User Guide TL-SL1210 8-Port 10/100Mbps + 2-Port Gigabit Switch TL-SL1117 16-Port 10/100Mbps + 1-Port Gigabit Switch TL-SL1226 24-Port 10/100Mbps + 2-Port Gigabit Switch TL-SL1351 48-Port 10/100Mbps + 3-Port Gigabit Switch Rev: 2.0.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2010 TP-LINK TECHNOLOGIES CO., LTD.
EC DECLARATION OF CONFORMITY (EUROPE) In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/ EEC, this product meets the requirements of the following standards: ¾ EN55022 ¾ EN55024 ¾ EN60950 CE MARK WARNING This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
CONTENTS Package Contents:.............................................................................1 Chapter 1 Introduction of the Product .........................................1 1.1 Overview of the product .................................................................... 1 1.2 Features ............................................................................................ 2 Chapter 2 Installation.....................................................................2 2.
Package Contents The following items should be found in your box: ¾ One Switch ¾ One power cord ¾ This User's Guide ¾ Rubber footpads for Desk-mount ¾ Rack-mount kit for installing the switch in a 19-inch rack Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.
Uplink ports, and any port can be simply plugged into a server, a hub, a router or a switch, using the straight cable or crossover cable. Diagnostic LEDs which display link status and activity, allowing you to quickly detect and correct problems on the network. 1.2 Features ¾ Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.
2.2 Mounting the Switch in a Rack The dimension of TL-SL1210/TL-SL1117/TL-SL1226/TL-SL1351 is designed according to the standard 19'' rack- mountable steel case of Electronic Industries Association. Turn off all the equipment connected to the Switch before mounting it in the rack, then rivet the two “L” brackets onto each side of the Switch, fasten it with screws in the rack. Note: For TL-SL1210, the “L” brackets will differ in size.
2.3 Mounting the SFP Module (for TL-SL1351 Only) The front panel of the TL-SL1351 consists of a SFP module, which support The Hot Plug- And- Draw. Should fixed the SFP into SFP pluggable when use the SFP module. The switch could identify and configure the SFP module automatically. 2.4 Power on TL-SL1210/TL-SL1117/TL-SL1226/TL-SL1351 Gigabit Switch is powered by AC power supply.
¾ 1000M LED: The corresponding gigabit port LED indicator will light solid green when the gigabit port connected to a 1000Mbps device. It flashes green when data is being transmitted or received on the working connection. ¾ 100M LED: The corresponding 100M port LED indicator will light solid green when the 10/100M port connected to a 100Mbps device. It flashes green when data is being transmitted or received on the working connection.
Appendix A: Specifications General IEEE802.3 10Base-T IEEE802.3u 100Base-TX Standards IEEE802.3ab 1000Base-T IEEE802.3z 1000Base-X (for TL-SL1351 only) ANSI/IEEE Std 802.3 Nway IEEE802.
Uplink Ports Auto MDI/MDI-X cable detection, Each port can be used Uplink ports Transfer Method Store-and-Forward MAC Address Table 8k, Automatically learning, automatically Update 10Base-T: 14880pps/Port Frame Filter 100Base-TX: 148810pps/Port Rate 1000Base-T: 1488095pps/Port 1000Base-X: 1488095pps/Port (for TL-SL1351 only) 10Base-T: 14880pps/Port Frame Forward Rate 100Base-TX: 148810pps/Port 1000Base-T: 1488095pps/Port 1000Base-X: 1488095pps/Port (for TL-SL1351 only) Safety & Emissions FCC, CE E