TL-WN951N 300Mbps Wireless N PCI Adapter REV: 1.1.
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d’interférences et (2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil. Industry Canada Statement: Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N PCI Adapter Model No.
CONTENTS Package Contents....................................................................................................... 1 Chapter 1 Product Overview ............................................................................................2 1.1 Introduction.......................................................................................................... 2 1.2 Features................................................................................................................ 2 1.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Package Contents Please verify that all the package contents below are available. One TL-WN951N 300Mbps Wireless N PCI Adapter Quick Installation Guide One Resource CD for TL-WN951N, including: • • • TP-LINK Wireless Configuration Utility (TWCU) and Drivers User Guide Other helpful information Make sure that the above items are contained in the package. If any of the above items is damaged or missing, please contact your distributor.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Chapter 1 Product Overview 1.1 Introduction The adapter is a 802.11n client device designed to deliver a high-speed and unrivaled wireless performance for your desktop. With a faster wireless connection, you can get a better Internet experience, such as downloading, gaming, video streaming. With the 802.11n technology, the TL-WN951N’s auto-sensing capability allows high packet transfer rate of up to 300Mbps for maximum throughput.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide 1.3 Hardware Overview LED status: Status Off Working Status The driver has not been installed; The adapter's radio has been disabled. Flashing Slowly The driver has been installed but no data is being transmitted or received. Flashing Quickly Data is being transmitted or received.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Chapter 2 Installation Please install the PCI adapter into your computer before installing the driver and utility software from the Resource CD. 2.1 Hardware Installation 1. Turn off your computer and unplug the power cord from the computer. 2. Open the case and locate an available PCI slot. Remove the metal slot cover on the back of the PC. Keep the screws. Turn to your computer manufacturer for instructions if needed. 3.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 2-2 Found New Hardware Wizard in Windows Vista 2.2 Software Installation The adapter’s Setup Wizard will guide you through the installation procedures for and Windows XP, Windows Vista, Windows 7, and Windows 8. The procedures in different systems are quite similar, therefore here takes the procedures in Windows 7 for example. 1.
TL-WN951N 2. 3. 300Mbps Wireless N PCI Adapter User Guide The InstallShield Wizard window will appear. Click Next to continue. Figure 2-4 Choose a setup type. It is recommended to select Install TP-LINK Wireless Configuration Utility and Driver. Selecting Install Driver Only can only install driver. Click Next to continue.
TL-WN951N 4. 300Mbps Wireless N PCI Adapter User Guide Click Change… to specify the destination location for the software or you can leave it default. Click Next in the screen below to continue. Figure 2-6 5. Click Install to continue the setup.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide 6. The utility and drivers will install. It may take 1~2 minutes. 7. Figure 2-8 After all the steps above, you will see the screen below. Click Finish to complete the setup. Figure 2-9 8. After installation, the utility configuration page will automatically pop up as shown in the will appear in your system tray. To connect to a network, following figure and the icon please refer to Chapter 3 Connect to a Wireless Network.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 2-10 9
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Chapter 3 Connect to a Wireless Network With both the hardware and software successfully installed into your computer, you can quickly connect to a wireless network using one of the following methods. Method One: To connect using TWCU TL-WN951N uses the TP-LINK Wireless Configuration Utility as the management software. The utility provides you an easy interface to connect to a network and to change any settings related to the wireless adapter.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 3-2 3. You will be prompted different windows when you choose wireless network of different security types. 1) Wireless network of WPA/WPA2-Personal If you selected a wireless network of the security type WPA/WPA2-Personal, you will be prompted to enter the password in the security key field, as shown in Figure 3-3.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Certificate as your authentication, you need to select one specific certificate from the drop-down list, as shown in Figure 3-4. With Password as your authentication, you should enter the right user name and password in the corresponding field, as shown in Figure 3-5. Figure 3-4 Figure 3-5 3) Wireless network of None If you selected a wireless network of None (that is, no security is set.
TL-WN951N 4. 300Mbps Wireless N PCI Adapter User Guide Please wait a few minutes for the connection process. Figure 3-6 5. You have now successfully connected to your network. Click Close to enjoy the Internet. Figure 3-7 6. To view more information about the network currently connected, click Status in the tools section and the page will display information such as the network type, channel, rate, etc.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 3-8 3.2 To connect using WPS WPS (Wi-Fi Protected Setup) function allows you to add a new wireless device to an existing network quickly. If your wireless Router supports WPS or QSS (Quick Security Setup), you can establish a wireless connection between wireless card and Router using either Push Button Configuration (PBC) method or PIN method.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 3-9 3. The adapter will be connecting to the target network. Figure 3-10 4. When the following window appears, you have successfully connected to the network.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 3-11 3.2.2 PIN method There are two ways to configure the WPS by PIN method: 1) Enter the PIN from your Router or AP device. 2) Enter a PIN into your Router or AP device. ( Note: This method is only available in Windows XP and Windows Vista.) Following are the detailed configuration procedures of each way. 3.2.2.1. Enter the PIN from your Router or AP device 1. Open TWCU and click WPS tab.
TL-WN951N 2. 300Mbps Wireless N PCI Adapter User Guide The adapter will be connecting to the target network. Figure 3-13 3. When Figure 3-11 appears, you have successfully connected to the network. 3.2.2.2. Enter a PIN into your AP device Note: This method is only available in Windows XP and Windows Vista. 1. Open TWCU and click WPS tab. Select Enter the PIN of this device into my access point or wireless router.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 3-15 3. When Connect successfully appears on the screen (as shown in Figure 3-16), the WPS configuration is complete. Or you can view the adapter’s utility page to see whether the connection has been successful (as shown in Figure 3-17). Figure 3-16 Figure 3-17 3.3 To connect using Windows built-in wireless utility 3.3.1 In Windows XP Windows XP users may use the built-in wireless utility. Follow the steps below.
TL-WN951N 1. 300Mbps Wireless N PCI Adapter User Guide Right-click on the utility icon in your system tray (lower-right corner). Select Switch to Windows wireless configuration tool. Figure 3-18 Or double-click the utility icon to load the utility configuration page. Click Advanced in the tools section and then select Use Windows wireless configuration tool in the figure shown below. Click OK when Figure 3-20 appears to continue.
TL-WN951N 2. 300Mbps Wireless N PCI Adapter User Guide Right-click on the wireless computer icon in your system tray (lower-right corner). Select View Available Wireless Networks. Figure 3-21 3. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button. Figure 3-22 4. If the network is security-enabled, you will be prompted to enter the key as shown below.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide as shown in the figure below. Select Connect to a network. Figure 3-24 2. The utility will display any available wireless networks in your area. Highlight the wireless network you would like to connect and then click Connect. Figure 3-25 3. If the network you would like to connect is security-enabled, enter the same security key or passphrase that is on your Router.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 3-26 4. You have now successfully connected to the network. Figure 3-27 3.3.3 In Windows 7 Windows 7 users may use the built-in wireless utility. Follow the steps below. 1. Left-click the wireless icon in your system tray (lower-right corner). The utility will display any available wireless networks in your area. Highlight the wireless network (displayed using the SSID) to be connected and then click Connect.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 3-28 2. If the network you would like to connect is encrypted, enter the same security key or passphrase that is on your Router. Or push the WPS/QSS button on the Router or access point (You will be prompted to push the button on the window if WPS function is supported as shown in the figure below). If the network to be connected is not secure, the connection will be built without entering a key.
TL-WN951N 3. 300Mbps Wireless N PCI Adapter User Guide You have now successfully connected to the network. Figure 3-30 3.3.4 In Windows 8 Windows 8 users may use the built-in wireless utility. Follow the steps below. 1. Click the icon at the bottom of your screen, and a network list will appear at the right side of your screen. Select your target network, and then click Connect. Figure 3-31 2. If the network is unencrypted, you will directly connect to it.
TL-WN951N Note: 300Mbps Wireless N PCI Adapter User Guide Figure 3-32 You can also push the WPS/QSS button on your router as hinted “You can also connect by pushing the button on the router”. Then click Next to continue. 3. When Connected appears behind the SSID (as shown below), you have successfully connected to the target network. Figure 3-33 Note: If the adapter is connected to the network for the first time, you will be asked whether to turn on sharing or connect to devices.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 3-34 26
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Chapter 4 Management This section will show you how to configure your TL-WN781ND adapter using the TP-LINK Wireless Configuration Utility (TWCU). The TL-WN951N adapter uses the TP-LINK Wireless Configuration Utility as the management software. The utility provides users with an easy interface to change any settings related to the adapter. Double-clicking on the icon on your desktop will start the utility. 4.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 4-2 Figure 4-3 Figure 4-4 28
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 4-5 Figure 4-6 The following items can be found on the screen. Profile Name: Enter a name for your profile (e.g. CoffeeShop, Home, Office). The same name is not allowed. Please also note that no space is allowed between words. SSID: Select the target network from the drop-down list. Network Type: Select the network type. If you are connecting to a wireless router or access point, select Infrastructure.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide wireless adapter. While in ad hoc mode, it is recommended that you select WEP to secure your wireless network. Note: In Infrastructure mode, you will see Figure 4-3 if you selected the security type WEP; you will see Figure 4-4 if you selected the security type WPA-PSK/WPA2-PSK. While, if you selected the security type WPA/WPA2 (-Enterprise), Figure 4-5 or Figure 4-6 will be displayed.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 4-7 Figure 4-8 4.1.2 Modify a profile You may edit an existing profile by clicking the Modify button from the Profile page. For instance, you may like to change the profile name from Home to Home1 or you may want to specify another SSID for profile Home. After all the changes, click Save to make the changes take effect.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 4-9 4.1.3 Delete a profile To delete an existing profile, highlight the profile name and click Remove on the bottom of the screen or press the Delete button on your keyboard. When the following figure appears, click OK to continue. Figure 4-10 4.2 Advanced The following configurations can be made on the Advanced page: 1) To select wireless configuration tool.
TL-WN951N 4) 300Mbps Wireless N PCI Adapter User Guide To change the power save mode. Figure 4-11 4.3 About The About screen gives you some information about the Driver and Utility versions of the adapter. Right-click the icon in your system tray and select About from the list.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Chapter 5 SoftAP Mode (For Windows 7 and Windows 8) In Soft AP mode, the adapter will work as an AP. This function is available in Windows 7 and Windows 8. Suppose that only one computer in your house can access the Internet for various reasons like only one LAN port is available on your wired broadband Router, however, other wireless-capable devices also want to share the Internet.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 5-2 The Soft AP icon then will appear beside Advanced icon in the utility. Figure 5-3 SoftAP mode: Select to enable or disable the function. Internet Connecting Share (ICS): Specify a connection through which devices connected to your AP can access the Internet. SSID: Enter the name for your soft AP (for example, Jone) so that others can know which AP is yours when trying to connect to it. The default name (SSID) is “tp-link”.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Encryption Type: The encryption type here is set to be AES. Security Key: Enter the Key in the field to make your AP security enabled. It is recommended that you specify another key instead of the default key 12345678. Only by entering the corresponding key can other computers establish a successful connection with your AP. IP Address: Here displays the IP address of the SoftAP.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Chapter 6 Uninstall Software 6.1 In Windows XP/Vista/7 The software uninstall steps are similar in Windows XP, Windows Vista, and Windows 7, here we just use Windows 7 as an example. 6.1.1 Uninstall the utility software from your PC 1. On the Windows taskbar, click the Start button, click All programsTP-LINK, and then click Uninstall-TP-LINK Wireless Configuration Utility. 2.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 6-3 4. Click Finish when the figure below appears. Figure 6-4 6.1.2 Uninstall the driver software from your PC 1. On the Windows taskbar, click the Start button, click All programsTP-LINK, and then click Uninstall-TP-LINK TL-WN951N Driver.
TL-WN951N 2. 300Mbps Wireless N PCI Adapter User Guide Figure 6-5 Uninstall Driver Click Yes to start uninstalling the driver software from your PC. Figure 6-6 3. It may take a few minutes to undergo the whole un-installation process.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 6-7 4. Click Finish when the figure below appears. Figure 6-8 6.2 In Windows 8 6.2.1 Uninstall the utility software from your PC 1. Enter the Metro interface，right-click any blank place in the Metro interface, then App Bar will appear below the Metro interface, click All apps. Find the TP-LINK application, and click Uninstall- TP-LINK Wireless Configuration Utility.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 6-9 2. Click Yes to start uninstalling the utility software from your PC. Figure 6-10 3. It may take a few minutes to undergo the whole un-installation process. Figure 6-11 4. Click Finish when the figure below appears.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 6-12 6.2.2 Uninstall the driver software from your PC 1. Enter the Metro interface，right-click any blank place in the Metro interface, then App Bar will appear below the Metro interface, click All apps. Find the TP-LINK application, and click Uninstall-TP-LINK TL-WN951N Driver. Figure 6-13 2. Click Yes to start uninstalling the driver software from your PC. Figure 6-14 3.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Figure 6-15 4. Click Finish when the figure below appears.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Appendix A: Specifications Normal Interface 32 bit PC Interface Standards IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.1x, IEEE 802.11e, IEEE 802.11i Operating System Windows XP, Windows Vista, Windows 7, Windows 8 Throughput 300Mbps (Maximal) 11b: 1/2/5.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Appendix B: Glossary 802.11b - The 802.11b standard specifies a wireless product networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.
TL-WN951N 300Mbps Wireless N PCI Adapter User Guide Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security.
