User's Guide TL-SL3226P 24+2G Gigabit Managed Switch Rev 1.0 E-mail: export@tp-link.com.
Trademark, Copyright statement Table of contents is the registered trademark of Shenzhen TP-LINK Technologies Co., Ltd. All rights reserved, contents may be revised Checklist...............................................................................................1 without prior notice. No part of this publication may be reproduced in any Chapter 1 form or by any means or used to make any derivative such as translation, 1.1 Usage..................................................................
4.2 How to connect TELNET...........................................................12 4.3 How to connect Out-of-Band.....................................................13 4.4 The interface and operating way of TELNET/Out-of-Band........14 4.4.1 Configure System......................................................................17 4.4.2 Port Management......................................................................20 4.4.3 Network...............................................................
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide TL-SL3226P 24+2G Gigabit Managed Switch User's Guide Checklist 1.3 Overview of this User's Guide Open the box and carefully unpack the TL-SL3226P. You should have all the Chapter 1 About this User's Guide items on the following checklist: Chapter 2 Introduction. Describes the switch and its features Chapter 3 Installation.
TL-SL3226P 2.2 24+2G Gigabit Managed Switch User's Guide Features and Specification TL-SL3226P Support static priority and IEEE802.1p class of service with 2-level ! priority mode 2.2.1 Features ! Fully comply with IEEE802.3 standard ! Full and half-duplex for both 10Mbps and 100Mbps connections. ! Support IEEE802.
TL-SL3226P Chapter 3 24+2G Gigabit Managed Switch User's Guide 24+2G Gigabit Managed Switch User's Guide TL-SL3226P Installation 3.1 Installation Follow these steps to install the switch: ! The surface must support at least 5kg ! The power source must be within 1.
24+2G Gigabit Managed Switch User's Guide TL-SL3226P 3.2 TL-SL3226P 24+2G Gigabit Managed Switch User's Guide connection port with PC when Out-of-Band management. Connecting the Switch 3.2.1 Front Panel There are 2 extension module slots, 24 10/100Mbps ports, one console Power LED ! Located between the console port and 24 normal ports, the power LED will (RS232) port and LED indicators on the front panel of the TL-SL3226P. be always green when power on.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide TL-SL3226P supports the power cord. Plug-in the female connector of the provided power Model No. Standard 24+2G Gigabit Managed Switch User's Guide Interface Network Media cord into this socket, and the male side of the cord into a power outlet. Supported input voltage range from 110 to 260VAC at 50-60Hz.
TL-SL3226P ! 24+2G Gigabit Managed Switch User's Guide TL-SL3226P 24+2G Gigabit Managed Switch User's Guide The TL-SL3226P can start to work with the correct power supply. Out-of-Band Management manages the Switch locally through the console Please confirm whether the power supply is accordant to the port, without occupying the bandwidth. requirements of the TL-SL3226P. ! In order to avoid the risk of the power-attach, don't open the shelf of the TL-SL3226P when it works.
TL-SL3226P 4.3 24+2G Gigabit Managed Switch User's Guide How to connect Out-of-Band Out-of-Band Management needs a terminal or a HyperTerminal. First, connect the Switch's console port with the PC's console port by the console cord. Then, run HyperTerminal. Refer to the following figure to TL-SL3226P 24+2G Gigabit Managed Switch User's Guide HyperTerminal Private Edition. The configuration way is similar with that on Windows. 4.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide The management interface is the menu drive. After you log on, you will in the TL-SL3226P 24+2G Gigabit Managed Switch User's Guide table, static address table and filter address table. first menu as following: The Spanning Tree protocol includes the Switch configuration (Open/Close Spanning Tree, Network Bridge Priority) and port configuration. (Such as port priority, situation). IEEE802.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide TL-SL3226P 24+2G Gigabit Managed Switch User's Guide The assumpsit of normal control button in the operating interface is as following: = Direction Button: up, down, left, right moves cursor =Tab Button: move the cursor to the next stay place , = W, w Button: move the cursor up , = S, s Button: move the cursor down , = S, s Button: move the cursor left Figure 4-3 System Configuration , = D, d Button: move
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide TL-SL3226P 2) When downloading TFTP, TFTP server must have the files for updating. ! Switch Parameters 1) Assigned Managed Port: can be any port or all ports from P1 to P26. Only the workstation connecting to the Assigned Managed Port in the 3) You must guarantee the TFTP server in operating. 4) To break the download is not allowed during the TFTP download. Or else the Switch may be out of the way. Switch can manage the Switch.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide TL-SL3226P 24+2G Gigabit Managed Switch User's Guide the IEEE802.1X protocol of Port 2 has been configured to be Enable. Please 10FD: 10Mbps, Full-Duplex note Port Security, Trunk and IEEE802.1X protocol are mutually exclusive. 100HD: 100Mbps, Half-Duplex In other word, when you configure one of them, other two can't be configured.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide TL-SL3226P 24+2G Gigabit Managed Switch User's Guide 10HD: 10Mbps, Half-Duplex be a sniffer port. The Sniffer port should in a same VLAN with the mirrored 10FD: 10Mbps, Full-Duplex port. 100HD: 100Mbps, Half-Duplex 100FD: 100Mbps, Full-Duplex Direction-Centric Mode Sniffer 1000HD: 1000Mbps, Half-Duplex Sniffer Port: can choose any port from port 1 to port 26. but it can't included in 1000FD: 1000Mbps, Full-Duplex the mirrored port.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide TL-SL3226P 24+2G Gigabit Managed Switch User's Guide is too short however, many entries may be aged out too soon. This will result Priority: 0 - 65535 in a high percentage of received packets whose source addresses cannot Hello Time: 1 - 10 be found in the forwarding table, in which case the switch will broadcast the Maximum Age Timer: 6- 40 packet to all ports, egating many of the benefits of having a switch.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide Table. TL-SL3226P 2) ! Static MAC Address ! Filter MAC Address ! Force UNAUTH MAC Address ! Authorized MAC Address 2) No matter which port the MAC Address of the Force UNAUTH MAC 24+2G Gigabit Managed Switch User's Guide When you configure the MTU VLAN and effect it, all original VLAN and Trunk configuration will be cancelled. 4.4.7 Configure Trunk Table relates to, the Switch won't transfer its' packets.
TL-SL3226P 2) 24+2G Gigabit Managed Switch User's Guide When you configure a Trunk, the ports added to the Trunk will be deleted from all VLANs no matter whether you create a Trunk or add TL-SL3226P 24+2G Gigabit Managed Switch User's Guide Before getting start, you must finish some preparing steps. We choose IE 5.0 in Windows 2000 to be an example. the port to a Trunk. If you delete any port or delete the whole Trunk, the original port in the Trunk can't reset to any VLAN.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide TL-SL3226P 24+2G Gigabit Managed Switch User's Guide The Forth Step: Choose Enable in the Active Scripting or choose Reset to Medium, press Reset and press OK. Figure 5-2 Settings Please choose Automatically, then press OK. The Third step: Choose Security User-defined. Figure 5-4 Security Settings The Fifth step: Press the right button of the mouse, choose Propertiesin the menu existed. The following screen will exist.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide 24+2G Gigabit Managed Switch User's Guide TL-SL3226P Input the user's name and password (the default user's name and password are supervisor. Furthermore, the default user has managing right.) Press OK to the page of WEB management. Caution The default user's name and password are set in factory. You can revise and add user's names and passwords in the Security Configuration. You must have management right when you revising such configuration.
TL-SL3226P 24+2G Gigabit Managed Switch User's Guide 24+2G Gigabit Managed Switch User's Guide TL-SL3226P Cross Cable RJ-45 Connector pin assignment The Switch (normal port) connects to the switch/hub/other equipments Connector pin assignment Contact (normal port).
TL-SL3226P Ports Management 24+2G Gigabit Managed Switch User's Guide Direction-centric Mode Sniffer Flow-centric Mode Sniffer Port Description Port Statistics Port BandWidth Network Spanning Tree IP Address Parameters MAC Address table Max Age Static MAC Address Table Filter MAC Address Switch Configuration Port Configuration IEEE802.
