Business Networking Solution Installation Guide Unmanaged/Easy Smart Rackmountable Switches
About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods and the points that should be attended to during installation. This Installation Guide is structured as follows: Chapter 1 Introduction This chapter describes the external components of the switch. Chapter 2 Installation This chapter illustrates how to install the switch. Chapter 3 Connection This chapter illustrates how to do the physical connection of the switch.
Contents Chapter 1 Introduction–––––––––––––––––––––––– 1 1.1 1.2 Product Overview.............................................................. 1 Appearance......................................................................... 1 Chapter 2 Installation––––––––––––––––––––––––– 9 2.1 Package Contents............................................................. 9 2.3 Installation Tools................................................................ 11 2.2 2.4 Safety Precautions......................
Unmanaged/Easy Smart Rackmountable Switches Chapter 1 Introduction 1.1 Product Overview The Unmanaged/Easy Smart Switch provides you with a low-cost, easy-to-use, high-performance, seamless, and standard upgrade to improve your network to 100 Mbps or 1000 Mbps. TL-SG1008MP/TL-SG1016PE/TL-SG1218MPE is also a Power Sourcing Equipment (PSE*).
Unmanaged/Easy Smart Rackmountable Switches The front panel of TL-SF1016 is shown as the following figure. Figure 1-3 Front Panel of TL-SF1016 10/100Mbps RJ45 Port LEDs The front panel of TL-SF1016DS is shown as the following figure. Figure 1-4 Front Panel of TL-SF1016DS 10/100Mbps RJ45 Port LEDs The front panel of TL-SG1016 is shown as the following figure. Figure 1-5 Front Panel of TL-SG1016 LEDs 10/100/1000Mbps RJ45 Port The front panel of TL-SG1016D is shown as the following figure.
Unmanaged/Easy Smart Rackmountable Switches The front panel of TL-SG1016S is shown as the following figure. Figure 1-7 Front Panel of TL-SG1016S LEDs 10/100/1000Mbps RJ45 Port The front panel of TL-SG1016DE is shown as the following figure. Figure 1-8 Front Panel of TL-SG1016DE LEDs Reset 10/100/1000Mbps RJ45 Port The front panel of TL-SG1016PE is shown as the following figure.
Unmanaged/Easy Smart Rackmountable Switches The front panel of TL-SF1024D is shown as the following figure. Figure 1-11 Front Panel of TL-SF1024D LEDs 10/100Mbps RJ45 Port The front panel of TL-SG1024 is shown as the following figure. Figure 1-12 Front Panel of TL-SG1024 LEDs 10/100/1000Mbps RJ45 Port The front panel of TL-SG1024D is shown as the following figure. Figure 1-13 Front Panel of TL-SG1024D LEDs 10/100/1000Mbps RJ45 Port The front panel of TL-SG1024S is shown as the following figure.
Unmanaged/Easy Smart Rackmountable Switches The front panel of TL-SG1024DE is shown as the following figure. Figure 1-15 Front Panel of TL-SG1024DE LEDs Reset 10/100/1000Mbps RJ45 Port The front panel of TL-SF1048 is shown as the following figure. Figure 1-16 Front Panel of TL-SF1048 10/100Mbps RJ45 Port LEDs The front panel of TL-SG1048 is shown as the following figure.
Unmanaged/Easy Smart Rackmountable Switches LED Indication Power Off: The switch is powered off or power supply is abnormal. PWR On: The switch is powered on. Flashing: Power supply is abnormal. Note: PWR for TL-SG1016PE/TL-SF1024/TL-SG1218MPE; Power for other switches. On: Running at 1000 Mbps. 1000Mbps Off: Running at 10/100 Mbps or no device is linked to the corresponding port.
Unmanaged/Easy Smart Rackmountable Switches LED Indication On: Total power supply is between 146 W and 153 W. No power may be supplied if additional PDs are connected. Flashing: Total power supply is equal to or greater than 153 W. Off: Total power supply is less than 146 W. Note: Only for TL-SG1008MP. PoE Max On: Total power supply is between 143 W and 150 W. No power may be supplied if additional PDs are connected. Flashing: Total power supply is equal to or greater than 150 W.
Unmanaged/Easy Smart Rackmountable Switches ■■ Rear Panel The rear panel is shown as the following figure. Here we take TL-SG1016PE as an example. Figure 1-19 Rear Panel Kensington Security Slot Kensington Security Slot Power Socket Grounding Terminal Secure the lock (not provided) into the security slot to prevent the device from being stolen. Note: Only TL-SG1016PE and TL-SG1218MPE has a kensington security slot. Grounding Terminal The switch already comes with lightning protection mechanism.
Unmanaged/Easy Smart Rackmountable Switches Chapter 2 Installation 2.1 Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, contact your distributor. One Switch One Power Cord This installation Guide Business Networking Solution Installation Guide One Resource CD Two mounting brackets, eight screws and four rubber feet Note: The resource CD is only for TL-SG1016DE/TL-SG1016PE/TL-SG1024DE/TL-SG1218MPE. 2.
Unmanaged/Easy Smart Rackmountable Switches Site Requirements ■■ Temperature/Humidity 40°C 0°C Keep the equipment room at an appropriate level of temperature and humidity. Too much or too little humidity may lead to bad insulation, leakage of electricity, mechanical property changes, and corrosion. High temperatures may accelerate aging of the insulation materials, significantly shortening the service life of the device.
Unmanaged/Easy Smart Rackmountable Switches Extremely high voltage currents can be produced instantly when lightning occurs and the air in the electric discharge path can be instantly heated up to 20,000 °C. As this instant current is strong enough to damage electronic devices, more effective lightning protection measures should be taken. ■■ ■■ ■■ ■■ Ensure that the rack and the device are well earthed. Make sure the power socket has a good contact with the ground.
Unmanaged/Easy Smart Rackmountable Switches Figure 2-1 Desktop Installation Feet Bottom of the Device Notch ■■ Rack Installation To install the device in an EIA standard-sized, 19-inch rack, follow the instructions described below: 1. Check the efficiency of the grounding system and the stability of the rack. 2. Secure the supplied rack-mounting brackets to each side of the device with supplied screws, as illustrated in the following figure.
Unmanaged/Easy Smart Rackmountable Switches Chapter 3 Connection 3.1 Ethernet Port Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shows. Figure 3-1 Connecting the RJ45 Port RJ45 Port 3.2 RJ45 Cable SFP Port The following figure demonstrates the connection of SFP port to an SFP module. Figure 3-2 Inserting the SFP Module SFP Slot SFP Module Note: TL-SG1218MPE features 2 individual SFP por ts which suppor t 1000M SFP module connection only. 3.
Unmanaged/Easy Smart Rackmountable Switches ■■ ■■ The power socket, device and rack are well grounded. The device is correctly connected to other network devices. 3.4 Power On Plug the negative connector of the provided power cord into the power socket of the device and plug the positive connector into a power outlet as the following figure shows. Figure 3-3 Connecting to Power Supply Note: The figure is to illustrate the application and principle.
Unmanaged/Easy Smart Rackmountable Switches 2. Configure IP address on your PC to make sure the switch and PC are in the same subnet. ■■ ■■ If the switch uses an IP address assigned by a DHCP server, set your PC to obtain an IP address automatically from the DHCP server. If the switch uses the static IP address of 192.168.0.1, configure your PC’s IP address as 192.168.0.x (”x” ranges from 2 to 254), and subnet mask as 255.255.255.0. 3. Launch a web browser on your PC.
Unmanaged/Easy Smart Rackmountable Switches Appendix A Troubleshooting Q1. What could I do if I forgot the username and password of the Switch? With the switch powered on, press the Reset button for at least 5 seconds to reset the system. The system will be reset to the factory default settings, and the default login user name and password are both admin. Q2. What should I do if I cannot access the web management page? Please try the following: 1. 2. 3. 4. 5.
Unmanaged/Easy Smart Rackmountable Switches Appendix B Specifications Item Content IEEE 802.3i, IEEE 802.3u, IEEE 802.3x IEEE 802.3ab (except TL-SF1016/TL-SF1016DS/TL-SF1024/TL-SF1024D/ TL‑SF1048) Standards IEEE 802.1p (for TL-SG1008/ TL-SG1008MP/ TL-SG1016/ TL-SG1016D/ TL‑SG1016DE / TL-SG1016PE / TL-SG1016S/ TL-SG1024/ TL-SG1024D/ TL‑SG1024DE/TL-SG1024S) IEEE 802.1q (for TL-SG1016DE/TL-SG1016PE/TL-SG1024DE) IEEE 802.3af (for TL-SG1008MP/TL-SG1016PE/TL-SG1218MPE) IEEE 802.
Unmanaged/Easy Smart Rackmountable Switches LEDs Power, Link /Act (for TL-SF1016/TL-SF1016DS/TL-SF1024/TL-SF1024D/ TL‑SF1048/TL-SG1048) Power, 1000 Mbps, Link/Act, PoE Status, PoE MAX (for TL-SG1008MP) PWR, Speed, PoE Status, PoE MAX, FAN (for TL-SG1016PE) PWR, Link/Act, PoE Status, PoE MAX, FAN (for TL-SG1218MPE) Power, 1000 Mbps, Link/Act (for other switches) Operating Temperature 0°C to 40°C (32°F to 104°F) 0°C to 50°C (32°F to 122°F) (for TL-SG1008MP/TL-SG1218MPE) Storage Temperature -40°C to 70°C
FCC Compliance Information Statement Product Name: Unmanaged/Easy Smart Rackmountable Switch Model Number: TL-SG1008/TL-SG1008MP/TL-SF1016/TL-SF1016DS/TL-SG1016/TL-SG1016D/ TL-SG1016S/TL-SG1016DE/TL-SG1016PE/TL-SF1024/TL-SF1024D/TL-SG1024/TL-SG1024D/ TL-SG1024S/TL‑SG1024DE/TL-SF1048/TL-SG1048/TL‑SG1218MPE Responsible party: TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp-link.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2019/11/13 CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
BSMI Notice 安全諮詢及注意事項 ■■ 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品 . ■■ 注意防潮,請勿將水或其他液體潑灑到本產品上 . ■■ ■■ ■■ ■■ 清潔本產品之前請先拔掉電源線 . 請勿使用液體、噴霧清潔劑或濕布進行清潔 . 插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口 . 請勿將本產品置放於靠近熱源的地方 . 除非有正常的通風,否則不可放在密閉位置中 . 請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作 . 此為甲類資訊技術設備,于居住環境中使用時,可能會造成射頻擾動,在此種情況下,使用者會被要 求採取某些適當的對策 . 限用物質含有情況標示聲明書 產品元件名稱 PCB 外殼 電源供應板 限用物質及其化學符號 鉛 Pb 鎘 Cd 汞 Hg 六價鉻 CrVI 多溴聯苯 PBB 多溴二苯醚 PBDE ○ ○ ○ ○ ○ ○ ○ — ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 備考 1. " 超出 0.1 wt %" 及 " 超出 0.
Safety Information ■■ Keep the device away from water, fire, humidity or hot environments. ■■ Place the device with its bottom surface downward. ■■ Do not attempt to disassemble, repair, or modify the device. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk. この装置は、クラス A 情報技術装置です . この装置を家庭環境で使用すると電波妨害を引き起こす ことがあります .
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-Link Technologies Co., Ltd. Copyright © 2019 TP-Link Technologies Co., Ltd.
To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community. For technical support, the user guide and other information, please visit https://www.tp-link.com/support, or simply scan the QR code. If you have any suggestions or needs on the product guides, welcome to email techwriter@tp-link.com.cn. © 2019 TP-Link 7106508570 REV13.3.