User's Manual

ManualsBrandsTransCore ManualsElectronicsLOW POWER TRANSMITTER (2400-2483.5 MHz)

ROVR SIDEKICK Installation and Operation v1.0 | Document Number 412158 Page 1 of 6

ROVR SIDEKICK

™

Installation and Operation

This document describes how to correctly install a

ROVR SIDEKICK™

device. The

ROVR

SIDEKICK

used with the

ROVR™

vehicle tracking unit for convenience in viewing toll rates

and paying for HOT lane use.

These instructions cover what you need to know to get your ROVR Sidekick up and running:

• Battery Installation

• Sidekick Unit Installation

• Operation

Battery Installation

The Sidekick requires 2 AAA batteries for

operation. Non-rechargeable lithium batteries

are recommended for maximum life. Some

high capacity alkaline batteries will also be

sufficient but have shorter lifetimes.

The Sidekick has a battery compartment.

Batteries are inserted in-line to the

compartment through a small door on the

side of the unit.

Open the door by removing the attached

thumbscrew.

Insert both batteries negative (-) terminal first.

The top of the batteries will protrude from

the opening.

Thumbscrew

Door (removed)

Battery

compartment

Summary of content (6 pages)

PAGE 1
ROVR SIDEKICK™ Installation and Operation This document describes how to correctly install a ROVR SIDEKICK™ device. The ROVR SIDEKICK is used with the ROVR™ vehicle tracking unit for convenience in viewing toll rates and paying for HOT lane use. These instructions cover what you need to know to get your ROVR Sidekick up and running: • Battery Installation • Sidekick Unit Installation • Operation Battery Installation 1 The Sidekick requires 2 AAA batteries for operation.
PAGE 2
3 Manipulate the battery tab opposite the thumbscrew into the opening and screw the door back in. This requires a small amount of force to overcome the internal battery spring. Thumbscrew Battery tab 4 When the door is fully in place, the display should light with a message that reads ROVR SIDEKICK, along with a version number. ROVR SIDEKICK Installation and Operation v1.0 | Document Number 412158 ROVR SIDEKICK VERSION X.
PAGE 3
Sidekick Unit Installation Your ROVR Sidekick kit includes the necessary parts to attach the unit to: • the vehicle visor with a clip, or to • the windshield with either double-sided adhesive or suction cups. Visor Mount Clip Windshield Mount Adhesive Suction Cups ROVR SIDEKICK Installation and Operation v1.
PAGE 4
Operation The ROVR Sidekick has two “rocker” switches, one on each side, that allow you to power the unit on and off, select the number of occupants in your vehicle, and choose to use a HOT lane payment. Each switch has 3 positions: Up, Center, and Down. When you press the switch, it rocks to the position you choose and then returns to center. A display on the ROVR Sidekick shows messages.
PAGE 5
Use the HOT Lane 1 Make sure you have selected the correct number of occupants. 2 PEOPLE 2 Enter Pre-Toll Geo-zone. Choose DISPLAY TOLL (Center) –or- press PWR/DISPLAY (Down). The ROVR Sidekick shows the toll amount. Continue current route towards the HOT Lane. HOT LANE AHEAD TOLL $2.34 3 Press PAY TOLL (Up). The ROVR Sidekick confirms your choice. 4 Enter Toll area. You are charged according to your occupancy setting: ALLOW CHARGES 2 PEOPLE HOT LANE ENTRY PAID $2.
PAGE 6
Turn Off the ROVR Sidekick Press and hold PWR/DISPLAY for 2.5 seconds. This message flashes before the ROVR Sidekick powers off: TURNING OFF Regulatory and Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, and Industry Canada license-exempt RSS standard(s).