SISTF1010-150-LR(T) 10/100Base-TX Industrial Unmanaged Switch Installation Manual Rev.
Transition Networks Table of Contents Trademark, copyright, and product classification information ......................................................................... iii Trademark.................................................................................................................................................. iii Copyright restrictions ................................................................................................................................. iii FCC warning .....
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Section IV:...............................................................................................................................................................20 Cable Specifications................................................................................................................................................20 Introduction .........................................................................................
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Trademark, copyright, and product classification information Trademark All trademarks and registered trademarks are the property of their respective owners. Copyright restrictions © 2007 Transition Networks: All rights reserved. No part of this work may be reproduced or used in any form or by any means—graphic, electronic, or mechanical—without written permission from Transition Networks. Printed in the U.S.A.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch About this product and manual Industrial Switch The SISTF1010-150-LR(T) Industrial Unmanaged Switch provides five 10/100Base-TX (RJ45) copper connections. These switches are hardened devices designed to reliably operate in harsh environments such as those found on factory floors, outdoor enclosures or other hazardous environments.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Cautions and warnings Cautions and warnings Make sure that you read and understand all content identified by these two symbols: Cautions and warnings appear here and throughout this manual where appropriate. Failure to read and understand the information identified by the “caution” and “warning” symbols could result in poor equipment performance, damage to equipment, or injury to persons.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Cautions and warnings, continued Warnings Warnings indicate the possibility of injury to persons. WARNING Be sure to disconnect power before installing and wiring the Industrial Switch. Failure to observe this warning could result in an electrical shock. WARNING Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
Section I SISTF1010-150 Industrial Unmanaged Switch In this section These are the topics: Topic General description SISTF1010-150 Industrial Unmanaged Switch model numbers Package Contents Physical Description See Page 2 3 4 5
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch General description Overview The SISTF1010-150 Industrial Unmanaged Switch can help aggregate and transport data from copper-based industrial networking and communication devices.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks SISTF1010-150 Industrial Unmanaged Switch part numbers Standard models The part numbers shown in Tables 1 and 2 perform as described in this manual.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Package contents Package contents Quantity 1 1 1 6 1 1 Description 10/100BaseTX Industrial Unmanaged Switch DIN-Rail mounting bracket (installed) One wall mount plate Screws (for attaching wall-mount bracket) Installation manual CD Barrel connector interface cable - For external AC/DC power supply (sold separately) Compare the package contents of your industrial Switch with the standard checklist above.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Physical description Physical dimensions Width: 2.1” [54mm] Height: 5.3” [135mm] Depth: 4.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Physical description, continued Bottom panel The bottom view of the Industrial Switch is shown in Figure 2 with corresponding descriptions listed below: Grounding Screw 6-position terminal block Primary power input terminals (2) Secondary power input terminals (2) Figure 2: SISTF1010-150-LR(T) Industrial Switch (Bottom View) Back panel The back view of the Industrial Switch is shown in Figure 3 with corresponding descriptions liste
Section II Installation In this section These are the topics: Topic DIN rail mounting Wall mounting Grounding the Industrial Switch Connecting power to the Industrial Switch Connecting copper cable Light Emitting Diodes (LEDs) See Page 8 10 11 12 16 17
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch DIN rail mounting DIN rail clip The Industrial Switch includes an aluminum DIN Rail Clip attached to the rear panel. Verify the clip is attached and oriented as pictured in Figure 4 below.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks DIN rail mounting, continued DIN rail mounting To mount the Industrial Switch to the DIN rail, see Figure 5 and do the following: Step Action 1. Align and then position DIN-Rail-clip spring to the top of the DIN rail as shown in Figure 5, step (a). 2. Press DOWN on the Industrial Switch and then IN to snap it into place on the DIN Rail. See Figure 5, step (b).
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Wall mounting Wall mount bracket The Industrial Switch includes a wall mount bracket and screws in the contents of the shipping package. The wall mount bracket can be attached to the rear panel of the Industrial Switch to enable mounting to a vertical surface such as the wall of an enclosure. Locate the bracket (1) and screws (6) and follow the steps below to install the bracket on the Industrial Switch.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Grounding the Industrial Switch CAUTION Be sure to disconnect the Industrial Switch from the DC power source before installing and wiring the device. Wiring considerations The following wiring considerations are recommended: • Signal lines must not be directly connector to outdoor wiring. • Use separate paths or conduits to route wiring for power and device data cables.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Connecting power to the Industrial Switch Redundant power inputs The Industrial Switch has dual (redundant) power inputs capable of auto-sensing the input voltage, while providing over current protection and reverse polarity protection. The dual power inputs can be connected simultaneously to live DC power sources. See Figure 8.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Connecting power to the Industrial Switch, continued Note: Terminal-block wiring The terminal block can accept 12 – 24 AWG wire for power and alarm relay inputs. To wire the 6-position terminal block for redundant power, do the following: Note: Step 1. 2. 3. 4. 5. The 6-position terminal-block plug is constructed (keyed) to mate with the Industrial Switch terminal block.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Connecting power to the Industrial Switch, continued Terminal-block wiring (continued) Step 6. Action Insert the terminal block plug into the Industrial Switch’s terminal block, as shown in Figure 10. Figure 10: Wired Terminal Block Plug Inserted Into Industrial Switch 7. 8. 14 Make sure that the DC power source is stable and clean.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Connecting power to the Industrial Switch, continued Barrel connector interface cable A barrel connector interface cable is included with the Industrial Switch and can be used to convert the barrel connector output of an external AC/DC power supply over to a wire interface that can then be inserted into the terminal block following the instructions and figure 9, both located on page 13 of this manual.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Connecting copper cables Copper cable installation To connect the copper cable to the Industrial Switch and other equipment, do the following: Step 1. 2. 3. 4. Action Locate or build 10Base-T or 100Base-TX copper cables with male, RJ-45 connectors installed at both ends. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the Industrial Switch. See Figure 12 below.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Light Emitting Diodes (LEDs) LEDs The Industrial Switch has LED indicators located on its front panel. The LEDs present at-aglance network status, and provide real-time connectivity information. Figure 14 shows the LEDs and a chart that explains the function of each.
Section III: Advanced Features Introduction This section provides an explanation of the advanced features on the Industrial Switch.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Advanced Features AutoCross TM TM AutoCross automatically detects and configures the twisted pair port on the converter to the correct MDI or MDI-X configuration allowing either straight-through (MDI) or crossover (MDI-X) cables to be used – see figure 15. No user intervention is required.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Section IV: Cable Specifications Introduction This section provides copper cable specifications.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Copper (RJ-45) cable specifications Copper cabling Shielded twisted-pair (STP) or unshielded twisted-pair (UTP) cabling may be used and can be configured as either Straight-through or crossover – see figure 16.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Section V: Troubleshooting Introduction This section provides basic troubleshooting information for the Industrial Switch via a problem and corrective action table. The problems are stated in the problem column and the action(s) to take for the problem is stated in the corrective action column.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Troubleshooting problem and corrective action table Problem Industrial Switch does not power up No link or activity on the UTP port Potential Cause • Is the wired terminal-block plug fully inserted into the Industrial Switch? Potential Solution • Wire and insert the terminal-block plug into the Industrial Switch’s terminal block – See pages 12-16 • Is the power LED lit? • Check that DC power is at the recommended levels.
Section VI: Contact Us, Warranty, & Compliance Information Introduction This section explains how to contact Transition Networks via Phone, fax, email, and direct mail.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Contact us Technical support Technical Support is available 24 hours a day. United States: 1-800-260-1312 International: 00-1-952-941-7600 Live Web chat Chat live via the Web with a Transition Networks Technical Support Specialist. Log onto www.transition.com and click the Transition Now link. Web-based training Transition Networks provides 8-10 seminars per month via live web-based training. Log onto www.transition.
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Warranty Limited lifetime warranty Effective for products shipped May 1, 1999 and after, every Transition Networks’ labeled product will be free from defects in material and workmanship for its lifetime. This warranty covers the original user only and is not transferable.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks Warranty, continued Customer pays non-compliant return costs The customer must pay the non-compliant product(s) return transportation cost to Transition Networks for evaluation of said product(s) for repair or replacement. Transition Networks will pay for shipping the repaired or replaced in-warranty product(s) back to the customer (any and all customs charges, tariffs, or/and taxes are the customer’s responsibility).
Transition Networks SISTF1010-150-LR(T) Industrial Unmanaged Switch Compliance information Compliances CISPR22/EN5022 Class A + EN55024; EN60950 Class A; FCC Class A; CE Mark UL Listed; C-UL Listed The following part numbers are UL Listed: SISTF1010-150-LR, SISTF1010-150-LRT. (Canada) FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules.
SISTF1010-150-LR(T) Industrial Unmanaged Switch European Regulations, (continued) Transition Networks In accordance with European Union Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003, Transition Networks will accept post usage returns of this product for proper disposal. The contact information for this activity can be found in the ‘Contact Us’ portion of this document. CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK.
Appendix A: Technical Specifications SISTF1010-150-LR(T) specifications, notices, and warnings Parameter Standards Regulatory Compliance for Emissions Safety Compliance EMI Compliance Environmental Compliance Ports Max Distance Max Data Rate Signals MAC Addresses Memory Buffer Transfer Rate Packet Throughput Backplane Power Consumption Ingress Protection MTBF Input Power Dimensions Weight Shipping weight Standard Operating Temperature Description TM TM TM IEEE 802.3 , 802.3u , 802.
SISTF1010-150-LR(T) Industrial Unmanaged Switch Transition Networks SISTF1010-150-LR(T) specifications, notices, and warnings, continued Notices • The information in this user’s guide is subject to change. For the most up-to-date information on the SISTF1010-150-LR(T) Industrial Unmanaged Switch, please refer to the user’s guide on-line at: www.transition.com. • Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable at the date of manufacture.