Business Networking Solution Installation Guide Gigabit Unmanaged Switch TL-SG1048 TL-SG1024/TL-SG1024D TL-SG1016/TL-SG1016D TL-SG1008/TL-SG1008PE
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.
Related Document This Installation Guide is also available in PDF on our website. To obtain the latest documentation and product information, please visit the official website: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during the installation. This Installation Guide is structured as follows: Chapter 1 Introduction.
Contents Chapter 1 Introduction ——————————— 01 1.1 Product Overview ...................................................................01 1.2 Features ......................................................................................01 1.3 Appearance ...............................................................................02 Chapter 2 Installation ———————————— 08 2.1 Package Contents ...................................................................08 2.2 Safety Precautions ........
Gigabit Unmanaged Switch CCCCCCCCCC Introduction 1111 Product Overview The Gigabit Unmanaged Switch provides you with a high-performance, low-cost, easyto-use, seamless and standard upgrade to boost your old network to 1000Mbps. By increasing the speed of your network server and backbone connections, the Gigabit Unmanaged Switch makes Gigabit a reality. Power users in the home, office, workgroup, or creative production environment can now move large, bandwidthintensive files faster.
Gigabit Unmanaged Switch •• Supports IEEE802.3x flow control for full-duplex mode and backpressure for halfduplex transfer mode •• Non-blocking switching architecture that forwards and filters packets at full wirespeed for maximum throughput •• Supports MAC address auto-learning and auto-aging •• Desktop and rack-mountable steel case •• Internal power supply For TL-SG1008PE: •• Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3af and IEEE802.
Gigabit Unmanaged Switch 10/100/1000Mbps RJ45 Port Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding Link/Act LED. The front panel of TL-SG1024 is shown as the following figure. LEDs 10/100/1000Mbps RJ45 Port FFFFFFFFFFF Front Panel of TL-SG1024 The front panel of TL-SG1016 is shown as the following figure. LEDs 10/100/1000Mbps RJ45 Port FFFFFFFFFFF Front Panel of TL-SG1016 The front panel of TL-SG1024D is shown as the following figure.
Gigabit Unmanaged Switch The front panel of TL-SG1008 is shown as the following figure. TL-SG1008 Link Act 8-Port Gigabit Switch Power 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 8 1000Mbps LEDs 10/100/1000Mbps RJ45 Port FFFFFFFFFFF Front Panel of TL-SG1008 LEDs LED Power Link/Act 1000Mbps Status Indication On The switch is powered on. Off The switch is powered off or power supply is abnormal. On There is a device linked to the corresponding port but no activity.
Gigabit Unmanaged Switch LED PoE MAX Status Indication On (red1 The power of all the connected PoE ports is between 118W and 124W. No power may be supplied if additional PDs are connected. Flashing (red1 The power of all the connected PoE ports is >=124W. Off The power of all the connected PoE ports is <118W, or there is no PD connected to the corresponding port. On (green1 There is a 10 0 0Mbps device connec ted to the corresponding port.
Gigabit Unmanaged Switch Rear Panel The rear panel of TL-SG1048 is shown as the following figure. Power Socket Grounding Terminal FFFFFFFFFFF Rear Panel of TL-SG1048 The rear panel of TL-SG1024 is shown as the following figure. Power Socket Grounding Terminal FFFFFFFFFFF Rear Panel of TL-SG1024 The rear panel of TL-SG1016 is shown as the following figure. Power Socket Grounding Terminal FFFFFFFFFFFF Rear Panel of TL-SG1016 The rear panel of TL-SG1024D is shown as the following figure.
Gigabit Unmanaged Switch The rear panel of TL-SG1016D is shown as the following figure. Power Socket Grounding Terminal FFFFFFFFFFFF Rear Panel of TL-SG1016D The rear panel of TL-SG1008 is shown as the following figure. Grounding Terminal Power Socket FFFFFFFFFFFF Rear Panel of TL-SG1008 The rear panel of TL-SG1008PE is shown as the following figure.
Gigabit Unmanaged Switch CCCCCCCCCC Installation 2222 Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord This Installation Guide Two mounting brackets and the fittings 2222 Safety Precautions To avoid any device damage and bodily injury caused by improper use, please observe the following rules. ■■ Safety Precautions ■■ Keep the power off during the installation.
Gigabit Unmanaged Switch ■■ Site Requirements Temperature/Humidity 40℃ 0℃ Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high temperature may accelerate aging of the insulation materials and can thus significantly shorten the service life of the device. For normal temperature and humidity of the device, please check the following table.
Gigabit Unmanaged Switch Lightening Protection Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. ■■ Ensure the rack and device are well earthed. ■■ Make sure the power socket has a good contact with the ground.
Gigabit Unmanaged Switch 2222 Product Installation ■■ Desktop Installation To install the device on the desktop, please follow the steps: 111Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 222Remove the adhesive backing papers from the rubber feet. 333Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device.
Gigabit Unmanaged Switch Rack FFFFFFFFFFF Rack Installation Caution: Please set 5~10cm gaps around the device for air circulation. Please avoid any heavy thing placed on the device. Please mount devices in sequence from the bottom to top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation.
Gigabit Unmanaged Switch CCCCCCCCCC Lightning Protection 3333 Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors are different. A reasonable cabling system can decrease the damage of induced lightning to devices. Note: It's not recommended using Ethernet cables outdoors. When cabling outdoors, please use a signal lightning arrester.
Gigabit Unmanaged Switch ■■ Requirements for Cabling Indoors When cabling indoors, keep a certain distance away from the devices that may cause high-frequency interferences, such as down-conductor cable, powerline, power transformer and electromotor. ■■ ■■ The main cable should be paved in the metal raceway of the access shaft. When cabling, keep the loop area formed by the cable itself as small as possible. Requirements for the distance between Ethernet cable and other pipelines are shown in the table.
Gigabit Unmanaged Switch Cable 2~5kVA powerline >5kVA powerline Pave Way Min Parallel Length (mm1 Parallel cabling 300 One is in the grounded metal raceway or metal pipe 150 The both are in the grounded metal raceway or metal pipe 80 Parallel cabling 600 One is in the grounded metal raceway or metal pipe 300 The both are in the grounded metal raceway or metal pipe 150 Device Min Distance (m1 Switch case 1.00 Transformer room 2.00 Elevator tower 2.00 Air-conditioner room 2.
Gigabit Unmanaged Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. ■■ Connecting to the Ground via the Power Supply If the device is installed in the normal environment, the device can be grounded via the PE (Protecting Earth) cable of the AC power supply as shown in the following figure. FFFFFFFFFFF Connecting to the Ground Note: The figure is to illustrate the application and principle.
Gigabit Unmanaged Switch Grounding Terminal Equipotential Bonding Cable Ground Cable Grounding Bar FFFFFFFFFFF Equipotential Bonding When equipotential bonding, please note that the cable should be copper wrapped 2 Kelly with its area being 6mm at least. The shorter cable the better, and use a grounding bar to establish an equipotential bonding point. Note: The equipotential bonding cable and ground cable are not provided with our product. If needed, please self purchase it.
Gigabit Unmanaged Switch ■■ ■■ The port rate of the signal lightning arrester should match the rate of the desired port on the device. If it is not matched, this signal lighting arrester will not work. Purchase a standard lightning arrester. Install signal lightning arrester near the protected device and connect it to the ground via a shorter ground cable.
Gigabit Unmanaged Switch CCCCCCCCCC Connection 4444 Ethernet Port Connect a Ethernet port of the switch to the computer by RJ45 cable as the following figure shown. RJ45 Port RJ45 Cable FFFFFFFFFFF Connecting the RJ45 Port 4444 Verify Installation After completing the installation, please verify the following items: ■■ There are 5~10cm of clearance around the sides of the device for ventilation and the air flow is adequate.
Gigabit Unmanaged Switch Note: The figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. 4444 Initialization For TL-SG1048/TL-SG1024/TL-SG1024D/TL-SG1016/TL-SG1016D/TL-SG1008: After the device is powered on, it begins the Power-On Self-Test. A series of tests run automatically to ensure the device functions properly.
Gigabit Unmanaged Switch Appendix A Troubleshooting QQQQ The Power LED is not lit The Power LED should be lit up when the power system works normally. If the Power LED worked abnormally, please check as follows: 111 Make sure that the power cable is connected properly, and the power contact is normal. 222 Make sure the voltage of the power supply meets the requirement of the input voltage of the switch.
Gigabit Unmanaged Switch Appendix B Specifications Item Standards Content IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x IEEE802.3af (for TL-SG1008PE1, IEEE802.3at (for TL-SG1008PE1 UTP/STP of Cat. 3 or above(maximum 100m1 10Base-T For TL-SG1008PE: UTP category 3, 4, 5 cable (maximum 100m1 EIA/TIA-568 100Ω STP (maximum 100m1 2-pair UTP/STP of Cat.
Gigabit Unmanaged Switch Appendix C Technical Support ■■ For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq ■■ To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download ■■ 23 For all other technical support, please contact us by using the following details: Global Tel: +86 F55 2650 4400 Fee: Depending on rate of different carriers, IDD. E-mail: support@tp-link.
Gigabit Unmanaged Switch Poland Tel: +48 (01 801 080 618 +48 223 606 363 (if calls from mobile phone1 Fee: Depending on rate of different carriers. E-mail: support.pl@tp-link.com Service time: Monday to Friday, 0F:00 to 1F:00. GMT+1 or GMT+2 (DST1 France Tel: 0820 800 860 (French service1 Fee: 0.118 EUR/min from France Email: support.fr@tp-link.com Service time: Monday to Friday, 0F:00 to 18:00.
Website: http://www.tp-link.com E-mail: support@tp-link.com 7106504647 REV5.0.
