User Manual

ManualsBrandsTPI ManualsCeiling Mounted HeatersRadiant Ceiling Panel 24"L x 24"W 250W 277V

1 of 7REV 11/15/18 ECO 1-7483 FORM: 9688

GENERAL INFORMATION:

Wiring: Check voltage on nameplate of heater to make sure it conforms with supply voltage. 277 volt heaters

operated at 240 volt and 240 volt heaters operated at 208 volts will give a capacity of 75% rated wattage.

All wiring must conform to the N.E.C./C.E.C. and existing local code requirements.

Location: Heaters are intended for ceiling mount only. If the situation requires, heating panels may be installed

directly adjacent to walls and to other heating panels.

WARNING: Adhere to all applicable building codes and regulations when installing or using ceiling

heaters. Failure to do so could cause improper activation of re suppression systems leading to property

damage or bodily injury.

AVERTISSEMENT: respecter tous les codes et réglementations applicables lors de l’installation ou de

l’utilisation de radiateurs de plafond. L’omission de le faire pourrait entraîner une mauvaise activation

des systèmes de suppression des incendies entraînant des dommages matériels ou corporels.

Controls: Heaters may be controlled by a wall mounted line voltage or pilot duty thermostat, timer or other

suitable device. (Controls are not supplied with heaters).

Insulation: Insulation is built into the ceiling heaters above the heating element surface to reduce heat loss

through the ceiling and deect the heat downward into the heated space. Additional insulation placed in the

ceiling is highly recommended to further reduce the upward passage of heat.

Handling Panels are factory supplied in a white egg shell textured nish to match surrounding ceiling areas as

closely as possible. Since this nish is more difcult to clean than a high gloss type, it is suggested that the

installer wear clean gloves to prevent unnecessary soiling.

CLEANING/MAINTENANCE

Cleaning should be done with a vacuum cleaner and soft brush attachment. Gently go over the face of the panel

and remove any dust or lint. There is no other maintenance required for the heater.

INSTALLATION

INSTRUCTIONS

CP & RCP Series

Radiant Ceiling Panel Heaters

Summary of content (7 pages)

PAGE 1
CP & RCP Series Radiant Ceiling Panel Heaters INSTALLATION INSTRUCTIONS GENERAL INFORMATION: Wiring: Check voltage on nameplate of heater to make sure it conforms with supply voltage. 277 volt heaters operated at 240 volt and 240 volt heaters operated at 208 volts will give a capacity of 75% rated wattage. All wiring must conform to the N.E.C./C.E.C. and existing local code requirements. Location: Heaters are intended for ceiling mount only.
PAGE 2
Model No.
PAGE 3
Panel Size FRAME OUT SIZE Model No.
PAGE 4
IMPORTANT INSTRUCTIONS 1. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 2. Read all instructions before using this heater. 3. CAUTION: High temperature, risk of fire, keep electrical cords, drapery, furnishings and other combustibles at least 3 feet (0.9m) from the front of the heater. Zero clearance on sides and rear.
PAGE 5
R LY FO G E ON IN FRAM ED HEAT SS RECE PANELS WITH NEL G PA OUNT N I T HEA FACE M SUR RAME F G NTIN MOU BAR E C A " SURF E FOR "T NEL FRAM NG CP PA I HEA T NG UNTI E MO C A F SUR FRAME FRAME DEPTH = 3" RECESSED PANEL FRAME ACCESSORY FOR USE WITH RECESSED PANELS ONLY NOMINAL SIZE 22” X 22” (559MM X 559MM) 22” X 48” (550MM X 1219MM) SURFACE MOUNTED FRAME ACCESSORY FOR SURFACE MOUNTED PANELS CATALOG NUMBERS NOMINAL SIZE SF200 24” X 24” (610MM X 610MM) SF400 24” X 48” (610MM X 1219MM) Frame is const
PAGE 6
WIRING INFORMATION IMPORTANT INFORMATION: READ BEFORE CONNECTING TO POWER SUPPLY 1. Disconnect branch circuit or power supply before connecting or servicing. 2. All wiring must be done in accordance with the N.E.C./C.E.C., or local code having jurisdiction. 3. Do not cover face of heater at any time with an object, other construction or furnishing as over heating could result and combustion of objects. 4. Check to determine that branch circuit voltage is the same as voltage shown on panel data label.
PAGE 7
RECESSED CEILING PANELS The recessed ceiling panels are designed to be used with a recessed frame (included with recessed panels) designed to fit the cutout in the ceiling. Ref. Fig. 2. The cutout dimensions are as given in the specification table for the specific panel model in column D and E. Ref. Fig. 3. The frame must be secured to the framing members as shown in Fig. 4 using wood screws or nails.