User Manual

ManualsBrandsTrackStar ManualsHobby1/5 Brushless Sensorless Car ESC w/15A BEC

FEATURES

INTRODUCTION

INSTRUCTION MANUAL

Thank you for purchasing TRACKSTAR 1/5 Brushless Sensorless Car ESC. Please read the

Instruction Manual thoroughly before you use the product. These operating instructions are

designed to ensure that you can quickly reference its features and functions and make fully use

of this product.

1/5 Brushless Sensorless Car ESC

Built-in powerful BEC. Output voltage is adjustable 6.0V or 7.4V.

Maximum output current up to 15A.

LiPo battery support up to 8 cells.

Data Logging : The controller’s parameters can be record such as your battery volts/amps

draw, motor rpm, and controller temperature. This is a good way to make sure that the rest of

your setup is performing well within its limits.

Red copper connectors are used to decrease the internal resistance in high current situations.

Heat transfer : Internal resistance is reduced by laminated copper stack control technology so

dynamic thermal equilibrium is achieved.

Safety features : low voltage protection, motor and ESC overheat protection and signal lost

protection.

The ESC can be programmed by TrackStar Multi-Function Smart Program Box

(SKU# 9052000048) The ESC firmware can be updated by connecting the ESC to computer

via smart program box.

Summary of content (10 pages)

PAGE 1
/5 Brushless Sensorless Car ESC INSTRUCTION MANUAL INTRODUCTION Thank you for purchasing TRACKSTAR 1/5 Brushless Sensorless Car ESC. Please read the Instruction Manual thoroughly before you use the product. These operating instructions are designed to ensure that you can quickly reference its features and functions and make fully use of this product. FEATURES Built-in powerful BEC. Output voltage is adjustable 6.0V or 7.4V. Maximum output current up to 15A. LiPo battery support up to 8 cells.
PAGE 2
SAFETY NOTE This product is not a toy and suitable for users older than 14 years old only. Never allow water, moisture, oil or other foreign materials to get inside ESC, motor, or on the PC Boards. It may damage your ESC. Never disassemble the ESC and modify the components on the PC Boards. Suggest using the original wires and connectors which are packed in the box. When you are doing soldering work, do not heating a same spot for more than 5 seconds as some components will get damaged by high temperature.
PAGE 3
PREPARATION 1) Plan Speed Control Placement Choose a location for the speed control that is protected from road debris. To prevent radio interference, place the ESC far away from the radio receiver and keep the power wires as short as possible. Select a location that has good airflow ventilating. If the ESC gets air flow, it will run cooler; and that means it will be more efficient. 2) Mount Speed Control in V ehicle For best choice we recommand you to use screws to mount the ESC to the chassis.
PAGE 4
CONNECTION 1) Connect ESC Throttle lead to Receiver in Channel 2. 2) Connect the motor to ESC. 3) Connect ESC to battery pack. Red power wire (battery positive) Battery Pack Black power wire (battery negative) Throttle lead Power Switch Receiver ESC CALIBRATION Calibration is necessary when the ESC powering on very first time, or whenever used with a new/different transmitter. Individual transmitter’s signals for full throttle, full brake and neutral are different.
PAGE 5
Hold full throttle and press the ESC switch button once, the green LED will blink twice then extinguish and the motor will ring twice like beep-beep which indicates the full throttle position has been set. Move the throttle trigger to full brake and hold it, press the ESC switch button once, the green LED will blink three times then extinguish and the motor will ring three times like beep-beep-beep which indicates the full brake position has been set.
PAGE 6
ESC PROGRAMMING The ESC can be programmed directly with the TrackStar Multi-Function Smart Program Box (SKU# 9052000048) or on a PC via the program box. Red power wire (battery positive) Battery Pack Black power wire (battery negative) Power Switch Programmable Items and Description Section General Setting Throttle Control Program Item Description Running Mode Forward/Brake Forward/Brake/Reverse Motor Direction Normal Reverse Speed 25-100% (in 1% increment) Voltage Cutoff 9.6-42V (in 0.
PAGE 7
Brake Control Drag Brake 0-100%(in 1% increment) Brake Strength 0-100% Initial Brake Drag Brake Brake Rate Switch Point 1-99%(in 1% increment) 1st Stage Brake Rate 1-20 2nd Stage Brake Rate 1-20 Brake Input Curve Line Mode Data Storage Start and Stop Control Choose data types to save Data Saving Time increment 0-50% Custom Single Cycle Start storage once entering Press control storage entering in main program in main program Voltage Current Throttle Current ESC RPM Temperature 0.
PAGE 8
Throttle Control Punch Rate Switch Point 50% 1st Stage Punch Rate 5 2nd Stage Punch Rate 5 TH Input Curve Line Throttle Dead Band 0.
PAGE 9
WARRANTY AND SERVICE The TRACKSTAR 1/5 Brushless Sensorless Car ESC is guaranteed to be free from defects in materials or workmanship for a period of 90 DAYS from the original date of purchase (verified by dated, itemized sales receipt).
PAGE 10
NOTES 10