Data Sheet

ManualsBrandsTRACOPOWER ManualsPSU ComponentsDC/DC converter (print) 24 Vdc 2000 mA 30 W No. of outputs: 1 x

ht tp://www.tracopower.com Page 1 of 4

DC/DC Converter THM 30WI Series, 30 Watt

The THM 30WI series is a range of medical 30 Watt DC/DC converters in 2.0”

x 1.0” plastic package and with wide 4:1 input voltage range. They provide a

reinforced isolation system for 5000 VACrms isolation and a very low leakage

current of less than 2.5 A. The units are approved to IEC/EN/ES 60601-1 3rd

edition for 2  MOPP (Means Of Patient Protection) and come along with an

ISO 14971 risk management ﬁle. Design and production conform to the quality

management system ISO 13485. With a high efﬁciency of up to 90% and highest

grade components the converters can reliably operate in an ambient tempera-

ture range of –40°C up to +80°C. They constitute a reliable solution not only for

medical equipment but also for demanding ranges of application such as trans-

portation, control & measurement or IGBT drivers.

• Ultra wide 4:1 input voltage 30 W DC/DC

converter in a 2  1 ” plastic case

• I/O isolation 5000 VACrms rated for

250 VACrms working voltage

• Certiﬁcation according to IEC/EN/ES

60601-1 3rd edition for 2MOPP

• Risk management process according to

ISO 14971 including risk management ﬁle

• Acceptance criteria for electronic

assemblies according to IPC-A-610 Level 3

• Low leakage current < 2.5 A

• Extended operating temperature range

–40°C to 80°C.

• EMC compliance to IEC 60601-1-2 4th

edition and EN55032 class A

• Operating up to 5000m altitude

• 5 year product warranty

Order code Input voltage range Output voltage Output current max. Efﬁciency typ.

THM 30-2411WI

5.0 VDC 6000 mA 88.0 %

THM 30-2412WI

12 VDC 2500 mA 89.0 %

THM 30-2413WI

9.0 – 36 VDC

15 VDC 2000 mA 89.0 %

THM 30-2415WI (24 VDC nominal)

24 VDC 1250 mA 89.0 %

THM 30-2421WI

±5 VDC ±3000 mA 86.0 %

THM 30-2422WI

±12 VDC ±1250 mA 89.0 %

THM 30-2423WI

±15 VDC ±1000 mA 89.0 %

THM 30-4811WI

5.0 VDC 6000 mA 89.0 %

THM 30-4812WI

12 VDC

2500 mA

89.0 %

THM 30-4813WI

18 – 75 VDC

15 VDC 2000 mA 89.0 %

THM 30-4815WI (48 VDC nominal)

24 VDC 1250 mA 89.0 %

THM 30-4821WI

±5 VDC ±3000 mA 86.5 %

THM 30-4822WI

±12 VDC ±1250 mA 90.0 %

THM 30-4823WI

±15 VDC ±1000 mA 89.5 %

Models

ES 60601-1

C B

Scheme

IEC 60601-1

Summary of content (4 pages)

PAGE 1
DC/DC Converter • • • • • • • • • • THM 30WI Series, 30 Watt Ultra wide 4:1 input voltage 30 W DC/DC converter in a 2 x 1 ” plastic case I/O isolation 5000 VACrms rated for 250 VACrms working voltage Certification according to IEC/EN/ES 60601-1 3rd edition for 2xMOPP Risk management process according to ISO 14971 including risk management file Acceptance criteria for electronic assemblies according to IPC-A-610 Level 3 CB Scheme IEC 60601-1 Low leakage current < 2.
PAGE 2
THM 30WI Series, 30 Watt Input Specifications Input current no load 24 Vin models: 13 mA typ. 48 Vin models: 10 mA typ. Surge voltage (3 s max.) 24 Vin models: 50 V max. 48 Vin models: 100 V max. Start-up voltage 24 Vin models: 9 VDC (or lower) 48 Vin models: 18 VDC (or lower) Startup time 60 ms max. (30 ms typ.) Under voltage shut down (lock-out circuit) 24 Vin models: 7.8 - 8.6 VDC 48 Vin models: 15.8 - 17.
PAGE 3
THM 30WI Series, 30 Watt General Specifications Overvoltage protection (±)5.0 VDC models: (±)12 VDC models: (±)15 VDC models: 24 VDC models: Capacitive load –Single output –Dual output 5.0 VDC models: 12 VDC models: 15 VDC models: 24 VDC models: ±5 VDC models: ±12 VDC models: ±15 VDC models: Temperature ranges 6.2 VDC typ. 15 VDC typ. 20 VDC typ. 30 VDC typ. 7‘200 µF max. 1‘200 µF max. 1‘000 µF max. 375 µF max. 3‘600 µF max. (each output) 750 µF max. (each output) 500 µF max.
PAGE 4
THM 30WI Series, 30 Watt Outline Dimensions (0.20) (0.20) 5 (0.40) 5.6 (0.22) 4 50.8 (2.00) 1 45.72 (1.80) 2 10.2 (0.10) 5.08 5.08 2.54 25.4 (1.00) Pinout Pin 1 2 3 4 5 Single +Vin (Vcc) –Vin (GND) +Vout –Vout Trim Dual +Vin (Vcc) –Vin (GND) +Vout Commom –Vout Dimensions in [mm], () = Inch Tolerances ±0.5 (±0.02) ±0.25 (±0.01) Pin pich tolerances ±0.25 (±0.01) Pin ø 1.0 ±0.1 (0.04 ±0.004) 3 2.54 10.16 10.16 (0.40) (0.40) (0.