TD-8841 External ADSL Router Rev: 1.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2008 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Product Overview............................................................................... 2 1.1 Product Main Specification........................................................................................ 2 1.2 Supporting Protocol................................................................................................... 2 1.
TD-8841 External ADSL2+ Router User Guide Package Contents The following items should be found in your package: ¾ One TD-8841 External ADSL2+ Router ¾ One AC power Adapter for TD-8841 External ADSL2+ Router ¾ One Resource CD for TD-8841 External ADSL2+ Router, including: z This Guide z Quick installation Guide Program z Other Helpful Information z USB driver ¾ Quick installation Guide ¾ One RJ45 cable ¾ Two RJ11 cables ¾ One ADSL splitter ¾ One USB cable ) Note: Make sure that the package
TD-8841 External ADSL2+ Router User Guide Chapter 1. Product Overview With the excellent circuit design and high quality production, we guarantee the ADSL2+ Router’s high performance, great stability and easy to use. In addition to the basic DMT physical layer functions, the ADSL2+ PHY supports dual latency ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer. The TD-8841 is a complete plug-and-play solution.
TD-8841 ¾ Supports RFC1483 (EoA)(Bridged *and Router) ¾ Supports RFC1577 (IPoA) External ADSL2+ Router User Guide ) Note: “*” Needs the third-party software. 1.3 Transmit Data-rate ¾ Max download data-rate: 24Mbps ¾ Max upload data-rate: 3.5Mbps ¾ Max line length: 6Km 1.
TD-8841 External ADSL2+ Router User Guide Chapter 2. Hardware Installation Guide The TD-8841 maintains six separate interfaces, including four Ethernet interfaces, one USB interface and one ADSL interface. The Router should not be located where it will be exposed to moisture or excessive heat. Place the Router in a location where it can be safely connected to the various devices as well as to a power source. 2.
TD-8841 ¾ External ADSL2+ Router User Guide Power (9V AC/0.8A input): please do not use any unknown power adaptor; otherwise your ADSL2+ Router may be damaged. ¾ RESET (reset default): First press the reset button of Router, then turn on the Router’s power for at least three seconds. It will resume the default manufacturer’s setup. ¾ LAN: Connect with your computer’s NIC.
TD-8841 External ADSL2+ Router User Guide Chapter 3. System Configuration 3.1 Computer Configuration The default IP address of the ADSL2+ Router is 192.168.1.1, and the default Subnet Mask is 255.255.255.0. These values can be seen from the LAN, and can be changed as your desire. As an example, we use the default values for description in this guide. 1. Connect the cable according to Chapter 2, turn on the power. 2. Connect the local PCs to the ADSL2+ Router’s LAN port.
TD-8841 External ADSL2+ Router User Guide 3.2 Login Startup Internet Explorer, and enter 192.168.1.1;then enter default user name (admin)、password (admin), When ADSL2+ connection is OK, you will see the Figure 3-1. Figure 3-1 You will then see the Figure 3-2. You will see some information such as link rate and so on.
TD-8841 External ADSL2+ Router User Guide Figure 3-2 Default value of user name and password is “admin”; if you want to change them, please go to “Management” Æ “Access control”Æ“Passwords” changing them. (Figure 3-3) Figure 3-3 3.3 Web Setup Choose “Advanced Setup”Æ”WAN”, you will enter the page of Wide Area Network (WAN) Setup, you will see the Figure 3-4.
TD-8841 External ADSL2+ Router User Guide Figure 3-4 There are 7 PVC links in the WAN setup page, choose the fit PVC according to your needs, and then click the edit button, you will enter the page of ATM PVC Configuration (See Figure 3-5). Figure 3-5 Enter VPI/VCI value and service category which is provided by your ISP, click next to enter the next step. You will see the Figure 3-6.
TD-8841 External ADSL2+ Router User Guide ) Note: The type of network protocol selected may be different in different areas, there are five types （Figure 3-7）, So you should ask your ISP to acquire the local type of network protocol and Encapsulation mode. Figure 3-6 After choosing the proper protocol, enter the correct parameters supported by your ISP. Enable the configurations，then you will go to Internet.
TD-8841 External ADSL2+ Router User Guide Figure 3-7 You will see the Figure 3-8. Then turn on the selected functions according to your demands. Clicking the next button to enter the next step, you will see the Figure 3-9, finally click save to complete the configuration.
TD-8841 External ADSL2+ Router User Guide Figure 3-9 ¾ PPP over Ethernet (PPPoE) If you select the protocol of PPP over Ethernet (PPPoE), you will see the Figure 3-10, enter the value of user name and password which is provided by your ISP, after selecting the other function (often using the default setup), click the next button. Figure 3-10 You will see the Figure 3-11. Then turn on the selected functions according to your needs.
TD-8841 External ADSL2+ Router User Guide Figure 3-11 Figure 3-12 ¾ MAC Encapsulation Routing (MER) If you select the protocol of MAC Encapsulation Routing (MER), you will see the page (Figure 3-13) Enter the parameter and the way which is provided by your ISP, then click the next button.
TD-8841 External ADSL2+ Router User Guide Figure 3-13 You will see the Figure 3-14. Then turn on the selected functions according to your needs. Clicking the next button to enter the next step, you will see the Figure 3-15, finally click save to complete the configuration.
TD-8841 External ADSL2+ Router User Guide Figure 3-15 ¾ IP over ATM (IPoA) If you select the protocol of IP over ATM (IPoA), you will see the Figure 3-16, enter the parameter and the way which is provided by your ISP, then click the next button. Figure 3-16 You will see the page (Figure 3-17), then turn on the selected functions according to your needs. Clicking the next button to enter the next step, you will see the Figure 3-18, finally click save to complete the configuration.
TD-8841 External ADSL2+ Router User Guide Figure 3-17 Figure 3-18 ¾ Bridging If you select the Bridging protocol, you just open the bridge service function options, you will see the Figure 3-19, then click the next button, you will see the Figure 3-20, finally press save to complete the configuration.
TD-8841 External ADSL2+ Router User Guide Figure 3-19 Figure 3-20 ) Note: After you complete the settings, the new settings must be saved and the Router must be restarted for the settings to go into effect. Please press the Save/Reboot button to restart, referring to the Figure 3-21.
TD-8841 External ADSL2+ Router User Guide Figure 3-21 3.4 Software Dial If TD-8841 CPE work in bridged (RFC 1483 Bridged) mode when it connects Internet. You must to install dial software on your PC. There are some software working on WINDOWS in market, example for EnterNet3000、RASPPPoE、WinPeET. How do I set up the connection in the windows XP? ¾ Users of Windows XP can click the “start->All Programs->Accessories-> Communications->New connection wizard”, then click Next to enter the setting page.
TD-8841 ¾ External ADSL2+ Router User Guide Users of Windows Vista can do as following: Right-press Network->Choose Properties, then you can see Figure 3-22. Figure 3-22 ¾ Click “Set up a connection or network” in the right of this page. And choose “Set up a dial-up connection” in the new page, click Next. After that, you will see Figure 3-23, click “Set up a connection anyway” to enter next page.
TD-8841 ¾ External ADSL2+ Router User Guide Type the Dial-up phone number, the User name and password supplied by your ISP in the new page, if you have forgotten an existing user name or password, please connect with your ISP. Click Create to create the dial-up connection. ¾ Click Close to finish the setup. ¾ To connect to the Internet next time, click the Start button, click Connect to, and then click the connection you just created. 3.
TD-8841 External ADSL2+ Router User Guide Figure 3-25 Select the ‘search removable media(floppy, CD-ROM…)’, and click the next button. You will see the Figure 3-26. The driver will be search and installed. ) Note: You must insert the CD first.
TD-8841 External ADSL2+ Router User Guide Waiting and you will see the Figure 3-27. When the driver finished installation, click Finish to close the installation. Please refer to chapter 3.1 to finish the IP configuration of USB network connection. Then you could use the USB device. Figure 3-27 Users of Windows Vista will see the Figure 3-28. Click the “Locate and install driver software (recommended)” to install driver software for your USB Network Interface.
TD-8841 External ADSL2+ Router User Guide Figure 3-28 After that you will enter the next page shown as Figure 3-29. Click “Don’t search online”. Figure 3-29 Then Figure 3-30 will be displayed. Click Next to search and install the driver from your CD. ) Note: You must insert the CD first.
TD-8841 External ADSL2+ Router User Guide Figure 3-30 When Windows find the driver automatically, it will pop up Figure 3-31. Select “Install this driver anyway” to continue the installation. Figure 3-31 Then please wait a second and you will see Figure 3-32 which indicates that the installation has been finished. Finally, click Close to finish it completely.
TD-8841 External ADSL2+ Router User Guide Figure 3-32 You can see following figure at the bottom of the screen. Figure 3-33 ) Note: If you want cut off the USB device you must disconnect the network of USB first.
TD-8841 External ADSL2+ Router User Guide Chapter 4. Advantage Management Setup In order to satisfy our customer's needs we offer an excellent Web management interface. Feel free to utilize the Advantage application and online software upgrades. The functions of the Web management interface are as follows: ¾ Upgrade software ¾ Modify the default IP address of the port of LAN (192.168.1.
TD-8841 External ADSL2+ Router User Guide Chapter 5. FQA 1. What related parameters are required to acquire ISP when you want to access the internet by ADSL2+ Router? 1) Dial user: Connection protocol, User name, Password, Value of VPI/VCI, Encapsulation mode of AAL5 and so on. 2) Static IP user: Connection protocol, WAN IP Address, Subnet Mask, Gateway, Value of VPI/VCI, Encapsulation mode of AAL5 and so on. 2. 3. 4.
TD-8841 External ADSL2+ Router User Guide Appendix A: Default Configuration USER NAME admin PASSWORD admin IP ADDRESS 192.168.1.
TD-8841 External ADSL2+ Router User Guide Appendix B: Configuring the PCs In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows 2000/XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed. 1. Install TCP/IP component 1) Right-press Network Neighbor and Choose Properties. 2) Right click the icon that showed below, select Properties on the prompt page.
TD-8841 External ADSL2+ Router User Guide Figure B-2 4) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
TD-8841 External ADSL2+ Router User Guide Figure B-3 ¾ Setting IP address manually 1 Select Use the following IP address radio button. And the following items available 2 If the router's LAN IP address is 192.168.1.1, type IP address is 192.168.1.x (x is from 2 to 254), and Subnet mask is 255.255.255.0. 3 Type the router’s LAN IP address (the default IP is 192.168.1.1) into the Default gateway field. 4 Select Use the following DNS server addresses radio button.
TD-8841 External ADSL2+ Router User Guide Figure B-4 Please note: The configuration under Windows 98/Vista is a little different from that of Windows 2000/XP. Users of Windows 98 can open TCP/IP Properties according to the following: Right-click (Mouse) Network Neighbor -> Choose Properties -> Double-click TCP/IP PCI Fast Ethernet Adapter. Users of Windows Vista can do following: Right-press Network->Choose Properties, then you can see Figure B-5.
