***ATTENTION*** PLEASE REMOVE THE RIGHT SIDE BAFFLE FILTER TO LOCATE YOUR NEW REMOTE CONTROL.
Revised 6/11/18 Copyright © 2018 Trade-Wind Manufacturing, LLC Proverbs 22:29 Page 2
INSTALLATION INSTRUCTIONS & USE & CARE GUIDE Trade-Wind® P3200 Series Range Hoods P3200 Series Model Width(in.) CFM 30‖ 36‖ 42‖ 30‖ 36‖ 42‖ 48‖ 390 390 390 600 600 600 780 P32303RC P32363RC P32423RC P32306RC P32366RC P32426RC P32487RC CONTENTS: Part 1 - Planning the Installation Part 2 - Electrical Connection Part 3 - Direction of Vent and Securing The Hood Part 4 - Use & Care Before beginning installation, please thoroughly read and become familiar with these instructions.
WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b) Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’). c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. d) Use proper pan size.
CAUTION –To reduce the risk of fire and to properly exhaust air, be sure to duct air outside – Do not vent exhaust air into spaces with in walls or ceilings or into attics, crawl spaces, or garages. CAUTION – To reduce the risk of fire and electric shock, install this range hood only with Integral Blower manufactured by Trade-Wind®. PART 1 Planning the Installation CAUTION: 1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 2.
WARNING! Following Are Manufacturer’s Suggestions. Always Observe Local Building Codes. Hoods installed in custom canopies constructed of combustible materials should be installed with the combustible material structure a minimum of 36‖ above the cooking surface. Hoods installed in custom canopies constructed of non-combustible materials, should be installed with the non-combustible material structure a minimum of 30‖ above the cooking surface.
NOTE: DRILLING THROUGH STAINLESS STEEL REQUIRES TITANIUM DRILL BITS. BE CAREFUL NOT TO DRILL THROUGH THE UL LABEL OR INTO THE HOOD’S ELECTRICAL COMPONENTS. PART 4 Use and Care FILTER REMOVAL Each filter has two aluminum cylindrical knobs, one towards the rear and one towards the front. The front knob is actually a screw that holds the filter in place. The rear knob is only for grasping and is permanently connected to the filter.
Explaining the Remote The diagram to the left shows all functions of the remote. Push the speed or light buttons once to turn on; push the same button a second time to turn off. You can use the ―off‖ button to power off the lights and blower simultaneously. The ―5 minute delay auto off‖ button can be pressed when the blower is on at any speed. The blue light behind the speed button will blink showing that this feature has been activated.
WARRANTY Kitchen Ventilation Products What IS Covered: ® ® Trade-Wind Manufacturing, LLC warrants its Trade-Wind Kitchen Ventilation Products to the original user, to be free of defects in materials and workmanship for three (3) years from the date of purchase. ® Trade-Wind Manufacturing, LLC at its option, will repair or replace the complete unit or any defective component without charge. This warranty may be voided if any unauthorized service, alterations, or repairs are made to the product.
Brands Best Practices Venting Installation Instructions for Range Hoods and Wood Hood Liners (All Models) —Addendum to Installation Instructions— IMPORTANT: Problems caused by improper installations are not covered by the manufacturer’s warranty. IMPORTANT: Undersized and improperly installed duct pipe and/or other ventilation components will cause excessive static pressure (air resistance), that may result in rattling, vibration and air buffeting noises, as well as inadequate ventilation. 1.
Duct Pipe and Fitting Sizes (Continued) Duct Runs – Length a. Configure the ventilation duct run to be as short and as direct to the outside as possible. Minimize the number of elbows and transition fittings used. Complex or long runs should be reviewed by a qualified installer. b. No portion of the ducting should be run so that the exhaust air flows downward. Since exhaust heat rises, forcing the air to flow downward will cause increased static pressure.
In-line dampers must be installed so that the exhaust air flow will open the butterfly blades. For horizontal duct runs, the in-line damper must be installed so that the hinge between the two butterfly blades is vertical—the hinge pin must point up and down. Otherwise, because of gravity, the damper’s blades will not close and the damper will not prevent backdrafts. For vertical duct runs, the in-line damper’s hinge will be horizontal (sideways), which is correct for vertical duct runs.
