ltNbo’S MANrAi BBnmId obSIabNTIAi mbiibT doIii This drill mrotected rnder matent NumbersW PTMIUOP and QIUOPISUQ clo lrTallo rSb lNiY! tAoNINd! al NlT STlob lo rSb ClMBrSTIBib MATboIAiS NbAo TeIS AmmiIANCb! rSb lNiY ToAbdbo BoANa eAoatlla BBn mbiibTS IN Teb lmboATIlN lc TeIS rNIT.
fkTolarCTflk `ongratulations on your purchase of this qraeger tood mellet drillI jodel BBnmfdK tith proper setJupI operationI and maintenanceI the drill will provide you with delicious food and years of cooking enjoymentK klTbW krMBbop cliiltfkd mAoT kAMbp obcbo Tl Teb ClMmlkbkT afAdoAM clrka kbAo Teb bka lc Tefp MAkrAiK After removing the box from the drillI remove all parts from inside the drillK oemove any remaining packaging material from inside the drill as wellK jake sure you haveI and can identify al
pbCTflk lkbW AppbMBiv fkpTorCTflkp obMlsfkd Teb pefmmfkd BoAChbTpW oemove the four phipping Brackets securing the drill to the pallet using your NLQ” socket L driver or wrenchK fkpTAiifkd Teb CApTbopW qhis process will be much easier and safer if you have another person to helpK `arefully lay the drill on its back on a nonJabrasive surfaceK fnstall the four `asters by following the diagram belowW qhe iocking `asters EUOF are to be located on the front of the drill Eaoor pideFK cirmly seat each `aster min in
klTbW ff at this point you are ready to start your drillI refer to the fkfTfAi cfofkd fkpTorCTflkp in pbCTflk Ttl of this manual or on a separate sheet in the mbiibT elmmbo before proceeding with further assemblyK tAokfkd! Many parts of the drill will become very hot during operationK Care must be taken to avoid burnsI both during operation and afterwardsI while the drill is still hotK ft should never be left unattended when young children are presentK Never move the drill when it is operatingK iet it thor
pbCTflk TtlW fkfTfAi cfofkd fkpTorCTflkp (To be used on initial firing or anytime the drill runs out of mellets) fn order to ensure proper operation of the drillI you must first allow the Auger Tube to be “charged” with melletsK NF lpen the aoorLiid and remove the morcelain drillI drease arain man and eeat Baffle from inside the drillK OF jake sure the pwitchLaial is in the lcc positionK mlug the mower `ord into an appropriateI grounded electrical outletK PF lpen the mellet eopper iid and locate the AugerK
pbCTflk TeobbW prBpbnrbkT pTAoTJrm tith the aoor openI turn the pwitchLaial lk and qemperature aial to pjlhbK fn approximately O minutes you will notice whitishJgray smoke coming out of the drill as the mellets igniteK After assuring the mellets have ignitedI close the aoor and set the qemperature aial to any cooking setting desiredK ff the drill fails to light or if the fire in the cirepot goes out while cooking or smokingI follow these stepsW NF qurn the pwitchLaial to lccK lpen the aoor and remove all fo
pbCTflk clroW lmboATfkd Tfmp NF qhe qemperature aial can be changed at any time to increase or decrease the cooking temperature of the drillK qhe efdeLefdebo qemperature settings are for drillingK qhe jbaLjfa oAkdb qemperature settings are for plow `ookingK qhe pjlhb setting is for pmoking and adding pmoke clavor to foods being cookedK qhe pjlhb setting can also be used to “hold” foods at approximately NUM to OMM degrees cK OF vour qoAbdbo mbiibq dofii should never be moved while it is hotK ff you are trans
PF ff the drill is stored outside during the rainy seasonI care should be taken to ensure that water does not get into the mellet eopperK tood pelletsI when wetI expand greatly and will jam your AugerK A ToAbdbo dofii Clsbo to protect the drill is highly recommended! Covers are available from your Traeger aealerI or log on to our teb pite – wwwKtraegergrillsKcomK QF aepending on useI periodically remove the morcelain drillI drease arain man and eeat Baffle to clean the ash from in and around the cirepotK A
ptill no mellets in the cirepot – mroceed to step PK PF aisconnect mower `ord from electrical outletK aF rnplug the Auger arive jotor E oedLthite wire pair connectorF and the araft fnducer can ElrangeLthite wire pair connectorFK bF oeconnect the araft fnducer can to the oedLthite wire pair and the Auger arive jotor to the lrangeLthite pairK cF mlug mower `ord into an appropriateI grounded electrical outlet and turn the pwitchLaial lkK dF ff the Auger arive jotor is operating Echeck the small fan blade on th
tev albp Mv dofii cfob dl lrT lk “pMlhb” pbTTfkd? bxcess ash in the cirepot may be the problemK NF lpen the aoor and remove the morcelain drillI drease arain man and eeat Baffle from inside the drillK OF fMmloTAkTW oemove all unburned mellets and ash from inside and around the cirepotK A shopJvac is ideal tor this task CArTflk! Approb TeAT Teb dofii fp Clia Tl Aslfa A cfob colM elT ApeK PF oeplace the eeat BaffleI drease arain man and the morcelain drill and initiate startJ up procedureK QF ff this didn’t r
pbCTflk pbsbkW ToAbdbo prmmloT marts are identified by number on the following `ljmlkbkq afAdoAj mAdbK qo order partsW `allI bJmail or write to your qraeger aealer or qraeger mellet drillsK mlease provide your nameI phone numberI addressI jodel and perial kumber of the drill Elocated on a label inside the eopper iidFI along with the part identification number from the `omponent aiagramK ToAbdbo mbiibT dofiipI iiCK VQQR pt oidder ooad @PNM tilsonvilleI lo VTMTM ToAbdbo TbCekfCAi prmmloT Available T aays a t
