Instruction Manual

ManualsBrandsTRANSGO ManualsVB sTRANSGO RE4FO4 VB's

Sentra 2000-05

Infinity G20 2000-02

RE4FO Identify 4 May 2011

Case O-ring

Yellow

Plastic

RE4FO3 A models: The internal solenoid wires

extend outside of the case as shown below.

Use SK® RE4FO3A

For Hot Rods Only:

Use RE4FO3A HD-2 Reprogramming Kit®

Case O-ring

RE4FO3 B models: The internal solenoid wiring

harness DOES NOT extend outside of the case!

Use SK® RE4FO3B

For Hot Rods Only:

Use RE4FO3B HD-2 Reprogramming Kit®

Black

Plastic

This part of harness extends outside of case!

Over

A Bodies

Have 2 holes in

circled area.

B Bodies

Have 1 hole in

circled area.

No hole in casting

Sentra 1993-99

200SX 1995- 98

Infinity G20 1994-99

For RE4FO4 (Large Case) VB’s See other side.

HOLD IT! Identify the valve body first!

No hole in casting

This VB has a

PWM Lock-up

system.

This VB has a

on-off Lock-up

system.

RE4FO3 Pan

Gasket

Summary of content (12 pages)

PAGE 1
HOLD IT! Identify the valve body first! For RE4FO4 (Large Case) VB’s See other side. RE4FO3 A models: The internal solenoid wires RE4FO3 B models: The internal solenoid wiring harness DOES NOT extend outside of the case! Use SK® RE4FO3B For Hot Rods Only: Use RE4FO3B HD-2 Reprogramming Kit® Black Plastic extend outside of the case as shown below.
PAGE 2
HOLD IT! Identify the valve body first! For RE4FO3 (Small Case) VB’s See other side. RE4FO4 A&V models: The internal solenoid RE4FO4 B models: The internal solenoid wiring harness DOES NOT extend outside of the case! Use SK® RE4FO4B For Hot Rods Only: Use RE4FO4B HD-2 Reprogramming Kit® Black Plastic wires extend outside of the case as shown below.
PAGE 3
RE4F03A Shift Kit ® Front Drive Nissan--Without TV Cable Sentra GXE 93-99 200SX 95-98 G20 Infinity 94-99 You never felt a Nissan shift this good, Hot or COLD. This Kit is about: Rough 2nd cold. No 3rd after a 3-2 or 4-2 kickdown. Direct clutch (3rd) inner seal leaks, wears or opens up, etc. Corrects Hard and Soft 1-2. Long 2 -3 at heavy throttle. Firmer 4th and lockup. Flat Bent Pry Eyelet Pry End plug Step 1. Remove Retainers. With sand paper smooth the small burr where the retainer was against bore.
PAGE 4
Upper Valve Body You’ll love the 1- 2 shift. Short--Smooth- -No bangs Checkballs: Five Steel .214 to .218 Don’t use plastic balls. Use some Vaseline to keep the checkballs in place NOT grease. Hello Mechanic: Install accumulator valve first. Then install the flat washer on the stem of accum valve, then the remaining parts as shown. Step 1. Remove the accum valve. Chamfer partition as shown at bottom of page. Clean the bore. Reinstall valve. Install the WHITE spring, end plug and retainer. Step 2.
PAGE 5
Upper Valve Body Upper Separator Plate Enlarge this hole with .110 drill. Enlarge with .086 drill. .046 .086 .
PAGE 6
Checkballs: Channel Casting Six steel .214 to .218 Don’t use plastic balls. Use some Vaseline to keep the checkballs in place NOT grease.
PAGE 7
Main Separator Plate Enlarge holes with .110 drill. Enlarge hole with .046 drill. Enlarge hole with .086 drill.
PAGE 8
Main Valve Body 4. Install Springs & Gold Steel Balls furnished. 3. Enlarge the limit drain Gold Steel balls .265 diam holes with a 1/4” drill. ORANGE 2. Install Green pressure regulator spring furnished. GREEN Dummy valve Retainers SK RE4FO3A 4 May 2011 Retainers LISTEN UP: Install the retainers in correct locations in VB. Page 6 ORANGE End plug 1. Install ORANGE spring.
PAGE 9
You must be able to wiggle band back and forth at least 1/16” . 2nd piston 4th piston Check Band Adjustment: Install 2nd piston with new cushion seat and spring. If band will wiggle on drum 1/16” by hand, you can skip the band adjustment shown below. Remove and discard original hard washer. Cushion seat ORANGE RED 1. Do step 2 if trans is out of vehicle. Poor design 3-4 clutch inner piston seal causes trans to lose 3rd & 4th. Usually worse when hot or after Kickdown. Reuse 2.
PAGE 10
VB to Case Bolts “A” “B” “C” A Six bolts 1.455” Five bolts 1.725” Two bolts 1.885” B C Tighten VB bolts to 95 IN. LB. Pan bolts to 65-80 IN. LB. Drain plug to 25 FT. LB.
PAGE 11
Four solenoid bolts .680” 2.765” Valve Body Bolts 1.730” 3.230” starter bolt 1.730” 13 bolts necessary to remove VB from the case. Tighten VB bolts to 95 IN. LB. Tighten hold down bolts and plates to 70-80 IN. LB. 2.455” bolt under filter .680” 2.765” 1.730” .680” 2.455” bolt under filter 2.765” 2.765” 1.462” cover bolt 2.765” 1.730” 2.765” 1.730” SK RE4FO3A 4 May 2011 1.730” Page 9 1.462” cover bolt 2.765” 2.455” 3.
PAGE 12
Bolts shown in actual size. Starter bolt 3.230” Two 2.765” Eleven 2.455” Three 1.730” Six .870” One .680” Six Cover .870” Cover Starter bolt Page 10 SK RE4FO3A 4 May 2011 1.462” Hold down plates and bolts.