TCONT600AF11MA / TCONT602AF22MA Programmable Comfort Control OWNER’S GUIDE
Quick Reference Card Battery Holder Grasp and pull to see basic operating instructions at a glance. Press down and pull to remove batteries. Batteries should be replaced once a year (see page 17). CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C). Need Help? For assistance with this product please visit www.trane.com or call the Customer Assistance Helpline toll-free at 1-800-500-2041.
Table of contents About your new Comfort Control Control features ..............................2 Programming at a glance ................3 Quick reference to controls............4 Quick reference to display..............5 Appendices Battery installation ........................17 In case of difficulty ......................18 Customer assistance......................20 Accessories/replacement parts ....20 Limited warranty ..........................21 Programming & Operation Set time and day..............
About your new Comfort Control Congratulations on the purchase of your new Comfort Control. It has been designed to give you many years of reliable service and easy-to-use, push-button climate control. Features • • • • • • • Separately programmable weekday/weekend schedules. One-touch temp control overrides program schedule at any time. Energy Star® compliant to greatly reduce your heating/cooling expenses. Large, clear, backlit display is easy to read — even in the dark.
This Comfort Control is ready to go! Your new Comfort Control is pre-programmed and ready to go.All you have to do is set the time and day. Then check the settings below and change if needed: 1 Set time and day (required for proper operation)................................See page 6 2 Select fan setting (Auto/On): Preset to Auto ......................To change, see page 7 3 Select system setting (Heat/Cool): Preset to Heat ..............
Quick reference to controls Digital display (see page 5) Battery holder (see page 17) Temperature buttons Press to adjust temperature settings (see page 11-13) Hold button Press to override programmed temperature control (see page 13) Function buttons Press to select the function displayed just above each button. (Functions change depending on the task.
Quick reference to display screen Current inside temperature Low battery warning (see page 17) Current time/day (see page 6) In Recovery (see page 16) Temperature setting (see pages 11-13) In Recovery Current program period Wake/Leave/Return/Sleep (see pages 9-11) Auxillary Heat On Auxiliary heat (Only for heat pumps with auxiliary heat) System status Heat On/Cool On (If flashing, see page 15) Set Clock/Day/Schedule (see pages 6 & 11) Function buttons Press the button beneath each function to view o
Set the time and day Press SET CLOCK/DAY/SCHEDULE, Press SET DAY, then adjust time then select current day Wed Done Set Day Set Schedule 1 Press the SET CLOCK/DAY/SCHEDULE button, then press or to set the clock time. 2 Press the SET DAY button, then press or to select the day of the week. 3 Press DONE to save & exit. Note: If the SET CLOCK/DAY/SCHEDULE option is not displayed, press DONE or RUN SCHEDULE.
Select the fan setting Press the FAN button to select Auto or On. Heat On Heat In “Auto” mode (the most commonly used setting), the fan runs only when the heating or cooling system is on. If set to “On,” the fan runs continuously. Use this setting for improved air circulation, or for more efficient air cleaning.
Select the system setting Press the SYSTEM button to select: Heat • • • • Cool • Heat: Controls only the heating system. Cool: Controls only the cooling system. Off: Heating and cooling systems are off. Auto: Automatically selects heating or cooling depending on the indoor temperature. Em Heat (only for heat pumps with auxiliary heat): Controls Emergency Heat. Compressor is locked out. Note: The Auto and Em Heat system settings may not appear, depending on how your Comfort Control was installed.
Save money by setting program schedules It’s easy to program your system for maximum energy savings.You can program four time periods each day, with different settings for weekdays and weekends. WAKE 8:00 am LEAVE 8:00 am Set to the time you awaken and the temperature you want during the morning, until you leave for the day. Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level).
Energy Star® settings for maximum cost savings This Comfort Control is pre-set to use Energy Star® program settings.We recommend these settings, since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each time period.
To adjust program schedules Cool Done Set Day Set Schedule Heat Set Schedule AM Leave Done Mon Tue Wed Thu Fri CancelPeriod Next 1 Press SET CLOCK/DAY/SCHEDULE, then SET SCHEDULE. 2 Press or to set your weekday Wake time (Mon-Fri), then press NEXT. 3 Press or to set the temperature for this time period, then press NEXT. 4 Set time and temperature for the next time period (Leave). Repeat steps 2 and 3 for each weekday time period.
Program schedule override (temporary) Press to temporarily adjust temperature Temporary Run Schedule Press to cancel temporary setting and resume program schedule Note: Make sure the Comfort Control is set to the system you want to control (heat, cool or auto). Press or to immediately adjust the temperature.This will temporarily override the temperature setting for the current time period. The new temperature will be maintained only until the next programmed time period begins (see page 10).
Program schedule override (permanent) Press to permanently adjust temperature Hold Run Schedule Press to cancel “Hold” setting and resume program schedule Note: Make sure the Comfort Control is set to the system you want to control (heat, cool or auto). Press HOLD to permanently adjust the temperature.This will override the temperature settings for all time periods. The “Hold” feature turns off the program schedule and allows you to adjust the Comfort Control manually, as needed.
Auto Changeover (heat/cool) Auto Changeover is a feature used in climates where both air conditioning and heating are used on the same day.When the system is set to Auto, the Comfort Control automatically selects heating or cooling depending on the indoor temperature. Press until screen displays “Auto” Note: The Auto system setting may not appear, depending on how your Comfort Control was installed. Heat and cool settings must be at least 3 degrees apart.
Built-in compressor protection This feature helps prevent damage to the compressor in your air conditioning or heat pump system. Set Clock/Day/ Schedule Message flashes until safe restart time has elapsed Damage can occur if the compressor is re-started too soon after shutdown.This feature forces the compressor to wait for a few minutes before restarting. During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump).
Adaptive Intelligent Recovery™ (AIR) Adaptive Intelligent Recovery eliminates guesswork when setting your schedule. It allows the Comfort Control to “learn” how long your furnace and air conditioner take to reach the temperature you want. Just set your program schedule to the time you want the house to reach your desired temperature.The Comfort Control then turns on the heating or cooling at just the right time to reach your scheduled temperature at your scheduled time.
Battery replacement Press and pull to remove Replace Battery Insert fresh AA alkaline batteries, then reinstall battery holder Batteries are optional (to provide backup power) because your Comfort Control was wired to run on AC power when installed. Install fresh batteries immediately when the REPLACE BATTERY warning begins flashing.The warning flashes about two months before the batteries are depleted.
In case of difficulty If you have difficulty with your Comfort Control, please try the suggestions below. Most problems can be corrected quickly and easily. Display is blank • • • Temperature settings do not change Make sure heating and cooling temperatures are set to acceptable ranges: • Heat: 40° to 90°F (4.5° to 32°C). • Cool: 60° to 99°F (10° to 37°C).
In case of difficulty Heating or cooling system does not respond “Cool On” or “Heat On” is flashing • Press SYSTEM button to set system to Heat. Make sure the temperature is set higher than the Inside temperature. • Press SYSTEM button to set system to Cool. Make sure the temperature is set lower than the Inside temperature. • Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is on. • Make sure furnace door is closed securely.
Customer assistance For assistance with this product, call your HVAC Contractor or visit www.trane.com. Or call the Customer Assistance Helpline toll-free at 1-800-500-2041. Model number xxxxxxx Date code xxxxxxx To save time, please remove the battery holder and note your model number and date code before calling. Accessories/replacement parts Battery holder ..............................Part No. THT02506 Cover plate assembly ........Part No. BAYCOVR700A (Use to cover marks left by old thermostats.
Limited 5-year warranty Low Voltage Room Comfort Controls This limited warranty is extended by Trane, to the original purchaser and to any succeeding owner of the real property to which the Comfort Control is originally affixed, and applies to products purchased and retained for use within the U.S.A. and Canada. If any part of your Comfort Control fails because of a manufacturing defect within five years from the date of the original purchase,Warrantor will furnish without charge a new Comfort Control.
Limited 5-year warranty THE LIMITED WARRANTY AND LIABILITY SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES AND LIABILITIES,WHETHER IN CONTRACT OR IN NEGLIGENCE, EXPRESS OR IMPLIED, IN LAW OR IN FACT, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR USE, AND IN NO EVENT SHALL WARRANTOR BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Limited 5-year warranty Parts will be provided by our factory organization through an authorized service organization in your area listed in the yellow pages.
6200 Troup Highway Tyler, TX 75711-9010 www.trane.com ® U.S. Registered Trademark • Patents Pending. © 2005 American Standard All rights reserved Pub. No.