User Guide TL-POE150S PoE Injector Rev:3.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
CONTENTS Package Contents.................................................................... 1 Chapter 1 Introduction .......................................................... 1 1.1 1.2 Overview of the Product .............................................. 1 Features ...................................................................... 2 Chapter 2 Identifying External Components....................... 2 Chapter 3 Connecting the PoE Injector............................... 3 Appendix: Specifications.....
Package Contents The following items should be found in your package. ¾ ¾ ¾ ¾ TL-POE150S PoE Injector One Power Adapter One Ethernet (CAT5 UTP) Cable This User Guide ) Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor. Chapter 1 Introduction 1.1 Overview of the Product Thank you for choosing the TL-POE150S PoE Injector.
*PoE: This technology describes a system to transmit electrical power, along with data, to remote devices over standard twisted-pair cable in an Ethernet network. *PD: A device powered by a PSE and thus consumes energy. Examples include powering IP telephones, wireless LAN access points, network cameras, network hubs, embedded computers etc. *PSE: A device (switch or hub for instance) that will provide power in a PoE setup. 1.2 Features ¾ Complies with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.
DC 48V: Connect to the provided power adapter which can supply steady power of 48V DC. LAN IN: Connect to a network device (such as a Switch or Router ) with CAT5 UTP cable. PWR: Power LED. A steady blend color of red and yellow indicates that the power adapter is working properly. A steady green light indicates that the PoE system has detected the PD or PoE Splitter and the PoE Injector is supplying power normally. A flashing light indicates abnormal power supply.
There are two schemes to realize the PoE. 1. If the device supports PoE (take an IP camera with PoE for example), following topology will work: Scheme 1 2. If the device does not support PoE, it is necessary to have a PoE Splitter to separate the power and data, transmitting them detached in one UTP cable and one power cable. Here we take TP-LINK TL-POE10R Splitter for example. You can use following topology.
) Note: ¾ Do not mistake the power port of the TL-POE150S and TL-POE10R when choosing the Scheme 2, or else it will cause serious damage to your network device. ¾ If you want to know more details about TL-POE10R Splitter, please refer to “TL-POE10R User Guide” on our website http://www.tp-link.com. Appendix: Specifications Normal Standards Ports Cabling Type LED Safety & Emissions IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.
