TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Features Description • CompactFlash Specification Version 3.0 Complaint The Transcend 128MB ~ 8GB CFI is an industrial • RoHS compliant products CompactFlash Card with Industrial Flash Memory • Single Power Supply: 5V or 3.3V assembled on a printed circuit board.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Transcend Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Block Diagram Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Pin Assignments and Pin Type Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for 3-state signals not to consume current. 2) The signal should be grounded by the host. 3) The signal should be tied to VCC by the host. 4) The mode is optional for CF+ Cards, but required for CompactFlash Storage Cards. 5) The -CSEL signal is ignored by the card in PC Card modes.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Signal Description Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Electrical Specification The following tables indicate all D.C. Characteristics for the CompactFlash Storage Card. Unless otherwise stated, conditions are: Vcc = 5V ±10% Vcc = 3.3V ± 5% Absolute Maximum Conditions Input Power Input Leakage Current Input Characteristics Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Output Drive Type Output Drive Characteristics Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Signal Interface Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Notes: 1) Control Signals: each card shall present a load to the socket no larger than 50 pF 10 at a DC current of 700 μA low state and 150 μA high state, including pull-resistor. The socket shall be able to drive at least the following load 10 while meeting all AC timing requirements: (the number of sockets wired in parallel) multiplied by (50 pF with DC current 700 μA low state and 150 μA high state per socket).
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Ultra DMA Electrical Requirements Host and Card signal capacitance limits for Ultra DMA operation The host interface signal capacitance at the host connector shall be a maximum of 25 pF for each signal as measured at 1 MHz. The card interface signal capacitance at the card connector shall be a maximum of 20 pF for each signal as measured at 1 MHz.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Table: Ultra DMA Termination with Pull-up or Pull down Example Printed Circuit Board (PCB) Trace Requirements for Ultra DMA On any PCB for a host or device supporting Ultra DMA: The longest D[15:00] trace shall be no more than 0.5" longer than either STROBE trace as measured from the IC pin to the connector. The shortest D[15:00] trace shall be no more than 0.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Attribute Memory Read Timing Specification Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Configuration Register (Attribute Memory) Write Timing Specification Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Common Memory Read Timing Specification Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Common Memory Write Timing Specification Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd I/O Input (Read) Timing Specification Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd I/O Output (Write) Timing Specification Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd True IDE PIO Mode Read/Write Timing Specification Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd True IDE Ultra DMA Mode Read/Write Timing Specification Table: Ultra DMA Data Burst Timing Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Notes: 1) All timing measurement switching points (low to high and high to low) shall be taken at 1.5 V. 2) All signal transitions for a timing parameter shall be measured at the connector specified in the measurement location column. For example, in the case of tRFS, both STROBE and –DMARDY transitions are measured at the sender connector.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Notes: 1) The parameters tUI, tMLI : (Ultra DMA Data-In Burst Device Termination Timing and Ultra DMA Data-In Burst Host Termination Timing), and tLI indicate sender-to-recipient or recipient-to-sender interlocks, i.e., one agent (either sender or recipient) is waiting for the other agent to respond with a signal before proceeding. tUI is an unlimited interlock that has no maximum time value.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Note: 1) The sender shall be tested while driving an 18 inch long, 80 conductor cable with PVC insulation material. The signal under test shall be cut at a test point so that it has not trace, cable or recipient loading after the test point. All other signals should remain connected through to the recipient.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Card Configuration The CompactFlash Storage Cards and CF+ Cards are identified by appropriate information in the Card Information Structure (CIS). The following configuration registers are used to coordinate the I/O spaces and the Interrupt level of cards that are located in the system.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Table: CF+ Card Register and Memory Space Decoding Table: CF+ Card Configuration Registers Decoding Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Attribute Memory Function Attribute memory is a space where CompactFlash Storage Card and CF+ Card identification and configuration information are stored, and is limited to 8 bit wide accesses only at even addresses. The card configuration registers are also located here. For CompactFlash Storage Cards, the base address of the ard configuration registers is 200h.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Configuration Option Register (Base + 00h in Attribute Memory) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Card Configuration and Status Register (Base + 02h in Attribute Memory) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Pin Replacement Register (Base + 04h in Attribute Memory) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Socket and Copy Register (Base + 06h in Attribute Memory) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd I/O Transfer Function The I/O transfer to or from the CompactFlash Storage or CF+ Card can be either 8 or 16 bits. When a 16 bit accessible port is addressed, the signal -IOIS16 is asserted by the CompactFlash Storage or CF+ Card. Otherwise, the -IOIS16 signal is de-asserted.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Common Memory Transfer Function The Common Memory transfer to or from the CompactFlash Storage or CF+ Card can be either 8 or 16 bits. Table: Common Memory Function Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd True IDE Mode I/O Transfer Function The CompactFlash Storage Card and CF+ Card can be configured in a True IDE Mode of operation. The CompactFlash Storage Card is configured in this mode only when the -OE input signal is grounded by the host during the power off to power on cycle. Optionally, CompactFlash Storage Cards and CF+ Cards may support the following optional detection methods: 1.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Metaformat Overview The goal of the Metaformat is to describe the requirements and capabilities of the CompactFlash Storage Card and CF+ Card as thoroughly as possible. This includes describing the power requirements, IO requirements, memory requirements, manufacturer information and details about the services provided.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd CF-ATA Drive Register Set Definition and Protocol The CompactFlash Storage Card can be configured as a high performance I/O device through: a) The standard PC-AT disk I/O address spaces 1F0h-1F7h, 3F6h-3F7h (primary) or 170h- 177h, 376h-377h (secondary) with IRQ 14 (or other available IRQ). b) Any system decoded 16 byte I/O block using any available IRQ. c) Memory space.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd I/O Primary and Secondary Address Configurations Table: Primary and Secondary I/O Decoding Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Contiguous I/O Mapped Addressing When the system decodes a contiguous block of I/O registers to select the CompactFlash Storage Card, the registers are accessed in the block of I/O space decoded by the system as follows: Table: Contiguous I/O Decoding Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Memory Mapped Addressing When the CompactFlash Storage Card registers are accessed via memory references, the registers appear in the common memory space window: 0-2K bytes as follows: True IDE Mode Addressing When the CompactFlash Storage Card or CF+ Card is configured in the True IDE Mode, the I/O decoding is as follows: Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd CF-ATA Registers The following section describes the hardware registers used by the host software to issue commands to the CompactFlash device. These registers are often collectively referred to as the “task file.” Data Register (Address - 1F0h[170h];Offset 0,8,9) The Data Register is a 16 bit register, and it is used to transfer data blocks between the CompactFlash Storage Card data buffer and the Host.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Feature Register (Address - 1F1h[171h]; Offset 1, 0Dh Write Only) This register provides information regarding features of the CompactFlash Storage Card that the host can utilize. This register is also accessed in PC Card modes on data bits D15-D8 during a write operation to Offset 0 with -CE2 low and -CE1 high.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Bit 3 (HS3): when operating in the Cylinder, Head, Sector mode, this is bit 3 of the head number. It is Bit 27 in the Logical Block Address mode. Bit 2 (HS2): when operating in the Cylinder, Head, Sector mode, this is bit 2 of the head number. It is Bit 26 in the Logical Block Address mode. Bit 1 (HS1): when operating in the Cylinder, Head, Sector mode, this is bit 1 of the head number.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Device Control Register (Address - 3F6h[376h]; Offset Eh) This register is used to control the CompactFlash Storage Card interrupt request and to issue an ATA soft reset to the card. This register can be written even if the device is BUSY. The bits are defined as follows: Bit 7: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Card (Drive) Address Register (Address 3F7h[377h]; Offset Fh) This register is provided for compatibility with the AT disk drive interface. It is recommended that this register not be mapped into the host’s I/O space because of potential conflicts on Bit 7. Bit 7: this bit is unknown.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd CF-ATA Command Set CF-ATA Command Set summarizes the CF-ATA command set with the paragraphs that follow describing the individual commands and the task file for each. Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Definitions: FR = Features Register SC = Sector Count RegisterS SN = Sector Number Register CY = Cylinder Registers DH = Card/Drive/Head Register LBA = Logical Block Address Mode Supported (see command descriptions for use). Y - The register contains a valid parameter for this command.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Execute Drive Diagnostic - 90h When the diagnostic command is issued in a PCMCIA configuration mode, this command runs only on the CompactFlash Storage Card that is addressed by the Drive/Head register. This is because PCMCIA card interface does not allows for direct inter-drive communication (such as the ATA PDIAG and DASP signals).
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Flush Cache – E7h This command causes the card to complete writing data from its cache. The card returns status with RDY=1 and DSC=1 after the data in the write cache buffer is written to the media. If the Compact Flash Storage Card does not support the Flush Cache command, the Compact Flash Storage Card shall return command aborted.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Identify Device – Ech The Identify Device command enables the host to receive parameter information from the CompactFlash Storage Card. This command has the same protocol as the Read Sector(s) command. The parameter words in the buffer have the arrangement and meanings defined in Table as below. All reserved bits or words are zero. Hosts should not depend on Obsolete words in Identify Device containing 0.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Word 0: General Configuration This field indicates the general characteristics of the device. When Word 0 of the Identify drive information is 848Ah then the device is a CompactFlash Storage Card and complies with the CFA specification and CFA command set. It is recommended that PCMCIA modes of operation report only the 848Ah value as they are always intended as removable devices.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Word 1: Default Number of Cylinders This field contains the number of translated cylinders in the default translation mode. This value will be the same as the number of cylinders. Word 3: Default Number of Heads This field contains the number of translated heads in the default translation mode.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Translation Parameters Valid Bit 0 shall be set to 1 indicating that words 54 to 58 are valid and reflect the current number of cylinders, heads and sectors. If bit 1 of word 53 is set to 1, the values in words 64 through 70 are valid. If this bit is cleared to 0, the values reported in words 64-70 are not valid.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Of these bits, bits 7 through 2 are reserved. Bit 0, if set to one, indicates that the CompactFlash Storage Card supports PIO mode 3. Bit 1, if set to one, indicates that the CompactFlash StorageCard supports PIO mode 4. Support for PIO modes 5 and above are specific to CompactFlash are reported in word 163.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Bit 0 of word 82 shall be set to zero; the SMART feature set is not supported. If bit 1 of word 82 is set to one, the Security Mode feature set is supported. Bit 2 of word 82 shall be set to zero; the Removable Media feature set is not supported. Bit 3 of word 82 shall be set to one; the Power Management feature set is supported. Bit 4 of word 82 shall be set to zero; the Packet Command feature set is not supported.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd command. Bit 14 of word 85 shall be set to one; the CompactFlash Storage Card supports the NOP command. Bit 15 of word 85 is obsolete. Bit 0 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Download Microcode command. Bit 1 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Read DMA Queued and Write DMA Queued commands.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Word 91: Advanced power management level value Bits 7-0 of word 91 contain the current Advanced Power Management level setting. Word 128: Security Status Bit 8: Security Level If set to 1, indicates that security mode is enabled and the security level is maximum. If set to 0 and security mode is enabled, indicates that the security level is high.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Word 63: Multiword DMA transfer and 6.2.1.6.19: Word 64: Advanced PIO transfer modes supported. Bits 2-0: Advanced True IDE PIO Mode Support Indicates the maximum True IDE PIO mode supported by the card. Bits 5-3: Advanced True IDE Multiword DMA Mode Support Indicates the maximum True IDE Multiword DMA mode supported by the card.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Word 164: CF Advanced PCMCIA I/O and Memory Timing Modes Capabilities and Settings This word describes the capabilities and current settings for CFA defined advanced timing modes using the Memory and PCMCIA I/O interface. Notice! The use of PCMCIA I/O or Memory modes that are 100ns or faster impose significant restrictions on the implementation of the host: Additional Requirements for CF Advanced Timing Modes.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Idle Immediate - 95h or E1h This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. Initialize Drive Parameters - 91h This command enables the host to set the number of sectors per track and the number of heads per cylinder. Only the Sector Count and the Card/Drive/Head registers are used by this command.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Read Buffer - E4h The Read Buffer command enables the host to read the current contents of the CompactFlash Storage Card’s sector buffer. This command has the same protocol as the Read Sector(s) command. Read DMA – C8h Read Long Sector - 22h or 23h Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Read Multiple - C4h Read Sector(s) - 20h or 21h Read Verify Sector(s) - 40h or 41h Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Recalibrate - 1Xh Request Sense - 03h The extended error code is returned to the host in the Error Register. Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Seek - 7Xh Set Features – EFh Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Feature Supported Features 01h and 81h are used to enable and clear 8 bit data transfer modes in True IDE Mode. If the 01h feature command is issued all data transfers shall occur on the low order D[7:0] data bus and the -IOIS16 signal shall not be asserted for data register accesses. The host shall not enable this feature for DMA transfers.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Set Multiple Mode - C6h Set Sleep Mode- 99h or E6h Standby - 96h or E2h Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Standby Immediate - 94h or E0h Translate Sector - 87h Translate Sector Information Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Wear Level - F5h Write Buffer - E8h Write DMA – CAh Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Write Long Sector - 32h or 33h Write Multiple Command - C5h Write Multiple without Erase – CDh Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Write Sector(s) - 30h or 31h Write Sector(s) without Erase - 38h Write Verify - 3Ch Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Error Posting Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Error and Status Register summarizes the valid status and error value for all the CF-ATA Command set. Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd CompactFlash Adapters CompactFlash and CF+ Type I products can be used with a PCMCIA Type I passive adapters. This adapter converts the Type I CompactFlash Storage Card or CF+ Card into a Type II PCMCIA PC card. Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd C.H.S. Table This table show default number of cylinders, heads and sectors for the various models. Transcend Information Inc.
TTrraannsscceenndd IInndduussttrriiaall (( 112288M MB B ~~ 88G GB B )) C CFF C Caarrdd Above technical information is based on industry standard data and tested to be reliable. However, Transcend makes no warranty, either expressed or implied, as to its accuracy and assumes no liability in connection with the use of this product. Transcend reserves the right to make changes in specifications at any time without prior notice. Transcend Information Inc.