TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Description Features Transcend High Capacity SD Card series are • RoHS compliant product. specifically designed to meet the High Capacity, High • Card Lid material: PC (comply with UL94,Flame Class:HB) Definition Audio and Video requirement for the latest • Operating Voltage: 2.7 ~ 3.6V Digital Cameras, DV Recorders, Mobile Phones, etc,.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Architecture Transcend Information Inc.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Bus Operating Conditions • General Parameter Symbol Min. Max. Unit -0.3 VDD+0.3 V -10 10 µA -10 10 µA Symbol Min. Max. Unit Supply voltage VDD 2.7 3.6 V Output High Voltage VOH 0.75* VDD Output Low Voltage VOL Input High Voltage VIH Input Low Voltage VIL Peak voltage on all lines Remark All Inputs Input Leakage Current All Outputs Output Leakage Current • Power Supply Voltage Parameter 0.125* VDD 0.625* VDD VDD+0.3 VSS-0.
TS4G-32GSDHC6-P2 Single card capacitance SDHC Memory Card + Reader P2 CCARD Maximum signal line inductance Pull-up resistance inside card (pin1) RDAT3 10 10 pF 16 nH fPP ≤ 20 MHz 90 kΩ May be used for card detection Note that the total capacitance of CMD and DAT lines will be consist of CHOST, CBUS and one CCARD only because they are connected separately to the SD Memory Card host.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • Bus Signal Levels As the bus can be supplied with a variable supply voltage, all signal levels are related to the supply voltage. To meet the requirements of the JEDEC specification JESD8-1A and JESD8-7, the card input and output voltages shall be within the following specified ranges for any VDD of the allowed voltage range: Symbol Min. Output HIGH voltage Parameter VOH 0.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • Bus Timing Parameter Symbol Min Max.
TS4G-32GSDHC6-P2 Output Delay time during Data Transfer Mode SDHC Memory Card + Reader P2 tODLY 0 14 ns CL ≤ 40 pF, (1 card) Output Delay time during Identification Mode tODLY 0 50 ns CL ≤ 40 pF, (1 card) (1) 0 Hz means to stop the clock. The given minimum frequency range is for cases were continues clock is required Transcend Information Inc.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • Bus Timing (High Speed Mode) Parameter Symbol Min Max.
TS4G-32GSDHC6-P2 Output Delay time during Data Transfer Mode Output Hold time SDHC Memory Card + Reader P2 tODLY tOH ns CL ≤ 40 pF, (1 card) ns CL ≤ 40 pF, (1 card) 40 pF (1 card) 2.5 1 Total System capacitance for each line CL 1) In order to satisfy severe timing, host shall drive only one card. Transcend Information Inc.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Reliability and Durability Temperature Operation: -25°C / 85°C Storage: -40°C (168h) / 85°C (500h) Junction temperature: max. 95°C Moisture and corrosion Operation: 25°C / 95% rel. humidity Storage: 40°C / 93% rel. hum./500h Salt Water Spray: 3% NaCl/35C; 24h acc. MIL STD Method 1009 Durability 10.000 mating cycles; test procedure: tbd. Bending 10N Torque 0.15N.m or +/-2.5 deg Drop test 1.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Register Information Within the card interface six registers are defined: OCR, CID, CSD, RCA, DSR and SCR. These can be accessed only by corresponding commands (see Chapter 4.7). The OCR, CID, CSD and SCR registers carry the card/content specific information, while the RCA and DSR registers are configuration registers storing actual configuration parameters. 1. OCR register The 32-bit operation conditions register stores the VDD voltage profile of the card.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 OCR Register Definition 1) This bit is valid only when the card power up status bit is set. 2) This bit is set to LOW if the card has not finished the power up routine. The supported voltage range is coded as shown in Table 5-1. A voltage range is not supported if the corresponding bit value is set to LOW. As long as the card is busy, the corresponding bit (31) is set to LOW. 2. CID Register The Card IDentification (CID) register is 128 bits wide.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • PRV The product revision is composed of two Binary Coded Decimal (BCD) digits, four bits each, representing an “n.m” revision number. The “n” is the most significant nibble and “m” is the least significant nibble. As an example, the PRV binary value field for product revision “6.2” will be: 0110 0010 • PSN The Serial Number is 32 bits of binary number.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 The CSD Register Fields (CSD Version 2.0) The following sections describe the CSD fields and the relevant data types. If not explicitly defined otherwise, all bit strings are interpreted as binary coded numbers starting with the left bit first. • CSD_STRUCTURE Field structures of the CSD register are different depend on the Physical Specification Version and Card Capacity. The CSD_STRUCTURE field in the CSD register indicates its structure version.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 CSD Register Structure • TAAC This field is fixed to 0Eh, which indicates 1 ms. The host should not use TAAC, NSAC, and R2W_FACTOR to calculate timeout and should uses fixed timeout values for read and write operations (See 4.6.2). • NSAC This field is fixed to 00h. NSAC should not be used to calculate time-out values. • TRAN_SPEED The following table defines the maximum data transfer rate per one data line - TRAN_SPEED: Transcend Information Inc.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Note that for current SD Memory Cards that field must be always 0_0110_010b (032h) which is equal to 25MHz - the mandatory maximum operating frequency of SD Memory Card. In High-Speed mode, that field must be always 0_1011_010b (05Ah) which is equal to 50MHz. And when the timing mode returns to the default by CMD6 or CMD0 command, its value will be 032h. • CCC The SD Memory Card command set is divided into subsets (command classes).
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 • C_SIZE This field is expanded to 22 bits and can indicate up to 2 TBytes (It is the same as the maximum memory space specified by a 32-bit block address.) This parameter is used to calculate the user data area capacity in the SD memory card (not include the protected area). The user data area capacity is calculated from C_SIZE as follows: memory capacity = (C_SIZE+1) * 512K byte As the maximum capacity of the Physical Layer Specification Version 2.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 This field is set to 0. Host should not use this field. • COPY Defines if the contents is original (= ‘0’) or has been copied (=’1’). The COPY bit for OTP and MTPdevices, sold to end consumers, is set to ‘1’ which identifies the card contents as a copy. The COPY bit is an one time programmable bit.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 4. RCA Register The writable 16-bit relative card address register carries the card address that is published by the card during the card identification. This address is used for the addressed host-card communication after the card identification procedure. The default value of the RCA register is 0x0000. The value0x0000 is reserved to set all cards into the Stand-by State with CMD7. 5.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 is 0x404. 6. SCR Register In addition to the CSD register there is another configuration register that named - SD CARD Configuration Register (SCR). SCR provides information on SD Memory Card's special features that were configured into the given card. The size of SCR register is 64 bit. This register shall be set in the factory by the SD Memory Card manufacturer. The following table describes the SCR register content.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Defines the data status after erase, whether it is ‘0’ or ‘1’ (the status is card vendor dependent). • SD_SECURITY Describes the security algorithm supported by the card. SD Supported Security Algorithm Note that it is mandatory for a regular writable SD Memory Card to support Security Protocol. For ROM (Read Only) and OTP (One Time Programmable) types of the SD Memory Card, the security feature is optional.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Mechanical Dimension Transcend Information Inc.
TS4G-32GSDHC6-P2 Transcend Information Inc.
TS4G-32GSDHC6-P2 Transcend Information Inc.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Description Placement TS-RDP2 is a USB2.0 Portable SD/MMC Card Reader. It is a small and thin device specifically designed for fast, easy data transfer and exchange using multiple types of Memory Cards. Features • Color: White • Fully Compliant with the Hi-Speed USB 2.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Pinouts Pin Identification Pin No. Pin Name Symbol Function 01 VUSB USB- USB differential signal: 02 USB- USB+ The pairs are used to transmit 03 USB+ 04 VSS Data/Address/Command VSS Ground VUSB USB Power Input Block Diagram Controller USB Port VUSB 3.3V/1.8V Voltage Regulator 12MHz Crystal VD33P VDD18 VDDHM Transcend Information, Inc.
TS4G-32GSDHC6-P2 SDHC Memory Card + Reader P2 Recommended Operating Conditions: SYMBOL PARAMETER MIN. TYP. MAX. UNITS VUSB Power Supply 4.5 5.0 5.5 V TOPR Operating Temperature 0 O 70 C DC Characteristics: SYMBOL PARAMETER MIN. TYP. MAX. UNITS VDDHM Input Voltage 3.0 3.3 3.6 V VIN Input Signal Voltage -0.3 VDDHM+0.3 V VOUT Output Voltage 3.0 3.3 3.6 V VDD18 Supply Voltage 1.62 1.8 1.98 V DC Electrical Characteristics of 3.3V I/O: SYMBOL PARAMETER MIN. TYP.