TX-6610 1-Port Gigabit GPON Terminal REV: 3.0.
COPYRIGHT & TRADEMARKS is a registered trademark of Specifications are subject to change without notice. TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。 ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。 ●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 1-Port Gigabit GPON Terminal Model No.
CONTENTS Chapter 1. Product Overview ...................................................................................1 1.1 Product Overview ..........................................................................................................1 1.2 Main Features ...............................................................................................................1 1.3 Panel Layout .................................................................................................................
TX-6610 1-Port Gigabit GPON Terminal User Guide Chapter 1. Product Overview Thank you for choosing the TX-6610 1-Port Gigabit GPON Terminal. 1.1 Product Overview TP-LINK’s TX-6610 is a next-generation Gigabit Passive Optical Network (GPON) terminal, ideal for Fiber to the Home solution. It’s an incredibly robust device allowing users to access high-speed internet connections via its GPON port and share it with a Gigabit Ethernet port. With the transmission rates of up to 2.
TX-6610 1-Port Gigabit GPON Terminal User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The GPON Terminal’s LEDs are located on the front panel. They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Power GPON LOS Status Indication On Power is on. Off Power is off. On The Terminal is registered with the ISP. Flashing The Terminal is trying to register with the ISP. Off The Terminal is not yet registered with the ISP.
TX-6610 On LAN Flashing Off 1-Port Gigabit GPON Terminal User Guide A device is connected to the LAN port. The LAN port is transmitting or receiving data. No device is connected to the LAN port. 1.3.2 The Back Panel Figure 1-2 ON/OFF: The switch for the power. POWER: The Power plug is where you will connect the power adapter. RESET: There are two ways to reset the Terminal's factory defaults.
TX-6610 1-Port Gigabit GPON Terminal User Guide Chapter 2. Connecting the Terminal 2.1 System Requirements Broadband Internet Access Service (GPON). PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. TCP/IP protocol on each PC. Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 2.2 Installation Environment Requirements The Product should not be located where it will be exposed to moisture or excessive heat.
TX-6610 1-Port Gigabit GPON Terminal User Guide Figure 2-1 5
TX-6610 1-Port Gigabit GPON Terminal User Guide Chapter 3. Quick Installation Guide 3.1 TCP/IP Configuration After you directly connect your PC to the Terminal TX-6610 or connect your adapter to a Hub/Switch which has connected to the Terminal, you need to configure your PC’s IP address. We use the procedures in Windows 7 as an example, for other systems refer to T4 for instructions. Step 1: Right-click Network icon(e.g.
TX-6610 1-Port Gigabit GPON Terminal User Guide Step 3: In the prompt page that showed below, double click on the Internet Protocol Version 4 (TCP/IPv4).
TX-6610 1-Port Gigabit GPON Terminal User Guide Step 4: Select both Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. Figure 3-3 Step 5: Back to previous interface, click OK to save the settings. Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd or command in the field and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter.
TX-6610 1-Port Gigabit GPON Terminal User Guide Figure 3-5 You can check it following the steps below: 1) Is the connection between your PC and the Terminal correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Terminal's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.
TX-6610 1-Port Gigabit GPON Terminal User Guide 2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy. Go to Tools menu→Internet Options→Connections→LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 2. After your successful login, you will see the Login screen as shown in Figure 3-8. Click Network Setting PON Certification to complete the PON setting.
TX-6610 1-Port Gigabit GPON Terminal User Guide Chapter 4. Configuring the Terminal This chapter will show each Web page's key function and the configuration way. 4.1 Login After your successful login, you will see the main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below. 4.
TX-6610 1-Port Gigabit GPON Terminal User Guide Figure 4-1 12
TX-6610 1-Port Gigabit GPON Terminal User Guide System Status: Here shows the system information of the Terminal. LAN: The current port status of the Terminal. PON: Here shows the Terminal’s current GPON module information. Statistics: Here you can view the statistics of the Terminal. Click Refresh to update this page. 4.3 Network Setting Choose “Network Setting”, there are three submenus under the main menu.
TX-6610 1-Port Gigabit GPON Terminal User Guide GPON Password Old Password: Displays the factory default password. New Password: Enter the password provided by your ISP. Click Save to make the settings take effect. GPON SN Old SN: Displays the factory default SN. New SN: Enter the SN provided by your ISP. Click Save to make the settings take effect. 4.3.2 VLAN Setting Choose “Network Setting”“VLAN Setting”, the VLAN Setting screen will appear on the page as shown in Figure 4-3.
TX-6610 1-Port Gigabit GPON Terminal User Guide 4.3.3 LAN Setting Choose “Network Setting”“LAN Setting” menu and you will see the LAN screen as shown in Figure 4-4. You can change the LAN IP address on this page. Figure 4-4 LAN IP Address and Mask: IP Address: Enter the Terminal’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1. Mask: Enter the Terminal’s Subnet Mask, the default value is 255.255.255.0.
TX-6610 1-Port Gigabit GPON Terminal User Guide 4.4 Management Choose menu “Management”, and you will see the submenus under the main menu: User management, Firmware Upgrade, Factory Defaults and Reboot. Click any one of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.4.
TX-6610 1-Port Gigabit GPON Terminal User Guide 4.4.2 Firmware Upgrade Choose menu “Management” “Firmware Upgrade”, and then you can update the latest version of firmware for the Terminal on the following screen. Figure 4-6 To upgrade the Terminal's firmware, follow the instructions below: 1) Download a most recent firmware upgrade file from our website (www.tp-link.com). 2) Type the path and file name of the update file into the “File Path” field.
TX-6610 1-Port Gigabit GPON Terminal User Guide 4.4.3 Factory Defaults Choose menu “Management” “Factory Defaults” and then you can restore the configurations of the Terminal to its factory defaults on the following screen. Figure 4-7 Also erase current PON settings: Check this box, the current PON settings will be deleted when you restore the configurations of the Terminal to its factory defaults. Click the Restore button to reset all configuration settings to their default values.
TX-6610 1-Port Gigabit GPON Terminal User Guide Appendix A: Specifications General Standards and Protocols 802.3, 802.3u, 802.3ab, 802.1p, 802.1q, ITU-T G.984.1, G.984.2, G.984.3, G.984.
TX-6610 1-Port Gigabit GPON Terminal User Guide Appendix B: Troubleshooting T1. How to establish a dial-up connection to connect to the Internet? Run the dialing software such as WinPoet or EnterNet to do the virtual dialing as the following described. For Mac OS X 1) Click the Apple icon on the upper left corner of the screen. 2) Go to “System Preferences > Internet & Wireless > Network” and then select Ethernet. 3) In the Configure IPv4 box, select Create PPPoE Service.
TX-6610 1-Port Gigabit GPON Terminal User Guide 4) Click Broadband (PPPoE). 5) Enter the User name and Password given by your ISP, and type a Connection name to identify your connection, and then click Connect. T2. How do I restore my Terminal to its factory default settings? Once the Terminal is reset, the current settings will be lost and you will need to reconfigure it. We strongly suggest you back up the current settings before resetting the Terminal.
TX-6610 1-Port Gigabit GPON Terminal User Guide T5. What can I do if I cannot access the web management page? 1) Make sure that the computer is properly connected to the Terminal via the Ethernet cable. 2) Make sure that the computer connected to the Terminal is set to obtain an IP address automatically. Refer to T4 for instructions. 3) Make sure that http://192.168.1.1 is correctly entered, or use another web browser and try again. 4) Disable then enable the network adapter being used.
