SATA III 2242 M.2 SSD MTS400I Datasheet Products Product Description TS512GMTS400I M.2 2242 SSD, SATA3 B+M Key, MLC, Wide Temp TS256GMTS400I TS128GMTS400I Datasheet version TS64GMTS400I 1.1 TS32GMTS400I TS16GMTS400I No.70, Xingzhong Rd., Neihu Dist.,Taipei City 114, Taiwan, R.O.C. Tel:+886-2-2792-8000 Fax:+886-2-2792-1614 www.transcend-info.com Copyright© Transcend Information, Inc. All Rights Reserved.
Revision History Revision No. History Released Date Editor by 1.0 First version (WD 15nm) 2019/12/31 TSD 1.1 Vibration Format Updated Add 2.6 Recommended Measurement Point Revise 5.2.5 PS(Power shield) description Remove 5.2.
Transcend MTS400I Features Part Name Capacity TS512GMTS400I 512GB TS256GMTS400I 256GB TS128GMTS400I 128GB TS64GMTS400I 64GB TS32GMTS400I 32GB TS16GMTS400I 16GB FEATURES SATA 6Gbps 2D MLC NAND Flash Wide-temperature operation M.
Table of Content 1 Introduction…………………………………………………………………….……………………………………………..5 1.1 General Feature Information……………………………………………………………….……………….5 1.2 Product List………………………………………….………………………………………………..……………5 1.3 Ordering Information…………………………….……..…………………………………………….………6 2 Product Specifications……………………………………………………..………………………………………….. 7 2.1 Interface and Compliance………………...…………………………………………………….…….……7 2.2 Drive Capacity………………………………….………………………………………………………….…..…7 2.3 System Performance………………………….
1. Introduction 1.1 General Feature Information Hardware Feature - SATA 6Gbps - Transcend Controller TS6500 - 2D MLC NAND Flash - Temperature operation from -40°C to 85°C - M.2 SATA 2242 B+M Key - Embedded DDR3 DRAM cache - Power shield function - AES-256 function (Optional) Firmware Feature - Global wear-leveling function - Enhance Bad block management function - BCH ECC(Error Correction Code) function - TRIM Command function - Advanced Garbage Collection function - StaticDataRefresh function - S.M.A.R.T.
1.3 Ordering Information TSXXXGMTS400I 1 2 3 4 1 – Transcend 2 – SSD Density 3 – G: Gigabyte; T: Terabyte 4 – M.
2. Product Specifications 2.1 Interface and Compliance - SATA3, compatible to SATA2 and SATA1 Compatible with ATA/ATAPI-7 Standard Native Command Queuing(NCQ) Command Set RoHS Compliance CE, FCC and BSMI Compliance 2.2 Drive Capacity [Table 1] User Capacity and Addressable Sectors User-Addressable Sectors 16GB 32GB 64GB 128GB 31,277,232 62,533,296 125,045,424 250,069,680 Byte per Sector 512 Byte User-Addressable Sectors 256GB 512GB 500,118,192 1,000,215,216 512 Byte Byte per Sector 2.
4K file size and queue depth of 32, unit IOPs 2) The recorded performance is obtained while the SSD is not operated as an OS disk Physical Specification. 2.4 Supply Voltage [Table 4] Supply Voltage Item Requirements 3.3V±5% Allowable voltage Allowable noise / ripple 100 mV p-p or less 2.5 System Power Consumption [Table 5] Power Consumption Read / Write 16GB 32GB 64GB 128GB 256GB 512GB 0.62W 0.78W 1.06W 1.52W 1.52W 2.48W Active Read (Max.)1) 0.61W 0.73W 0.73W 0.76W 0.96W 1.
Recommended Measurement Point Recommended temperature measurement point is in the center of the connector inserted by the device. Sufficient airflow is recommended for proper operation on heavier workloads within the device operating temperature. 2.7 System Reliability [Table 7] Telcordia SR332 issue 4 MTBF Specifications Parameter 16GB 32GB 64GB MTBF 128GB 256GB 512GB 256GB 512GB 2,500,000 hours Note: 1) The calculation is based on 25°C.
[Table 10] Drive Write Per Day (DWPD) Specifications Parameter 16GB 32GB 64GB DWPD1) 128GB 256GB 512GB 2 (3 Years) Note: 1) DWPD is based on [Table 11] value and Warranty year to calculate. [Table 11] Data Retention Specifications Parameter 16GB 32GB 64GB Data Retention 128GB 256GB 512GB 1 year Note: 1) Data retention was measured by assuming that SSD reaches the maximum rated endurance at 30°C in power-off state.
3. Mechanical Specification The figure below illustrates the Transcend M.2 Type 2242-D2-B-M Solid State Drive. [Table 15] Physical Dimensions and Weight Model Height (mm) Width (mm) Length (mm) Weight (gram) 16GB/32GB/64GB/128GB/ 256GB/512GB Max 3.58 22.00±0.15 42.00±0.
4. Pin Assignment 4.1 Pin Assignments [Table 16] Pin Assignments Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name 01 CONFIG_31) 02 3.3V 39 GND 40 NC 03 GND 04 3.
5. Block Diagram and Function Explanations 5.1 Block Diagram 5.2 Function Explanations 5.2.1 Global Wear Leveling Function Global wear leveling ensures that every block has an even erase count. This helps to extend the life expectancy of an SSD. There are three main processes in global wear leveling: (1) Record the block erase count and save this in the wear-leveling table. (2) Find the static-block and save this in the wear-leveling pointer.
5.2.4 StaticDataRefresh Technology Normally, ECC engine corrections are taken place without affecting the host normal operations. As time passes by, the number of error bits accumulated in the read transaction exceeds the correcting capability of the ECC engine, resulting in corrupted data being sent to the host.
5.2.8 TCG-Opal Function(Optional) Opal is a comprehensive set of guidelines. The target audience includes manufacturers of storage devices, software vendors, system integrators, and academia. These specifications cover the manufacture of storage devices, system setup, management, and use; they allow for password protection and hierarchical storage management, while preventing data from being stolen or tampered with.
6. Technology Term Explanations 6.1 TBW Terabytes Written (TBW) directly measures how much you can write cumulatively into the drive over its lifetime. Essentially, it just includes the multiplication we did above in the measurement itself. For example, if your drive is rated for 365 TBW, that means you can write 365 TB into it before you may need to replace it. If its warranty period is 5 years, that works out to 365 TB ÷ (5 years × 365 days/year) = 200 GB of writes per day.
7. Installation Requirements 7.1 Card Insertion Angles insertion is allowable and preferred; intent is to minimize the insertion/extraction force. Minimum of angle of insertion is 5° Minimum two step insertion is desirable; intent is to minimize the insertion/extraction force.
8. Command Descriptions 8.1 Support ATA Commands This table and the following paragraphs summarize the ATA command set.
SMART Enable/Disable Autosave B0h Non-data SMART Enable Operations B0h Non-data SMART Execute Off-Line Immediate B0h Non-data SMART Read LOG B0h PIO data-In SMART Read Data B0h PIO data-In SMART Read THRESHOLD B0h PIO data-In SMART Return Status B0h Non-data SMART SAVE ATTRIBUTE VALUES B0h Non-data SMART WRITE LOG B0h PIO data-out Read Native Max Address F8h Non-data Set Max Address F9h Non-data Set Max Set Password F9h PIO data-out Set Max Lock F9h Non-data Set Max Fr
8.
8.3 SMART Attributes The following table shows the vendor specific data in byte 2 to 361 of 512-byte SMART data.
9. Contact Information TAIWAN JAPAN No.70, XingZhong Rd., NeiHu Dist., Taipei, Taiwan, R.O.C TEL +886-2-2792-8000 Fax +886-2-2793-2222 E-mail: sales-tw@transcend-info.com E-mail: sales-jp@transcend-info.com Shanghai GERMANY E-mail: sales-cn@transcendchina.com TEL: +86-21-6161-9388 E-mail: sales-de@transcend-info.com TEL: +49-40-538-907-0 Beijing NETHERLANDS E-mail: sales-cn@transcendchina.com E-mail: sales-nl@transcend-info.
