Thermostat User Manual

ManualsBrandsTrane ManualsThermostatTZEMT400BB32MAA

Thermostat

Model TZEMT400BB32MAA

Installation, System Setup, and

Enrollment Instructions

Customer Service: (877) 288-7707

WARNING

Voltage hazard. Can cause electrical shock or equipment damage. Disconnect power to heating and cooling

equipment before beginning installation.

Remove the existing thermostat cover from the wall plate. Leave

wires attached.

Consult instructions that came with existing thermostat as needed.

Wall plate

Thermostat cover

The look of your existing

thermostat may vary

Physical Installation and Wiring

The Trane Thermostat is compatible with single and multistage forced air

systems, including:

• Gas furnace systems

• Oil furnace systems

• Electric furnace systems

• Heat pump systems

• Air conditioning systems

The Trane Thermostat may be compatible with some other system

types, including:

• Boiler systems

• Geothermal systems

• Multi-zoned systems

Call (877) 288-7707 to verify compatibility.

The Trane Thermostat is not compatible with the following system types:

• Radiant ﬂoor systems

• Wall heating systems

Also, the Trane Thermostat is not compatible with dual fuel systems

(gas furnace & heat pump combined) without adding a special kit. See

Note below.

• Note about dual fuel systems: This thermostat is not compatible

with dual fuel systems (heating system with both heat pump

and gas furnace), unless the system is controlled with a dual

fuel accessory relay kit. If you are unsure whether your dual fuel

system is controlled with this accessory or if you need a dual

fuel kit, please contact a qualiﬁed heating and cooling contractor.

Tools Needed

1/8”

Bridge requires one 9-Volt battery for

enrollment process. Battery not included.

For professional installation service, instructions, operation guide, and installation video modules, please visit link.schlage.com

Customer Service hours of operation:

•Monday-Friday9.00am-7:00pmEST

•Saturday11:00am-6:00pmEST

•Sunday11:00am-4:00pmEST

To use the remote features of this thermostat, a Schlage LiNK

account is required. Schlage LiNK™ online setup requires

broadband internet service and router with available port.

Summary of content (12 pages)

PAGE 1
Thermostat Model TZEMT400BB32MAA Installation, System Setup, and Enrollment Instructions To use the remote features of this thermostat, a Schlage LiNKTM account is required. Schlage LiNK™ online setup requires broadband internet service and router with available port. For professional installation service, instructions, operation guide, and installation video modules, please visit link.schlage.com Customer Service: (877) 288-7707 Customer Service hours of operation: • Monday-Friday 9.
PAGE 2
3 Determine if your system has a 24 VAC common wire which is required to power the thermostat. • If your system is a heat pump, skip to step 4. a. If your existing thermostat has a terminal named C, COM, X, or B with a wire connected to it, skip to step 4. b. If your thermostat does not have that terminal, or does not have a wire connected to it, go to step 3a. 3A Connect a 24 VAC common wire to power the thermostat. a.
PAGE 3
Label the wires on your existing thermostat to match terminal names. B B E F G O L Y1 Y2 Rc Rh X2 R R T W1 W2 W3 W X2 Rh Rc R R 5 Rc R C C X Y P516-001 Rev. 03/09-a If your thermostat has any terminals with names that do not match any on the label, write down the terminal names and wire colors for later reference. T • Wire colors and letters may vary W3 W2 W1 W If you have a W terminal, use the W1/W label on that wire.
PAGE 4
6 Identify your System Type from the list below. You will need to check your wire labels to help identify the system type.
PAGE 5
7 Separate the face of the new thermostat from the wall plate. Tabs Apply pressure at two tabs on top of wall plate to release it. • NOTE: It is not recommended that this Z-wave thermostat be mounted onto metal structures. Metal may affect the radio frequency (RF) communication between the thermostat and the Z-wave signal to the Schlage Bridge. 24R C G Y1 Y2 RS 2 RS 2 HC 24C 24R H W1 W2/ O RS 1 RS 1 H1 Wall plate 8 Mark two mounting holes using new wall plate. a. b. c. d. e.
PAGE 6
11 Review the wiring table information. a. Refer to: • Table 1 - If you do NOT have a heat pump • Table 2 - If you have a heat pump b. Select the correct row based upon the thermostat being replaced, and then circle the wire labels you have. c. Connect your wires as shown in the New Thermostat Terminals row.
PAGE 7
13 If necessary, cut the internal jumper wire (JP1). If only one wire is connected to either 24RC or 24RH as shown Do NOT cut JP1 jumper If wires are connected to both 24RC and 24RH as shown Cut JP1 jumper RC 24RC 1 JP C 4R 24RH 24RC W1 24RH OR 24RC 24RH 2 RC G Y1 4C 2 RH RH 2 RS W1 RS /O W2 1 RS W1 Y2 24 2 LD SH C HI- 1 RS LD SH NO HI- RH W1 Cutting the JP1 jumper The jumper is located on back of the thermostat face as shown in the illustration to the right.
PAGE 8
System Settings at Thermostat 16 Set Time and Date c. Scroll up or down to Set Clock (it is the first option), then press the Select button. a. Press the MENU button twice. Scroll up User Settings 11:15 PM 68 H 78 MENU MODE Set Clock Filter Service Maint Service Screen Timeout 78 C FAN RUN Select Done MENU button Select button b. Scroll up or down to User Settings (it is the first option), then press the Select button.
PAGE 9
18A Gas Furnace - Multistage Mechanical Settings a. Press the MENU button twice. b. Press and hold the two inner buttons for 3 seconds to view Installer Settings. c. Scroll down to System Settings and press the Select button. d. Scroll to Mechanical Settings (it is the first option), then press the Select button. e. Scroll down to 2nd Stage Heat. f. Press the + button to change the setting to Y for Yes. g.
PAGE 10
Perform System Checkout 19 Test Fan Operation a. b. c. d. e. f. Press the FAN button. Scroll to ON. Verify that the system fan starts and moves air. Press the FAN button. Scroll to AUTO. Press the Done button to return to the home screen. 11:15 PM Sys Off Run 75 AUTO AUTO MENU MODE FAN 76 H 74 C RUN Test Cooling Operation (if your system has cooling) Press the MODE button. Scroll to COOLING. Press the Done button to return to the home screen.
PAGE 11
Enroll Thermostat into existing Schlage LiNKTM System 20 Prepare the Schlage Bridge for enrollment. • If you are using a controller that is not a Schlage Bridge, consult the instructions that came with the controller to find out how to enroll a new device. Blue light a. Unplug Ethernet and power cables from Schlage Bridge. b. Install a quality 9 volt battery. c. Verify that blue light is blinking. If blue light is solid, battery is dead. Replace with new 9 volt battery, if needed. d.
PAGE 12
23 Establish Online Control of the Thermostat. A Schlage LiNK account is required to complete the setup. If you have an active Schlage LiNK account, continue with the steps below. If you need to create a new account, go to www.schlagelink.com and click on “Just Purchased A Schlage LiNK System?” For more information about the Schlage LiNK system, visit www.link.schlage.com. Completing the setup. a. Remove the battery from the Schlage Bridge. b. Plug the Ethernet and power cord back into the Schlage Bridge.