TR89250 OPERATOR’S MANUAL 1700 LISTED E498391 WATT DIGITAL HEAT GUN POWER Double Insulated Your digital heat gun has been engineered and constructed to be easy to use, dependable, and safe. With the right care, it can take care of your digital heat gun for years to come. WARNING: Please read and understand this manual in its entirety before using the product. Doing so can reduce the risk of injury. SAVE THIS MANUAL FOR FUTURE REFERENCE Email: support@trindustrial.
TABLE OF CONTENTS • Specifications............................................................................................................................................................. 2 • Packing List................................................................................................................................................................ 2 • General Safety Rules..................................................................................................................
GENERAL SAFETY RULES • TAKE CARE OF YOUR LUNGS. Wear a face or dust mask if the operation is dusty. WARNING: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS. Electrical shock, fire, and/or serious personal injury may result from failure to follow all instructions listed below. • TAKE CARE OF YOUR HEARING. Wear hearing protection if working with loud equipment and/or tools. • TAKE CARE OF YOUR ELECTRICAL CORD. Never carry tool by the cord or yank it to disconnect from receptacle.
• ONLY USE THE ACCESSORIES recommended in the manual. Use of accessories that are not listed may cause injury. • STAY ALERT AT ALL TIMES! Do not allow familiarity (gained from frequent use of your tool) to cause a careless mistake. ALWAYS REMEMBER that a careless fraction of a second is sufficient to inflict severe injury. • KEEP TOOL AWAY FROM OIL AND GREASE AND AS DRY AS POSSIBLE. Always use a clean cloth when cleaning.
10. Mop the floors well with detergent once the job is complete. protective clothing and wash areas with soap and water. Allowing dust to get into your mouth, eyes or lay on the skin may promote absorption of harmful chemicals. 11. Keep a double plastic bag handy to place paint chips and debris into. Dispose of it properly. 12. Remove your protective clothing in the work area after work is done to avoid bringing it into other environments.
ELECTRICAL ELECTRICAL CONNECTION WARNING: This appliance has a polarized plug (one The precision built electric motor should be connected to a power supply that is 120 volts/60Hz AC only. Do not operate this product on DC. If there is a substantial drop in voltage, it may lose power, causing the motor to overheat. If the product does not operate when plugged into an outlet, check on the power supply. blade is wider than the other).
OPERATIONS SWITCHING ON AND OFF TEMPERATURE AND AIR FLOW SETTINGS 1. The power switch has three settings: 0 (off), I (standby/cool down), and II (on). 1. 2. To turn the tool on, set the switch from 0 to I or from 0 to II. It is normal that some smoke might be emitted after switching on. Set the power switch to setting I and the tool enters the standby/cool down mode.
PAINT REMOVAL Proper paint removal is in fact quite a developed skill. A few simple projects should help you refine your technique. Start by turning on the heat gun and holding it with the nozzle around one inch from the surface you’re planning to strip. The paint should start to blister once it’s ready to be stripped. You can then scrape it with even, smooth strokes.
INCLUDED ATTACHMENTS Accessories could be used with the heat gun for dierent applications. Accessory Description Purpose Fan Nozzle For wider distribution of hot air, mostly for wider surfaces such as doors and floors. Glass Protector Safer to use near glass as it distributes heat away from the area that needs to be protected. Cone Nozzle For more precision, this nozzle concentrates; the air into a smaller area.
WARRANTY Limited Warranty Statement The TR Industrial limited warranty covers the original purchaser’s product in the event that genuine defects resulting from materials or workmanship is discovered. Your product will be either repaired or replaced if such conditions are verified. This warranty does not cover any TR Industrial product that has been subjected to misuse, neglect, negligence or accidents. It is not covered if it is rented out to third parties.
WARRANTY CARD DIGITAL HEAT GUN MODEL: TR89250 PRODUCT SERIAL NUMBER: DATE OF PURCHASE: PLACE OF PURCHASE: (RETAILERS NAME) NAME: STREET ADDRESS: CITY: STATE: ZIP CODE: PHONE: EMAIL: Instructions: Fill in the information above and mail in with a copy of the sales receipt when registering warranty. TR INDUSTRIAL 1788 W 2nd Street, Pomona, CA 91766 (888) 446-6088 | support@trindustrial.com | www.TRIndustrial.com 11 VER.
www.TRIndustrial.
