WORK TABLE & BACK BOARD ASSEMBLY INSTRUCTIONS 21 Staffern Drive Concord, ON L4K 2X2 www.trademarktools.
CONTENTS OF THE WORK TABLE & BACKBOARD CARTON A B C D A. Bottom board (1198 x 598 x 6 mm) B. Table-top board (1198 x 598 x 15 mm) C. Holed back board (1200 x 217 x 6 mm) D. Peg board (1188 x 607 x 4.5 mm) 1 2 3 4 1. Bolt M6 x 15 mm (8pcs) 2. Bolt M6 x 10 mm (63pcs) 3. Nut M6 (71pcs) 4. Washer M6 (71pcs) 5. Wood Screw (4pcs) 6. Bolt M x 10 mm (8pcs) (for handle) 7. Bolt M4 x 12 mm (10pcs) 8. Nut (18pcs) 9. Washer M4 x 14 mm (18pcs) 10. Drawer Handle (2pcs) 11. Reinforced metal plate (1pc) 12.
CONTENTS OF THE WORK TABLE & BACKBOARD CARTON (cont.) 13. Top rail 1198 mm (2pcs) 14A. Cross member 1186 mm (3pcs) 14B. Cross member (with holes in centre) 1186 mm (2pcs) 15. Left holed back board support 640 mm (1pc) 16. Right holed back board support 640 mm (1pc) 17. Left top cantilever arm 215 mm (1pc) 18. Right top cantilever arm 215 mm (1pc) 19. Side rail 586 mm (4pcs) 20. Left rear leg 996 mm (1pc) 21. Right rear leg 996 mm (1pc) 22. Left front leg 900 mm (1pc) 23. Right front leg 900 mm (1pc) 24.
TOOL BOARD ASSEMBLY STEP 1 Place the left holed back board support (15) and the right holed back board support (16) on a level surface. 14B STEP 2 Mount a cross member (13) between the holed back board supports. Fasten the corners using bolts, washers and nuts provided. STEP 3 Place the holed back board (D) in between the frames (as shown). Use two M6 x 15 mm bolts (type 1), washers and nuts at the top to fasten the holed back board (D) to the frame.
DRAWER ASSEMBLY STEP 1 Attach the drawer handles (10) to the drawer front panel (30) using the bolts, washers and nuts (type 7). STEP 2 Assemble the drawer unit as shown below, and use bolts and nuts to fasten the corners.
WORK STATION ASSEMBLY STEP 1 Place left rear leg (20) and right rear leg (21) on a level surface. STEP 2 Connect the two rear legs, at the bottom, with a cross member (14A). STEP 3 Mount another cross member (14B) at the top of the legs.
WORK STATION ASSEMBLY (cont.) STEP 4 Place the four side rails (19) on the rear legs. STEP 5 Mount the left guide rail (24) and the right guide rail (25) on the rear legs, at the top, as shown. STEP 6 Place the left front leg (22) and the right front leg (23) on the side rails.
WORK STATION ASSEMBLY (cont.) STEP 7 Mount a cross member (14A) between the front legs (on the upper frame) and secure with bolts and nuts. STEP 8 Mount a second cross member (14A) between the front legs (on the lower frame) and secure with bolts and nuts. Place the feet plastic protectors (12) on the base of each foot. STEP 9 Place the work station in the upright position.
WORK STATION ASSEMBLY (cont.) STEP 10 Slide the assembled drawer into place along the guide rails (24) and (25). STEP 11 Place the bottom board (A) on the lower part of the work station (as shown). STEP 12 Place the table top board (B) on the top section of the work station.
WORK STATION ASSEMBLY (cont.) STEP 13 Mount the assembled Tool Board on the table and securely fasten using M6 x 15 mm bolts (type 1) through the openings in the holed board. STEP 14 Fix the reinforced metal plate (11) onto the back lower part of the assembled Table Top Board and secure tightly with the bolts, washers and nuts provided.
