice, and then click Save to make the new password take effect. 4.3.2 Firmware Upgrade Choose “Maintenance→Firmware Upgrade”, you can upgrade the firmware of the Modem in the screen (shown in Figure 4-13).
TD-8616 ADSL2+ Modem User Guide Note: 1) 2) 3) 4) New firmware versions are posted at www.tp-link.com and can be downloaded for free. If the modem is not experiencing difficulties, there is no need to download a more recent firmware version, unless the version has a new feature that you want to use. When you upgrade the modem's firmware, you may lose its current configurations, so please back up the modem’s current settings before you upgrade its firmware.
TD-8616 ADSL2+ Modem User Guide Appendix A: Specifications General Standards and Protocols Safety & Emission Ports LEDs ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, G.992.4, ITU G.992.5, IEEE 802.3, IEEE 802.3u, TCP/IP, HTTP FCC, CE 1 10/100M Auto-Negotiation RJ45 port（Auto MDI/MDIX) 1 RJ11 port Power, LAN, ADSL, Internet 10Base-T: UTP category 3, 4, 5 cable Network Medium 100Base-TX: UTP category-5 Max line length: 6.
TD-8616 ADSL2+ Modem User Guide Appendix B: Troubleshooting T1. How can I restore my Modem’s configuration to its factory default settings? With the Modem powered on, use a pin to press and hold the RESET button on the rear panel for 5 seconds before releasing it. Hold it for 5 seconds Note Once the Modem is reset, the current configuration settings will be lost and you will need to re-configure all the parameters. T2.
TD-8616 ADSL2+ Modem User Guide Appendix C: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details: Global Tel: +86 755 2650 4400 Fee: Depending on rate of different carriers, IDD. E-mail: support@tp-link.
