Installation Guide TL-SF1008P 8-Port 10/100Mbps Desktop Switch with 4-Port PoE REV4.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
CONTENT Package Contents ...................................................... 1 Chapter 1. Introduction of the Product 1.1 1.2 1.3 .......................... 2 Overview of the Product ...................................... 2 Convention ............................................................ 3 Features................................................................. 3 Chapter 2. Installation................................................. 4 2.1 2.2 Mounting the Switch on a Desk...................
Package Contents The following items should be found in your box: ¾ One TL-SF1008P 8-Port 10/100Mbps Desktop Switch with 4-Port PoE ¾ One DC Power Adapter ¾ Four rubber cushions to be used under the switch ¾ This Installation Guide Note Make sure that the box contains the above items. If any of the listed items are damaged or missing, please contact your distributor.
Chapter 1. Introduction of the Product Thank you for choosing the TL-SF1008P 8-Port 10/100Mbps Desktop Switch with 4-Port PoE. 1.1 Overview of the Product The TL-SF1008P 8-Port 10/100Mbps Desktop Switch with 4-Port PoE provides the seamless network connection, which integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities. This PoE switch is also a Power Sourcing Equipment (PSE*).
1.2 Convention The switch or TL-SF1008P mentioned in this Installation Guide stands for TL-SF1008P 8-Port 10/100Mbps Desktop Switch with 4-Port PoE without any explanation. 1.3 Features ¾ Complies with IEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.3af standards ¾ 8 10/100Mbps Auto-Negotiation RJ45 ports with 4 ports supporting PoE function (port-1~port-4), all of them support Auto-MDI/MDIX ¾ Supports PoE power up to 15.
Chapter 2. Installation During the installation procedure, please only use the accessories equipped with the switch. 2.1 Mounting the Switch on a Desk To install the switch, please follow the steps: 1) Place the switch on a flat desk. 2) Remove the adhesive backing papers from the rubber cushions. 3) Turnover the switch and attach the supplied four rubber cushions to the recessed areas on the bottom at each corner of the switch. Note 1) Please avoid any heavy thing placed on the switch.
2.2 Power On The TL-SF1008P switch can be used with DC power supply. Powering on the switch, it will automatically initialize and its LED indicators will respond as follows: 1) Firstly, the Power LED indicator will light up. 2) Then, the Link/Act LED indicators will flash momentarily for one second, which represents a resetting of the system. Note If the LED indicators don’t respond as described above, please check the power supply and its connection. Chapter 3.
Name Status Indication Power On (green) The switch is powered on. PoE ports (port-1~ port-4) Off On (green) Flashing (green) Off On (red) The switch is powered off. There is a PoE PD connected to the port, which supplies power successfully. The PoE power circuit may be in short or the power current may be overloaded. No PD is connected to the corresponding port，or no power is supplied according to the power limits of the port. The power of all the connected PoE ports is >=50W.
port-4, then the system will cut off the power of the lowest-priority port. *Priority: This function will help protect the system when the system power is overloaded. For example, Port 1, 2 and 4 is using 15.4W (maximum power for per port is 15.4W); the system power is 46.2W in total. If there is an additional PD inserted to Port 3 with 12W, and then the system will cut off the power of Port 4 because of the overloaded power, this means Port 1, 2 will use 15.
¾ Ethernet Ports (1-8): Besides the 4 PoE ports, the TL-SF1008P switch is also equipped with the other four 10/100Mbps Auto-Negotiation RJ45 ports without PoE function. Once the network devices are connected to these 8 ports through the network cable, the switch will make them plug and play according to the Auto-MDI/MDIX detection. The working status can be indicated by the corresponding LEDs on the front panel. Note Make sure the PDs you connected to the switch are complaint with IEEE 802.3af.
Appendix A: Specifications General Standard Protocol Data Transfer Rate Network Media(Cable) Number of Ports PoE Power on RJ45 LEDs Transfer Method MAC Address Learning Frame Filter Rate Frame Forward Rate IEEE802.3,IEEE802.3u,IEEE802.3x,IEEE802.
Environmental and Physical 2.3 Watts. (max. no PD connected) Power Consumption 59.3 Watts (max.
