5X OPERATING MANUAL
OPERATING MANUAL WARNING Carefully read and understand all the instructions before connecting your new 5X. Failure to follow these guidelines may result in serious injury to persons and property for which Trailer Valet will not be held liable. Do not allow persons to operate or assemble this unit until they have read this manual and have developed a thorough understanding of how the unit works. TABLE OF CONTENTS WARNING AND TABLE OF CONTENTS.................................................................
IMPORTANT SAFETY INFORMATION Failure to heed these markings may result in personal injury and/or property damage: 1. DO NOT use the 5X on slopes and inclines beyond stated limits. 2. DO NOT submerge the 5X in water (salt or fresh) or leave it in water for prolonged periods, since this can damage the gears and erode lubricants. 3. DO NOT use your drill on the 5X’s high gear. (Attachment sold separately) 4. Carefully read all instructions.
SPECIFICATIONS The Trailer Valet 5X is made of high strength steel and given a powder coat finish made to resist corrosion from the elements and marine use. When cared for properly, it will provide years of service. The 5X mounts to the side of trailer tongue. Once mounted to your trailer, the 5X makes maneuvering your trailer much easier than your old jack. Hitching and unhitching, leveling, and moving is now done with precision. The 5X is designed for trailers up to 5,000 lbs.
WHAT’S IN THE BOX Upon removing items from packaging, it is very important to thoroughly inspect all parts of the system before using the device. Any part that is missing or damaged must be immediately replaced. Contact Trailer Valet Customer Service at 1-844-846-9344 or Support@TrailerValet.com A. The Trailer Valet 5X 1. Axle Yoke Compartment 2. Jack/Jack Tube 3. Jack Crank 4. Brake Cap 5. Steering/Brake Handle 6. Side Plates 7. Gear Covers 8. Low Gear Driveshaft 9. High Gear Driveshaft 10.
ASSEMBLY STEP 1: SET UP When installing the Trailer Valet 5X, the unit must be installed while the weight of the trailer is supported by an existing jack. Having wheel chocks in place during connection will insure a safe install. Raise the trailer tongue to where the coupler is about 16 inches off the ground to give adequate space to attach the dolly. During installation, the Steering Handle must be secured to the safety clip to ensure the brake is engaged at all times.
OPERATING INSTRUCTIONS Knowing the proper techniques to operate your 5X can help keep you and others around you safe. In this guide, you are shown the basic fundamentals for effective operations. However, it is up to you to analyze the situation and make the decisions necessary for the proper use of your 5X. Apply your knowledge of your 5X and the basic fundamentals you have practiced to adjust your techniques to each unique situation.
OPERATING INSTRUCTIONS Slot the Drill Adapter in your Drill chuck and secure tightly to avoid the adapter slipping. Align and insert the Drill Adapter to the low gear Driveshaft. Use of an electric drill is not recommended on the high gear. Hold the drill firmly when engaging. If using an electric drill, it will have high initial torque if the drill trigger is pulled rather than squeezed.
OPERATING INSTRUCTIONS STEP 7: STORING THE DEVICE 1. Remove the drill/drive handle. 2. Lower your trailer’s existing jack until the Trailer Valet is above the ground. Restore the clevis/stow and rotation pins while the unit remains attached to the mounting bracket. This will allow the 5X to remain attached to the trailer while being towed. 3. Insert the rotation pin into the jack assembly. 4.
MAINTENANCE CHECK BEFORE BEFORE FIRST USE EACH USE EVERY 90 DAYS Take the time to read and understand these operating instructions in order to understand your 5X and its operations. Read and understand your drill/driver operator’s manual and instructions. Inspect the 5X for damage. Replace any damaged parts immediately. If a part must be replaced, contact Trailer Valet Customer Service 844-846-9344.
LIMITED MANUFACTURER’S WARRANTY SuperTech S Corp warrants for one year from the purchase date that the product will be in working condition and will be free from manufacturing defects, provided that installation and use of the product is in accordance with product instructions. This warranty is only made to the original consumer purchaser and is non-transferable. ALL OTHER WARRANTIES IMPLIED OR EXPRESSED ARE HEREBY DISCLAIMED. THIS WARRANTY DOES NOT COVER: 1.
Copyright 2022 by Supertech S. Corporation. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Supertech S. Corporation. For further information or if you have any questions, please contact: SUPERTECH S. CORP. Customer Service: (844) 846-9344 Email: support@trailervalet.com W W W.TRAILERVALET.