OWNERS MANUAL OUTDOOR FIRE PIT OFP001 FOR OUTDOOR USE ONLY! Please read this entire manual before assembly, installation of your Traeger Pellet Outdoor Fire Pit. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact your local building or fire official about restrictions and installation inspection requirements in your area.
A MAJOR CAUSE OF FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARENCES (AIR SPACES) TO COMBUSTIBLES MATERIALS. IT IS OF UTMOST IMPORTANCE THAT THIS PRODUCT BE INSTALLED ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS. DANGER! This product is designed for outdoor use only. DANGER! Do not use on wooden decks. DANGER! Fire Pit is meant to burn wood pellets only and split logs. WARNING! Not for use by children. Danger! The Fire Pit is hot when in use. Use caution and never touch a hot Fire Pit with bare hands.
INTRODUCTION Congratulations on your purchase of this Traeger Outdoor Fire Pit, Model OFP001. With proper set-up, operation and maintenance, the Fire Pit will provide you with years of enjoyment. NOTE: NUMBERS FOLLOWING PART NAMES REFER TO THE COMPONENT DIAGRAM FOUND NEAR THE END OF THIS MANUAL. When you un-box the Fire Pit, remove all parts from the box and inside the Fire Pit. Remove any remaining packaging material from inside the Fire Pit as well.
SECTION ONE: ASSEMBLY INSTRUCTIONS MOUNTING THE FIRE PIT FOOT TO THE FIRE PIT BASE: 1. Insert foot assembly (3) onto Fire Pit Base Assembly (1) with the tab on the Foot Assembly facing in and align with holes in base. 2. Secure using 2 each 1/4-20 Hex Bolt (7) and 1/4 Flat Washer (8) and tighten with wrench. MOUNTING THE FIRE PIT PELLET PAN ASSEMBLY TO FIRE PIT BASE: 1. Insert Fire Pit Pellet Pan Assembly (2) into The Fire Pit Base Assembly aligning the cutouts in the pan to the brackets in the base.
MOUNTING THE ASH PAN TO FIRE PIT BASE: 1. Insert the Ash Pan (6) onto the underneath side of the Fire Pit Base Assembly (1) and turn until the notches in the pan align with the tabs on the Foot. Insert the Ash Pan above the clips and rotate 60 degrees so it will not fall out. MOUNTING THE PORCELAIN GRILL TO FIRE PIT BASE: 1. The OFP001 has 2 grill positions that can be used.
MOUNTING THE FIRE PIT LID ASSEMBLY TO FIRE PIT BASE: Place the lid Assembly (4) onto the Fire Pit so the flange is centered on Fire Pit.
FIRE PIT COMPONENTS OFP001 Item 1 2 3 4 5 6 7 8 9 Qty 1 1 3 1 1 1 6 6 1 Description Fire Pit Base Assembly Fire Pit Pellet Pan Assembly Fire Pit Foot Assembly Fire Pit Lid Assembly Porcelain Grill Ash Pan Round 1/4-20 x .
SECTION TWO: FIRE PIT START-UP 1. Remove the Fire Pit lid and Porcelain Grill and set aside. 2. Pour pellets into the Pellet Pan Assembly and mound up as shown in Figure 1. 3. Apply Lighter fuel in a circular ring approximately half way down the pellet mound. 4. Light the fuel on fire and then place the Porcelain grill and the lid back onto the Fire Pit. Figure 1 FIRE PIT PELLET REFILLING The Fire Pit is hot, always use the Poker to remove the Fire Pit lid and the Porcelain Grill.
SECTION SEVEN: TRAEGER SUPPORT Parts are identified by number on the following COMPONENT DIAGRAM PAGE. To order parts: Call, E-mail or write to your Traeger Dealer or Traeger Pellet Grills. Please provide your name, phone number, address, Model and Serial Number of the Grill (located on a label inside the Hopper Lid), along with the part identification number from the Component Diagram.